AAT SOLO User Manual
Hide thumbs
Also See for SOLO:
- User manual (84 pages) ,
- Original user manual (16 pages) ,
- Translation of the original user manual (24 pages)
Related Manuals for AAT SOLO
Summary of Contents for AAT SOLO
- Page 1 BLACK EDITION Translation of the original user manual 2019-10 (3.1)
- Page 2 „ Spare parts „ Show room & exhibition devices With our professional service concept „ Repairs processing „ Re-use AAT proves once again its high claim of quality and offers its clients an all-inclu- „ Technical advice „ Complaints sive package.
- Page 3 (Managing Director) WARNING Failure to observe this user manual, in particular the safety instructions, can lead to defects in the SOLO and endanger the user and persons in the immediate vicinity of the device. There is an increased risk of injury! In the event of an infringement, claims for warranty and liability are excluded! SOLO has been successfully tested by TÜV Süd Product Service GmbH in Hanover according to DIN...
-
Page 4: Table Of Contents
Technical data SOLO ........ -
Page 5: Symbols And Safety Instructions
Stability tests were performed under laboratory conditions. SOLO can behave differently under real conditions compared to laboratory tests. Training may only be carried out by the manufacturer, the AAT field staff or the qualified specialist shop. CAUTION External heat sources may cause the surface temperature to rise (e.g. sunlight)! -
Page 6: Explanation Of The Symbols On The Packaging
To avoid being crushed, never reach into rotating/moving parts! DANGER SOLO must not be operated in the case of severe visual impairment and/or blindness! Do not exceed the total permissible weight and the maximum person weight, as this may lead to... -
Page 7: Explanation Of The Symbols On The Device
CE mark The product complies with the relevant provisions of EC Directives 2006/42/EC, 2007/47/EC und 93/42/EC Serial number of the product e. g. SOLO = T1601XXXXXX / SOLO = T2001XXXXXX Note on the user manual The user manual must be observed! www.aat-online.de... -
Page 8: Product Description
Product description 4.1 Device overview SOLO / SOLO Manufacturer’s information: For a simplified assignment of the individual components, the numbers listed here are cited in full for the first time in the follow- ing chapters. Interface Battery pack (Lithium-ion or lead-gel) - Page 9 Operating unit Horn Speed selection fast Joystick Display Hand rest Speed selection slow ON/OFF Drive wheels Plug-in contact Latch Mounting bolt Coupling disk Release...
-
Page 10: Indication And Intended Use
The SOLO transport device is also equipped with an operating unit that can be used by an accompanying person. This feature is important when the wheelchair user is no longer able to move around themselves using the joystick and the accompanying person’s own strength does not allow them to push a wheelchair... -
Page 11: Technical Data Solo
4.4 Technical data SOLO WARNING - Do not exceed the total permissible weight and the maximum person weight, as this may lead to defects or an overloading of SOLO! NOTE - Observe the technical data. SOLO Technology Lithium ion (ALPHA Box) Lead gel (BETA Box) Height = 191 mm;... -
Page 12: Technical Data Solo
4.5 Technical data SOLO WARNING - Do not exceed the total permissible weight and the maximum person weight, as this may lead to defects or an overloading of SOLO NOTE - Observe the technical data. Technology SOLO incl. lithium-ion battery pack (ALPHA Box) Height = 191 mm;... -
Page 13: Dimensional Drawing
4.6 Dimensional drawing +30 mm +30 mm 4.7 Scope of delivery Drive wheels Battery pack (lithium-ion or lead-gel) Operating unit with operating unit holder Battery bag incl. Velcro tapes Charger... -
Page 14: Accessories
4.8 Accessories NOTE - Only use AAT Alber Antriebstechnik GmbH accessories. Bracket Anti-tip supports Spoke protector Vehicle voltage converter 12 V / 230 V Battery pack (additional) Attendant control SmartControl Accessories for the operating unit Therapy tray installation Soft ball... -
Page 15: Assembly And Start-Up
Assembly and start-up 5.1 Drive wheels CAUTION – Plug-in contacts must be dry! CAUTION – Drive wheels must be disengaged for assembly and start-up! (see chapter 6.6) If the wheelchair still has the original wheels on, then remove them first. Lift wheelchair Hook the holding fixture... -
