Related Manuals for Belden grass valley NV9646
Summary of Contents for Belden grass valley NV9646
- Page 1 NV9646 NV9000 CONTROL PANEL User’s Guide VERSION 1.0 UG0080-00 2015-07-02 www.grassvalley.com...
- Page 2 Copyright and Trademark Notice Copyright © 2015, Grass Valley USA, LLC. All rights reserved. Belden, Belden Sending All The Right Signals, and the Belden logo are trademarks or registered trademarks of Belden Inc. or its affiliated companies in the United States and other jurisdictions.
- Page 3 NV9646 User’s Guide Electrostatic Discharge (ESD) Protection Electrostatic discharge occurs when electronic components are improperly handled and can result in intermittent failure or complete damage adversely affecting an electrical circuit. When you remove and replace any card from a frame always follow ESD-prevention procedures: •...
- Page 4 Notices immédiatement à l'eau savonneuse. Ne jamais ingérer le liquide. La toxicité est extrêmement faible, mais la prudence demeure de mise en tout temps. Recycling Visit www.grassvalley.com for recycling information. Certification and Compliance Safety Compliance This equipment complies with the requirements of CSA/UL/IEC/EN 60950-1, 2 Ed.
-
Page 5: Table Of Contents
Table of Contents 1 Preface ..........1 Chapter Structure . - Page 6 Table of Contents Selection Buttons ..............39 Scrolling .
- Page 7 NV9646 User’s Guide Clear Preset ............. .61 Default State .
- Page 8 Table of Contents 6 GPIO..........81 The Interface .
-
Page 9: Preface
Preface Chapter 1 is an introduction to the NV9646 User’s Guide. Summary Chapter Structure ..............1 The PDF Document . -
Page 10: Terms, Conventions And Abbreviations
Preface Terms, Conventions and Abbreviations Use the ‘First Page’ , ‘Previous Page’ , and ‘Next Page’ , and ‘Last Page’ buttons to go to the first, previous, next, or last page within a PDF file. Note: To display the navigation buttons, right-click the Tool Bar area, and check ‘Navigation’ . Use Acrobat’s extensive search capabilities, such as the ‘Find’... -
Page 11: Introduction
Introduction Chapter 2 provides a basic functional description of the NV9646. Summary Summary ................3 Panel Organization . -
Page 12: Panel As Nv9642 Extension
Introduction Panel as NV9642 Extension At the rear, in addition to power, serial, and network connectors, is a 25-pin GPIO (i.e., tally) connector that supports 4 optically isolated relay outputs and 8 optically isolated inputs: Ethernet Power (2) Serial (RS-232) GPIO (tally) Fig. -
Page 13: Alphanumeric Display
NV9646 User’s Guide brightness and low tally can be either low or medium brightness. High tally is always constrained to be brighter than low tally. We say a button is “dark” when its LCD is turned off. See Buttons, page 93, for a color chart. Although you can see a list of the pages in the tree during configuration, the structure of the tree is not evident on the panel itself. -
Page 14: Display Fields
Introduction Alphanumeric Display multi-destination. The display changes according to those modes. This is an example for X/Y mode: PRESET PRESET STATUS STATUS LVL/DST LVL/DST - - S S - - I I - - L L - - B B PAGE X - Y VTR--4... - Page 15 NV9646 User’s Guide In X-Y mode, the preset column represents the levels of a source or the levels of multiple sources under breakaway. These are called the preset source(s). After the take, they disappear from the preset column and re-appear in the status column, reflecting that the preset sources have now become current sources.
-
Page 16: Tally Interface
Introduction Tally Interface level is not a breakaway level. In MD mode, an asterisk indicates a breakaway on the associated destination. The display fields can show either names from a name set or system mnemonics for devices depending on (1) the state of the ‘Name Set Toggle’ button (if the panel has one), (2) the default name set (3) the existence of name sets in the NV9000 configuration. -
Page 17: Other Nv9646 Functions
NV9646 User’s Guide The secondary modes of panel operation are: • Setup mode — where the NV9646 is freshly powered up, but disconnected from the network. In this mode, you can preset the NV9646’s panel ID and perform a few diagnostic tasks. - Page 18 Introduction Other NV9646 Functions...
