• Warranty • Assembly • Parts TOOLS REQUIRED FOR ASSEMBLY - Adjustable Wrench - Pliers - Hammer OWNER’S MANUAL CAUTION: Exercise of a strenuous nature as is customarily done on this equipment, should not be undertaken without first consulting a physician before beginning any exercise program. No specific health claims are made or implied as they relate to the equipment.
Page 2
Catalogue Catalogue------------------------------------------------------------------ 1 Warning-------------------------------------------------------------------- 1 Assembling steps -----------------------------------------------------2-15 Exploded view ------------------------------------------------------16-17 Parts list --------------------------------------------------------------18-22 Daily Maintenance------------------------------------------------------22 Warning 1. Before exercise, please check to make sure all bolts are tightened and handlebar welds are intact. 2. Wear appropriate footwear during work out. Do not flip the handlebars during exercise. 3.
Assembling steps 1. Remove all parts out of boxes and place around area of installation! Place bolt packs in front of the area where you want the gym. 2. Place part (2) in desired position, then connect part (3) with part (4) using bolts (M10x75mm)(13), bolts (M10x80mm)(14), washers (26) and locknuts (23).
Page 4
3. Connect backrest tube (5) to seat tube (3) with bolts (M10x75mm)(13) , washers (26) and locknuts (23). Connect tube (1) to backrest tube (5) and vertical tube (4) with (M10x75mm)(13) , washers (26) and locknuts (23).
Page 5
4. Insert leaders (10) into the oriented holes on the bottom of the curl base tube (2), in turn, slide cover bumpers (51), rubber weight stack (48) and plastic top plate (46). Mount leader top tube(6) to the leader (10) by washers (26) and bolts (M10x20mm)(5). Connect exercise chart flip (76), leader top tube (6) and Lab pull down top tube (1) with bolts (M10x75mm)(13), washers (26) and locknuts (23).
Page 6
5. Connect backrest tube (5) and chest-extension rotating frame (7) through the rotating bearing (25), tighten with Hexangular floriated bolt(M8*10mm) (30). Secure bearing bases (38), washers (26) and bolts (M10x25mm)(6). Attach chest-extension handlebars (8R&L) to the chest-extension rotating frame (7), which was already attached to backrest tube (5) in step 4, with washers (26) and bolt (M10x30mm)(7).
Page 7
6.Connect the chest-extension frame (19), backrest tube (5) and pulley fixing frame (26) with bolts (M10x70mm)(12), bolts (M10x75mm)(13), washers (26) and locknuts (23). Fit chest-extension arm (28), chest-extension adjusting board (33) to chest-extension frame (19) with locknut (24) and powder metallurgy bushing (74),flat washer(12)(33),dish washer(12)(32),nut canopy(M12)(58).
Page 8
7. Attach oriented hook (13) and zinc bushing(34)、separate ring(35) to seat tube (3) with bolt (M10x90mm)(15), washer (26), flat washer (31) and locknut (23). Attach rubber cushion (56) to the back of leg-kicking frame (39). Connect seat tube (3) and leg-kicking frame (39) with powder metallurgy bushing (70), bolt (M12x80mm)(18), washers (27) and locknut (24).
Page 9
8. Wire circling way: Cables to be installed in order cable (67) first, cable (63) second, cable (64) third, cable (66) fourth and cable (65) last. View following 5 pages for figure diagrams.
Page 10
The 1 wire: (refer to the following illustration)
Page 11
The 2 wire: (refer to the following illustration)
Page 12
The 3 wire: (refer to the following illustration)
Page 13
The 4 wire: (refer to the following illustration)
Page 14
The 5 wire: (refer to the following illustration)
Page 15
9. Attach handlebar tube (11) to the parallel bar with washer (26) and bolt (M10x20mm)(5). Attach parallel bar (20) to the vertical tube (4) with bolts (M10x75mm)(13), washers (26) and locknuts (23). Attach arm cushion (44) to the parallel bar (20) with washers (25) and bolts (M8x70mm)(8). Connect backrest cushion (41) and backrest adjusting tube (24) with washers (25) and bolts (M8x30mm)(3), then insert backrest adjusting tube (24) into backrest adjusting bushing (18), and lock it with T-shaped adjustable pin (68).
Page 16
10. Attach backrest cushion (43) to the vertical tube (4) with washers (25) and bolts (M8x20mm)(2).
Page 21
1 box of 4; box size: 1295*875*220mm PART NO. DESCRIPTION QTY. PART NO. DESCRIPTION QTY. Curl base tube Parallel bar Seat tube Chest-extension handlebar Exercise map fitch 27/29/31 Pulling bar Lab pull up top tube 2 box of 4; box size: 1965*285*220mm PART NO.