Page 16: Battery Pack
5.2 Battery pack WARNING - Never short-circuit or connect the poles of the battery pack to avoid electric shocks! CAUTION - Plug-in contacts must be dry! Setting the driving mode (pictures 1 - 3, only for lithium-ion battery pack) Setting the driving mode – Turn and insert the safety Tighten the screws. -
Page 17: Operating Unit
WARNING - Never use without both anti-tip supports to prevent the wheelchair from tipping backwards! WARNING - Check the anti-tip supports before initial operation to ensure safety! If anti-tip supports are not available on your wheelchair, use AAT anti-tip supports in pairs! Observe ‘R’... -
Page 18: Start-Up
Start-up DANGER - Operation only by a single, trained person. This person must be physically and mentally able to safely operate SOLO and may not suffer from cognitive impairments! DANGER – Never use without both anti-tip supports to prevent the wheelchair from tipping backwards! DANGER –... -
Page 19: Engaging Drive Wheels
= Disengaged. place. Repeat on the other side. 6.2 Switching on SOLO switches on. Warning: Please only turn on the SOLO once the passenger is seated. 6.3 Display indicators Start display. Standard display. Immobiliser. » Battery pack capacity... - Page 20 Warning notice Warning notice Warning notice Wheel lock Wheel lock Wheel lock Both wheels Left wheel Right wheel Warning notice Warning notice Warning notice Coupling disk Coupling disk Coupling disk Both wheels Left wheel Right wheel Warning notice Warning notice Warning notice Undervoltage Overvoltage...
- Page 21 Warning notice Warning notice Stand-up function Temperature Temperature Battery pack Drive wheels Download parameters Battery pack is charging Error messages (see chapter 10.2) Battery pack Drive wheels Operating unit...
-
Page 22: Driving With Solo
NOTE - Please refer to the chapter on warning notices, error messages and troubleshooting! NOTE - Display lighting switches off if the operating unit has not been used for 20 seconds. NOTE – Automatic switch-off switches off the SOLO after 10 minutes when paused for longer periods. -
Page 23: Overcoming Obstacles
» SOLO switches off. Emergency stop function When you let go of the joystick the SOLO stops automatically on the flat surface within 1 meter depending on the weight of the transported person, the ground, the terrain profile, etc. If the ON/OFF button is pressed and held down while driving, the SOLO switches off completely (without displaying a warning message beforehand). -
Page 24: Manual Driving With Quick-Release Wheels
6.7 Manual driving with quick-release wheels CAUTION – Risk of crushing between tyre and side panel/armrest! Switch off SOLO. Disassemble drive wheels. Assemble quick-release (see chapter 7) wheels. Observe pictures 4 - 6! Press the release button for Adapt wheel. -
Page 25: Disassembly
Disassembly Remove drive wheels Flip the release Turn the release. Remove the drive wheel. Repeat process on the other side. Remove the operating unit Carry out the steps listed in chapter 5.4 in reverse order. Remove the battery pack Carry out the steps listed in chapter 5.2 in reverse order. Please note that the flight mode (crossed-out flash) is set for the lithium-ion battery pack. -
Page 26: Transport
Transport WARNING – Do not use SOLO with wheelchair as a seat in a vehicle! WARNING – Secure according to valid statutory provisions during transport in vehicles/aeroplanes! CAUTION – Switch off during transport! CAUTION – Observe the vehicle’s weight specifications! NOTE –... -
Page 27: Battery Pack And Charger
NOTE – Store the battery pack in a frost-free environment at least one hour prior to start-up to avoid malfunctions. Manufacturer's information: The battery pack is maintenance-free and rechargeable. New batteries only reach their full capacity after several charging cycles. During the charging process, SOLO cannot be operated. Charge battery pack Disable SOLO (see chapter 6.8). - Page 28 Charging the lithium-ion battery pack If required, unplug the interface. The battery pack can stay in Connect the charger. the battery bag when being » Plug the charger connector charged. into the charging port of the battery pack. LED green = battery full approx.