-
Page 19: Installation
Installation Chapter 3 provides installation and connection instructions. Summary Package Contents ..............11 Installation . -
Page 20: Installation
Installation Installation Installation Follow these steps to install a NV9646 control panel: 1 Mount, and secure, the panel in the rack. The NV9646 is designed to mount in a 19 in rack. Rack-mounting is not a requirement. Place the panel in position in your rack. Attach the panel to the rack frame, using screws appropriate for your rack. -
Page 21: Initialization
NV9646 User’s Guide Initialization Before your NV9000 system controller can communicate with an NV9646, you must give it a panel ID. Follow these steps for each NV9646 you are installing: 1 Power up the NV9646. Do not connect its Ethernet cable. (Disconnect it if it is connected.) After a few seconds, the alphanumeric display will show ‘No Server’... -
Page 22: Testing
Installation Testing Testing As shown above in step 3, a panel test function is available when the NV9646 is disconnected from the system controller. The test determine the “health” of the buttons of your NV9646. See Setup Mode on page 79 for detail. Press the ‘Software Versions’ button to review the versions of installed software and firmware. -
Page 23: Configuration
Configuration Chapter 4 provides configuration instructions for the NV9646. Summary Summary ................15 Adding a Panel to an NV9000 Configuration . -
Page 24: Adding A Panel To An Nv9000 Configuration
Configuration Adding a Panel to an NV9000 Configuration Adding a Panel to an NV9000 Configuration You must create configurations for the NV9646 using NV9000-SE Utilities. We assume that you are familiar enough with NV9000-SE Utilities that you can understand the following material. - Page 25 NV9646 User’s Guide Choose “NV9646” from the ‘Type’ field. In the ID field, enter the panel ID you assigned to the panel while it was in setup mode. Give a name to the panel in the name field and select a user.
-
Page 26: Nv9646 Panel Configuration Page
Configuration NV9646 Panel Configuration Page NV9646 Panel Configuration Page This is the default NV9646 panel configuration page in NV9000-SE Utilities: Panel Image Button Definition Section Panel Options Button Page Table GPIO Definitions Fig. 4-1: NV9646 Configuration Page (Panel and Buttons Mode) Similar pages exist for NV9646 suffix templates and global navigation templates. -
Page 27: Regions Of The Configuration Page
NV9646 User’s Guide The previous illustration showed the configuration page set up for ‘All Buttons’ mode. The panel can also be configured in ‘Display and Buttons’ mode, in which case the “display” section of the button matrix is delineated by a white line on the page: Fig. -
Page 28: Configuration Tasks
Configuration Configuration Tasks • Button page table. This section — the region below the button definition section — displays a list of the individual pages of the tree structure. The button page at the top of the list (or root of the tree) is called “Default. -
Page 29: Commitment Buttons
NV9646 User’s Guide The panel operator, in most cases, needs a ‘Take’ button and at least one selection button. In addition to their basic function, selection buttons provide feedback about the preset source device and level mapping. A ‘Clear Preset’ button is strongly recommended. Commitment Buttons Two buttons at the bottom of the configuration page are self-explanatory and present on most configuration pages:... - Page 30 Configuration Panel Options Release Mode Normal Release This panel can release “locks” and “protects” set by the designated user (at this panel or any other panel). Force Release This panel can release locks and protects set by any user. Default None After a reset, the panel displays no destination device.
- Page 31 NV9646 User’s Guide MD Data Automatic If a machine control (i.e., data) level is involved in a route, the Routing Mode system makes the route on the control level even if the control port is in use on the source or destination device. It breaks the previous control connection and then makes a new control connection for the route in progress.
