Related Manuals for Jetter JetWeb JX2-OD4
Summary of Contents for Jetter JetWeb JX2-OD4
- Page 1 JetWeb JX2-OD4.2 Operator’s Manual Article # 608 633 21 April 2002 / Printed in Germany...
- Page 2 JetWeb Edition 1.1 Jetter AG reserves the right to make alterations to its products in the interest of technical progress. These alterations need not be documented in every single case. This manual and the information contained herein have been compiled with due diligence.
- Page 3 This Operator’s Manual is an Integral Part of the JetWeb-Module JX2-OD4.2: Model: Serial No: Year of Manufacture: Order No: To be entered by the customer: Inventory No: Place of operation: © Copyright 2002 by Jetter AG. All rights reserved. Jetter AG...
- Page 4 Missing or inadequate knowledge of the manual results in the loss of any claim of liability on part of Jetter AG. Therefore, the operating company is recommended to have the instruction of the persons concerned confirmed in writing.
-
Page 5: Table Of Contents
JX2-OD4.2 Table of Contents Table of Contents Safety Instructions Ensure Your Own Safety Instructions on EMI Physical Dimensions Operating Parameters Technical Data JX2-OD4.2 Module - Digital Outputs Description of Connections Description of LEDs Access to Inputs Jetter AG... - Page 6 Table of Contents JetWeb Jetter AG...
-
Page 7: Safety Instructions
Decommissioning and Disposal of the JX2-OD4.2 Module Decommissioning and disposal of the JX2-OD4.2 module are subject to the environmental legislation of the respective country in effect for the operator's premises. Jetter AG... - Page 8 · / - Enumerations are marked by full stops, strokes or scores. Operating instructions are marked by this arrow. Automatically running processes or results to be achieved are marked by this arrow. Illustration of PC and user interface keys. Jetter AG...
-
Page 9: Ensure Your Own Safety
For safety reasons, no modifications and changes to the JX2-OD4.2 module and its functions are permitted. Any modifications to the module not expressly authorised by the manufacturer will result in a loss of any liability claims to Jetter AG. The original parts are specially designed for the JX2-OD4.2 module. Parts and equipment of other manufacturers are not tested on our part, and are, therefore, not released by us. -
Page 10: Instructions On Emi
Only use metallised connectors, e.g. SUB-D with metallised housing. Please take care of direct connection of the strain relief with the housing here as well (refer to Fig. 1). Fig. 1: Shielding of SUB-D connectors in conformity with the EMC standards. Jetter AG... -
Page 11: Physical Dimensions
JX2-OD4.2 2 Physical Dimensions Physical Dimensions Fig. 2: Front View - JX2-OD4.2 Fig. 3: Side View - JX2-OD4.2 Jetter AG... - Page 12 JetWeb Fig. 4: Top View - JX2-OD4.2 Jetter AG...
-
Page 13: Operating Parameters
Shock Resistance 15 g occasionally, 11 ms, DIN EN 61131-2 sinusoidal half-wave, 2 shocks IEC 68-2-27 in all three spatial axes Degree of Protection IP20, rear: IP10 DIN EN 60529 Mounting Position Any position, snapped on DIN Rail Jetter AG... - Page 14 AM 80 % with 1 kHz Criterion A Discharge through air: DIN EN 61000-6-2 Test peak voltage 15 kV DIN EN 61131-2 (Humidity Rating RH-2 / ESD-4) DIN EN 61000-4-2 Contact Discharge: Test peak voltage 4 kV (severity level 2) Criterion A Jetter AG...
- Page 15 DIN EN 61000-4-6 AM 80 % with 1 kHz Source impedance 150 Ohm Criterion A Burst Test voltage 2 kV DIN EN 61131-2 tr/tn 5/50 ns DIN EN 61000-6-2 Repetition rate 5 kHz DIN EN 61000-4-4 Criterion A Jetter AG...
- Page 16 JetWeb Jetter AG...
-
Page 17: Technical Data
Load current max. 2 A per output Output power of outputs 384 W Electrical Isolation None Protective circuit Short circuit, overvoltage, overtemperature Protection against inductive loads Principle of Operation Non-latching Signal voltage ON typ. V -1.5 V Supply Jetter AG... - Page 18 When removing or inserting the module, the supply lines as well as the signal lines must be de-energised. Otherwise the JX2-OD4.2 module will be destroyed. Caution A digital output may directly (without additional load) be connected to a digital input. Note! Jetter AG...
-
Page 19: Jx2-Od4.2 Module - Digital Outputs
The maximum stripping length for input lines is 7 mm • The accepted VDE guidelines have to be observed • Flat-bladed screwdriver: 0.6 x 3.5 x 100 mm Connecting Cable Specifications • Not required Cable Shielding • Not required Jetter AG... -
Page 20: Description Of Leds
5.2 Description of LEDs JetWeb ; 75$16 )250(5 '& 9 $FWXDWRU Fig. 5: Example: Output Wiring of a JX2-OD4.2 Module Description of LEDs The LEDs show that a 24 V output signal is applied to the corresponding output. Jetter AG... -
Page 21: Access To Inputs
Basic Output Input Input Controller Module Module Module Module # 1 Module # 2 Module # 3 Module # 4 Inputs and Outputs Output Input Input 101 .. 108 201 .. 208 301 .. 308 401 .. 408 Jetter AG... - Page 22 ! ! ! ,QSXW Inputs and Outputs Output SV-Module 101 .. 108 201 .. 208 301 .. 308 Note! From example 2 can be seen that module JX2-SV1 is not taken into account when numbering digital inputs and outputs. Jetter AG...