Wall Mounting; Structure Or Fixed Sun Umbrella Installation; Installation Directly On The Ceiling (Fig. 4/7) - S&P HE-N Series Manual

tion should be when children and vulnerable people are present.
• Do not clean the appliance when in operation and do not immerse it in water.
• Do not manipulate the appliance with wet hands.
• Do not wrap the power cable round the appliance while it is in operation.
• If the cable is damaged it must be replaced; do not do this yourself take the appliance to an
authorised repair centre, as this operation must be carried out by specialised personnel to avoid
hazards or damage.
• Do not use the appliance as a clothes or towel drier.
• This heater is not equipped with a device of room temperature control. Do not use this heater in
small rooms that are occupied by people who can not leave the room by themselves, unless on
going monitoring is assured.
• Only for external use.

3. WALL MOUNTING

Before starting to install the appliance, carefully read the Safety warnings indicated in the section 2.
Before starting to install the appliance, make sure that once installed, the minimum security distances indicated in the Fig. 2 will
be met.
• Using the orientable support of the same device as a template, mark 4 holes in the wall.
Use one level tool to ensure the support is completely horizontal (Fig. 5)
• Do 4 holes in the wall using a 8 mm diameter drill bit. Insert the 4 screws with metal rods (Fig. 1C).
• With the supplied wrench (Fig. 1B), remove the 4 nuts and washers and fi x the appliance on the wall.
• Once fi xed, and with supplied hex key (Fig. 1D), loosen the screw indicated in the Fig. 6 to orientate the appliance to its right
measure.
• Once installation is fi nished, be sure that device is completely horizontal with help of level tool; verify that power supply cable is
not in contact with body or in front of frontal lamp grille.

4. STRUCTURE OR FIXED SUN UMBRELLA INSTALLATION

Before starting to install the appliance, carefully read the Safety warnings indicated in the section 2.
Before starting to install the appliance, make sure that once installed, the minimum security distances indicated in the Fig. 3 will
be met.
• To fi x the appliance in a metal structure or fi xed sun umbrella, universal support provided can be used (Fig. 1 E)
Attention: Provided universal support, can be coupled to a metal structure/ fi xed sun umbrella, if the support has dimensions
of thickness: 20x20 mm minimum/ 40x40 maximum.
• Using 4 screws and 4 nuts (Fig. 1H), joint the universal support (Fig. 1E) to the adjustable support of the same appliance. Then
attach the assembly to the structure/ fi xed sun umbrella as indicated in the Figure 8.
• Using the two hex screws (Fig. 1G) and the fi xed bolt (Fig. 1F) will prevent the device is moved or fall down accidentally (Fig. 8).
• To avoid scratching the paint on the structure/ fi xed sun umbrella, you can put the supplied protective mat (Fig. 1 I)
• Once fi xed, and with supplied hex key (Fig. 1D), loosen the screw indicated in Fig. 6 to orient the appliance to its right measure.
• Once installation is fi nished, be sure that device is completely horizontal with help of level tool; verify that power supply cable is
not in contact with body or in front of frontal lamp grille.

5. INSTALLATION DIRECTLY ON THE CEILING (FIG. 4/7)

Before starting to install the appliance, carefully read the Safety warnings indicated in the section 2.
Before starting to install the appliance, make sure that once installed, the minimum security distances indicated in the Fig. 4 will
be met.
• Depending on the ceiling where you want to fi x the appliance, you must select the most appropriate type of fi xation. Direct fi xing
to the ceiling is not supplied with the appliance.
• Remove the two screws located on the back of the metal body, which act as a plug (Fig. 4) and screw the metal cables with
supplied security retainers.(Fig. 1J)
• Adjusting the useful length of the metal cable, you can adjust the fi nal height of the appliance (Fig. 7)
• Once hung, close the security retainers to prevent the unit is picked up or accidentally dropped.
• Once the installation is fi nished, use a level to ensure that the appliance is completely horizontal, that the power supply cable
does not touch the body of the appliance or is in front of the lamp grid.
12