-
Page 32: Checkbox Options
Configuration Checkbox Options Checkbox Options The checkbox options section is at the bottom of the panel options section: A check in the box enables the option. Clearing the checkbox disables the option. By default, all the check box options are unchecked except ‘Src/Dst Immediate Take’ . That particular option is enabled by default. - Page 33 NV9646 User’s Guide Check ‘Enable Destination Protect’ so that any ‘Destination Protect’ button on the panel will function. • Source Master Default. Makes a control-level source the controlling device (or master device) by default. Otherwise, the destination is the master by default. (The option is specifically for use with NV9000 series machine control routers.) “Source is master”...
-
Page 34: Button Definitions
Configuration Button Definitions the box is clear, the button sets up the preset and the operator must press a ‘Take’ button to complete the take. • Page VFD only. The panel pages the display (here called a VFD) only and does page selection buttons. -
Page 35: Button Specification
NV9646 User’s Guide Button Specification The button definitions section has several controls: The controls vary according to the button type. Button Type A pull-down menu where you may select a button type. Button Caption Three text boxes in which you can enter three lines of button text up to 8 characters each. -
Page 36: Button Types
Configuration Button Types name and destination name as text. The option, when checked, over- rides the default. Be careful: unchecking this box alters the text you entered. When you choose a button type, additional drop-down menus can appear, depending on the button type, allowing you to further specify the button’s behavior. - Page 37 NV9646 User’s Guide Type Description Category Displays a category’s device list. When you assign a category button, two additional drop-down menus appear: ‘Src Category’ and ‘Dst Category’ . Choose a category from one of the category lists. When you choose a source category, the destination categories become inaccessible and vice versa: a category button must be either a source category or a destination category.
- Page 38 Configuration Button Types Type Description Destination Sets or removes a “protect” on the current destination device. The protect Protect can be removed only by the user that originally set the protect, or by a panel that has “Force Release” enabled. Note: a protect prevents others from routing to a destination;...
- Page 39 NV9646 User’s Guide Type Description Menu This button puts the NV9646 panel in menu mode and displays a menu on the LCD buttons that provides access to a variety of panel options. Place the button on the panel only if you want the user to have access to the menu. By pressing certain buttons, the user makes menu selections and may enter data (such as panel ID) or change LCD brightness values.
- Page 40 Configuration Button Types Type Description Panel Lock Prevents accidental changes to the panel settings, especially router crosspoints. When the panel is locked, the button array becomes blank except for the Panel Lock button which becomes high tally red. Pressing the Panel Lock button again reverts the panel to its previous mode.
- Page 41 NV9646 User’s Guide Type Description Selection Typically, at least one button page should provide a set of selection buttons. Operators press selection buttons to select levels (when the panel is in XY mode) or to select MD device (in MD mode). Each selection button represents one level or one MD device.
- Page 42 Configuration Button Types Type Description Source A source button selects a source. (Note that a quick source button selects a source and also performs an immediate take.) When you assign a source button, a drop-down menu appears: ‘Source Device’ . Choose a device from the list. (The ‘None’ entry is merely a placeholder.
-
Page 43: Edit Navigation Button' Dialog
NV9646 User’s Guide Type Description X-Y Display This button displays the current source and current destination. It is usable in both X/Y mode and MD mode. It is very useful when the panel has no display. It might be appropriate to define an ‘X-Y Display’ button in the display area. When the display is turned off, the button would become visible. - Page 44 Configuration ‘Edit Navigation Button’ Dialog The button caption is independent of the page name. You can change either without affecting the other. The dialog has 3 navigation choices: • Jump to an empty new page. This option creates a new page in the button tree. During operation, the navigation button you are creating will cause the NV9646 to display, or jump to, that page.
