Related Manuals for Jetter JetWeb JX2-OA2
Summary of Contents for Jetter JetWeb JX2-OA2
- Page 1 JetWeb JX2-OA2 Operator’s Manual Article # 608 633 19 April 2002 / Printed in Germany...
- Page 2 JetWeb Edition 1.1 Jetter AG reserves the right to make alterations to its products in the interest of technical progress. These alterations need not be documented in every single case. This manual and the information contained herein have been compiled with due diligence.
- Page 3 This Manual is an Integral Part of the JetWeb Module JX2-OA2: Model: Serial No: Year of Manufacture: Order No: To be entered by the customer: Inventory No: Place of operation: © Copyright 2002 by Jetter AG. All rights reserved. Jetter AG...
- Page 4 Missing or inadequate knowledge of the manual results in the loss of any claim of liability on part of Jetter AG. Therefore, the operating company is recommended to have the instruction of the persons concerned confirmed in writing.
-
Page 5: Table Of Contents
JX2-OA2 Table of Contents Table of Contents Safety Instructions Ensure Your Own Safety Instructions on EMI Physical Dimensions Operating Parameters Technical Data JX2-OA2 Module - Analog Outputs Description of Connections Registers of the JX2-OA2 Module Jetter AG... - Page 6 Table of Contents JetWeb Jetter AG...
-
Page 7: Safety Instructions
Decommissioning and Disposal of the JX2-OA2 Module Decommissioning and disposal of the JX2-OA2 module are subject to the environmental legislation of the respective country in effect for the operator's premises. Jetter AG... - Page 8 · / - Enumerations are marked by full stops, strokes or scores. Operating instructions are marked by this arrow. Automatically running processes or results to be achieved are marked by this arrow. Illustration of PC and user interface keys. Jetter AG...
-
Page 9: Ensure Your Own Safety
For safety reasons, no modifications and changes to the JX2-OA2 module and its functions are permitted. Any modifications to the module not expressly authorised by the manufacturer will result in a loss of any liability claims to Jetter AG. The original parts are specially designed for the JX2-OA2 module. Parts and equipment of other manufacturers are not tested on our part, and are, therefore, not released by us. -
Page 10: Instructions On Emi
Only use metallised connectors, e.g. SUB-D with metallised housing. Please take care of direct connection of the strain relief with the housing here as well (refer to Fig. 1). Fig. 1: Shielding of SUB-D connectors in conformity with the EMC standards. Jetter AG... -
Page 11: Physical Dimensions
JX2-OA2 2 Physical Dimensions Physical Dimensions Fig. 2: Front View - JX2-OA2 Fig. 3: Side View - JX2-OA2 Jetter AG... - Page 12 JetWeb Fig. 4: Top View - JX2-OA2 Jetter AG...
-
Page 13: Operating Parameters
Shock Resistance 15 g occasionally, 11 ms, DIN EN 61131-2 sinusoidal half-wave, 2 shocks IEC 68-2-27 in all three spatial axes Degree of Protection IP20, rear: IP10 DIN EN 60529 Mounting Position Any position, snapped on DIN Rail Jetter AG... - Page 14 AM 80 % with 1 kHz Criterion A Discharge through air: DIN EN 61000-6-2 Test peak voltage 15 kV DIN EN 61131-2 (Humidity Rating RH-2 / ESD-4) DIN EN 61000-4-2 Contact Discharge: Test peak voltage 4 kV (severity level 2) Criterion A Jetter AG...
- Page 15 DIN EN 61000-4-6 AM 80 % with 1 kHz Source impedance 150 Ohm Criterion A Burst Test voltage 2 kV DIN EN 61131-2 tr/tn 5/50 ns DIN EN 61000-6-2 Repetition rate 5 kHz DIN EN 61000-4-4 Criterion A Jetter AG...
- Page 16 JetWeb Jetter AG...
-
Page 17: Technical Data
Resolution (voltage) 12 Bit Voltage Supply of Analog Outputs DC 24 V -15% through +20%, 150 mA (maximum) Output Current max. 10 mA Delay Time < 4 ms Electrical Isolation None Heat loss of CPU logic circuit 0.3 W Jetter AG... - Page 18 Output Voltage Accuracy Classes of the JX2-OA2 Module Type of Error Input Maximum Error Configuration in LSB in mV ± 6 LSB Zero Error Bipolar 29.3 mV ± 6 LSB Gain Error Bipolar 29.3 mV The typical measuring accuracy is higher. Jetter AG...
-
Page 19: Jx2-Oa2 Module - Analog Outputs
Make sure that the signal lines are shielded (see following figure) Important! The supply voltage for analog outputs must not exceed 28.8 Volt (150 mA). This will prevent the JX2-OA2 module and the actuator, possibly connected to it, from being destroyed. Jetter AG... - Page 20 5.1 Description of Connections JetWeb FWXDWRU STOP LOAD ADDRESS MODUL S6IT HIGH SER1 INPUT INPUT OUTPUT APSH@S SER2 98Ã!#ÃW 24V IO 24V CPU Fig. 5: Example: Output Wiring of a JX2-OA2 Module Jetter AG...
-
Page 21: Registers Of The Jx2-Oa2 Module
Example: Determination of the register numbers The number of the third expansion module’s register is determined as follows: Module number = 4 Local register number = 9 Register number = 3029 + (4-2) * 10 +9 = 3003 Jetter AG... - Page 22 -10 V through +10 V The voltage values are output to the actuators via output channels # 1 and 2. Example: Definition of Output Voltage Value 1534 is assigned to channel 1 (register 3yy0). The resulting voltage is 7.5 volt. Jetter AG...
- Page 23 New output voltage Value range Voltage - bipolar: -2048 ... 2047 Register 3yy9: Version Number of the Operating System Function Description Read Version number of the operating system e.g. 101= V 1.01 Write Illegal Value range 32-bit-signed integer Jetter AG...