- Page 29 Charging the lithium ion battery pack in a motor vehicle Unplug the interface. Remove the battery pack. Connect voltage transformer » Open Velcro and remote and charger. battery pack. » Connect charger to battery pack. Switch on the voltage LED green = battery full LED orange = battery is converter.
- Page 30 Charging the lead gel battery pack required, unplug interface. The battery pack can stay in Connect the charger. the battery bag when being » Fully insert the charger charged. connector into the battery pack jack. LED green = battery full approx.
- Page 31 Charging the lead gel battery pack in a motor vehicle Unplug the interface. Remove the battery pack. Connect voltage transformer » Open Velcro and remote and charger. battery pack. » Connect charger to battery pack. Switch on the voltage LED green = battery full LED orange = battery is converter.
-
Page 32: Cleaning
WARNING – Test all safety-relevant functions after cleaning! WARNING – Do not smoke during cleaning! NOTE – Keep SOLO away from sources of ignition! NOTE – Clean the drive unit, tooth segments and drive shafts in the event of dirt/deposits! NOTE –... -
Page 33: Disposal
– dispatch may only take place via authorised dealers! (regulation only for the lithium-ion battery pack) Your SOLO and its batteries are durable products. After expiry of the natural service life, you can return these components to AAT Alber Antriebstechnik GmbH or their specialist dealers for disposal. -
Page 34: Long-Term Storage
9.4 Long-term storage If SOLO is not used for an extended period of time (e.g. over several months), observe the following information: • Observe the wheelchair manufacturer’s information if the wheelchair is to be stored! • No moisture must be allowed to enter the interior of the device! •... -
Page 35: Reuse (Change In Operator)
9.6 Reuse (change in operator) The term reuse is used when the AAT product of patient X is to be used for another patient Y. In addition, there is a reuse when a patient receives a different wheelchair and therefore requires new add-on parts. -
Page 36: Warning Notices, Error Messages And Troubleshooting
10 Warning notices, error messages and troubleshooting 10.1 Warning notices Wheel lock Left drive wheel Right drive wheel Both drive wheels » Wheel and left arrow flash! » Wheel and right arrow flash! » Wheel and both arrows » Adapt the wheel correctly »... - Page 37 Temperature drive wheels Stand-up function » Battery flashes! » Wheel flashes! wheelchair » Stop driving with SOLO and » Stop driving with SOLO and » Arrow flashes! let it cool down. let it cool down. » Change the wheelchair to...
-
Page 38: Error Messages
Switch off SOLO, wait 10 seconds, switch on SOLO! Does the error still exist? Parameter data Yes: Notify the manufacturer, the AAT field staff and the authorised spe- cialist dealer! Switch off SOLO, wait 10 seconds, switch on SOLO! Does the error still exist? -
Page 39: Troubleshooting
(bicycle accessory). Do not use a screwdriver or any other sharp object as a lever! NOTE – the air pressure for the tyres is displayed on both sides of the tyre. If you have any questions, contact the manufacturer, the AAT field team or the autho- rised specialist dealer! -
Page 40: Guarantee And Liability
SOLO beyond the total permissible weight. • improper charging of the battery pack. Liability As the manufacturer of SOLO, AAT Alber Antriebstechnik GmbH is not responsible for any damages that may result if: • SOLO was improperly handled. - Page 41 Notizen...
- Page 42 Notizen...
- Page 43 Notizen...
- Page 44 AAT Alber Antriebstechnik GmbH Postfach 10 05 60 · 72426 Albstadt · Germany Phone: +49 (0) 74 31 12 95-0 Fax: +49 (0) 74 31 12 95-35 info@aat-online.de · www.aat-online.de Serial number:...