-
Page 45: Automatic Fill Options
NV9646 User’s Guide Automatic Fill Options • Source Devices SE assigns sources to buttons in new button subpage(s). If it has too many sources to fit on the subpage, it creates further subpages as needed. The software adds ‘Back’ and ‘Forward’... -
Page 46: Button Page List
Configuration Button Page List buttons are labeled with the category names. You can edit the button captions. The software adds ‘Back’ and ‘Forward’ buttons when more than one subpage is required. Categories that are both source and destination categories are included. •... -
Page 47: Tally (Gpio) Window
NV9646 User’s Guide You can change the name of a page by double-clicking the page’s name field and editing its text. Changing the name of a page does not cause a change to the caption of the navigation button and vice versa. During configuration, you will use ‘Navigate’... -
Page 48: Scrolling
Configuration Scrolling You should configure at least one selection button (for feedback). You may configure as many selection buttons as are suitable for your system. For instance, if your system has a maximum of 12 levels for any device, it might make sense to have 12 selection buttons. Operators can scroll through multiple pages of levels in X-Y mode and through multiple pages of devices in MD mode. -
Page 49: Selection Button Behavior
NV9646 User’s Guide In ‘Display and Buttons’ mode, if the operator turns off the display, it nevertheless scrolls (or not) as it would if it were visible. When the operator turns the display on again after scrolling, it reappears correctly. Selection Button Behavior XY Mode When the panel is in XY mode, a set of selection buttons presents a set of virtual levels. -
Page 50: Xy Mode - Hold Mode
Configuration Display Indexes Note that if the operator selects a level when all levels are on, all the other levels become unselected (low-tally). Selecting a new destination again turns on all selection buttons that have levels defined. Source/Destination buttons are “all level”— not subject to level selection. XY Mode —... -
Page 51: Single-Destination Mode
NV9646 User’s Guide Single-Destination Mode Single-destination mode (a.k.a. “single-bus” or “button-per-source” mode) can be emulated in either X-Y mode or MD mode. Single-destination mode is not a distinct mode. It can be blended with either of the other two modes. You can create many different forms of “single-destination” mode. This mode need not have just one destination. - Page 52 Configuration How to Configure MD Devices 3 Click ‘Edit Multi-Dest Devices’ . The multi-destination entry editor appears: On the left is a list of all destinations defined in the NV9000 system. On the right is a table of the MD destinations you are defining. The number of rows in this table is equal to the maximum number of MD destinations your configuration allows.
-
Page 53: Md Destination Options
NV9646 User’s Guide MD Destination Options On the right side of the multi-destination entry editor, each MD destination has two checkboxes. One is in the ‘User Definable’ column and the other is in the ‘User Selectable’ column. User-Definable When the MD destination is “user definable, ” the operator may choose a different destination using the panel buttons. -
Page 54: Names
Configuration Names Names After adding global navigation templates to your N9000 configuration, you will see them identified as such in the control panel list: Navigation Template Suffix Template The words “Navigate” and “Suffix” appear in the ‘Panel Type’ and ‘Configuration Name’ columns. -
Page 55: Referencing A Navigate Template
NV9646 User’s Guide The suffix page is a copy of the suffix template. It is not the template or a link to the template. Category buttons in the panel configuration that reference a suffix template do have links to their templates. ... -
Page 56: Composing Suffix Templates
Configuration Composing Suffix Templates The global navigation template provides all the button types available for panel configurations except additional ‘Global Navigate’ buttons. Other than that, a global navigation page is functionally identical to any ordinary button page. A global navigation page should at least have a back button. Composing Suffix Templates Suffix templates have only a few button types. -
Page 57: Composing Navigate Templates
NV9646 User’s Guide If you make a change to a suffix template and it is in use by one or more panel configurations, you will want to click ‘Push changes to panel configs’ . You can see the panel configurations in the list under ‘Panel References’: List of panel configuration pages that use this suffix template... - Page 58 Configuration Composing Navigate Templates When you click ‘Push changes to panel configs’ , the configuration software adjusts all panel configurations to use the modified navigate template. If you want to update the global navigation page in only some of your panels, create an alternate version of your navigate template and change the panel configurations to use one or the other as desired.
-
Page 59: Operation
Operation Chapter 5 provides operating instructions for the NV9646 control panel. Summary Summary ................51 Operating Concepts . -
Page 60: Modes Of Operation
Operation Modes of Operation • Virtual level selection buttons (in X-Y mode) or MD device selection buttons (in MD mode). • Status of preset and current sources and the selected destination(s). At any particular time, some of the buttons are enabled or disabled. Some are high-tally; some are low-tally;... -
Page 61: Behavioral Models
NV9646 User’s Guide Behavioral Models The panel has two behavioral models: ‘All Buttons’ mode and ‘Display and Buttons’ mode. In ‘Panel and Buttons’ mode, the panel emulates an “alphanumeric display” using the characters on the left-most 5×2 array of buttons. In this mode, users can turn the display on or off, as needed. - Page 62 Operation Levels on Selection Buttons buttons. For instance, if there are 5 selection buttons on the page, they scroll in groups of 5 levels. The display shows up to 5 levels at a time, as determined by the current destination: PRESET PRESET STATUS...
-
Page 63: Level Mapping
NV9646 User’s Guide default name set (3) the existence of name sets in the NV9000 configuration. (An “alias” is a name defined in a name set.) Any button page may have one or more selection buttons. The number of buttons on the page is not important unless your panel is configured so that its display and selection buttons scroll together. -
Page 64: Lists
Operation Lists If the panel has a ‘VFD/SEL Toggle’ button, you can switch between options 1 and 2. The button will read either “Paging VFD Display” [sic] or “Paging Select Buttons. ” When you page up or page down through MD devices on the selection buttons, the MD devices scroll on the selection buttons visible on the current button page, modulo the number of buttons. -
Page 65: Operating Concepts
NV9646 User’s Guide Levels or MD devices presented on the display are also considered lists, but these lists are different from, say, salvo lists. To scroll through lists of levels or MD destinations, use the ‘Page Up’ and ‘Page Down’ buttons. Operating Concepts Status for most or all operations is presented on the alphanumeric display if it is present and turned on (and occasionally on certain buttons). -
Page 66: Hold
Operation Hold The NV9646, at present, ignores the concept of level groups, and presents any config- ured level groups as completely expanded. That is, it always displays basic levels and never abstract levels. Hold Hold mode (and hold buttons) apply in both X-Y mode and multi-destination mode. Breakaway In X-Y mode, a hold button retains breakaway levels after a take. -
Page 67: Buttons
NV9646 User’s Guide At this point, you could press a ‘Clear Preset’ button — on the suffix page with the keypad — to erase the digits or suffixes you entered. ‘Clear Preset’ does not return to the previous page but allows you to re-enter digits or suffixes. 4 When you have the desired source selected, press a ‘Back’... -
Page 68: Broadcast
Operation Buttons Broadcast A broadcast button applies to a machine control level only. The button assigns one controlling device (the master) to multiple controlled devices (the slaves). The function is useful in dubbing applications. See Broadcast Routes on page 75 for more information. ... -
Page 69: Chop
NV9646 User’s Guide Chop When a “chop” function is supported by a router, the button is a toggle that enables and disables “chop. ” Chop is a rapid switching of the selected destination device between the current source and the preset source. The chop function is used to test system timing and would not be used during normal operation. -
Page 70: Destination Protect
Operation Buttons MD Mode In MD mode, a locked destination has an “L” in the “L” column when it appears in the panel’s display. When you select a locked MD destination with a button, the ‘Destination Lock’ button goes high-tally. The ‘Destination Lock’... -
Page 71: Free Source
NV9646 User’s Guide Free Source This button selects a phantom device that can be used to release or “free” devices on the machine control level. A free source can also be used with tielines to free the tieline for others to use. Use the button as if it were a source. -
Page 72: Level Map
Operation Buttons The default button text is “Info” but the button can have any legend. Level Map The ‘Level Map’ button cross-connects levels (typically in the same physical router). The function is typically used to shuffle audio channels, for example, to connect AES1/2 to AES3/4. -
Page 73: Menu
NV9646 User’s Guide 4 At this point, the level mapping is complete. The display shows an asterisk in the “I” column indicating that you can view details about the level using an ‘Information’ button: X - Y PRESET PRESET STATUS STATUS LVL/DST LVL/DST... -
Page 74: Navigate
Operation Buttons The panel requires that category/suffix device selection be performed using the names in the system name set. However, it displays the device you selected using the active name set. We recommend that you switch to the system name set prior to cate- gory/suffix device selection and return to your preferred name set afterward. -
Page 75: Panel Lock
NV9646 User’s Guide Page Up This button scrolls a list of levels in X-Y mode or a list of MD devices in MD mode. There are 3 options for scrolling: 1 Scrolling the display only. The items on the selection buttons do not scroll. 2 Scrolling the selection buttons only. -
Page 76: Quick Source
Operation Buttons Quick Source A quick source button selects a source and performs an immediate take. Quick source and source buttons are similar, except that the quick source performs a take. Be aware of which buttons are quick sources so you do not perform an accidental take. Normally, the button text is the source’s mnemonic, but the configurer can assign any text to the button. - Page 77 NV9646 User’s Guide names and the current and preset sources for each device. If there is no preset device, that line of text is blank. A selection button is high-tally when its associated level or MD device is selected and low- tally otherwise.
- Page 78 Operation Buttons If your panel have a ‘VFD/Sel Paging Toggle’ button, 1 When the ‘VFD/Sel Paging Toggle’ button reads ‘Paging LCD Display’ , the panel’s display scrolls (and selection buttons do not). 2 When the ‘VFD/Sel Paging Toggle’ button reads ‘Paging Select Buttons’ , the selection buttons scroll by an increment equal to the number of buttons on the page (and the display does not scroll).
-
Page 79: Source
NV9646 User’s Guide Adding or Redefining MD Devices The configurer might have allowed you to redefine certain MD destinations. To do so is simple: (1) select an MD destination on a selection button, (2) choose a destination that is not on a selection button. You might have to navigate or scroll through a destination list to choose one. -
Page 80: Undefined
Operation Buttons Undefined An undefined button cannot be used and appears dark (unlit) on the panel. The term “undefined button” has meaning primarily to the configurer and not the operator. Toggle Display The button is a toggle that turns the panel’s display on or off. If the panel was configured in ‘All-Buttons’... -
Page 81: Xy/Md Mode
NV9646 User’s Guide Prior to a take, the preset source name is displayed on any selection buttons present on the panel. After a take, the selection buttons continue to display the source name, which is now the current source name. In MD mode, the X-Y Display button shows (1) current source, (2) preset source, and (3) destination for one of the selected MD devices —... - Page 82 Operation Lock, Protect, and Release 5 Select a quick source. The take is automatic. Single-Destination Panel (This scenario assumes that a destination was pre-selected during configuration.) 6 Select a source and press ‘Take’ . 7 Navigate to a quick source, and select it. The take is automatic. MD Mode 8 If required, enter MD mode.
-
Page 83: Broadcast Routes
NV9646 User’s Guide Note that when the panel is displaying aliases, and a device does not have an alias, the panel displays the system name. Broadcast Routes It is easy and normal to route a source to multiple destinations for audio and video routers. In contrast, machine control routes are typically point-to-point. -
Page 84: Manual Data Routing
Operation Chop Manual Data Routing If a control port for the source or destination is “in use, ” a take involving a machine control level occurs on all levels except the machine control level. You must break either the source’s control connection, the destination’s control connection, or both of those existing connections before you can take the source to the destination on the machine control level. -
Page 85: Salvo Mode
NV9646 User’s Guide 4 Select another source. This is the second source. The chop is immediately activated on the routers (of the default destination) that support chop. To terminate the chop, (1) press the chop button again to turn it off, (2) select the destination you had chosen for the chop, then (3) select any source. -
Page 86: Panel
Operation Panel User names are important in lock, protect, and release situations. The user who “owns” a lock or protect is identified by a user name. Press ‘Exit’ on the right to return to the menu. Panel Press the ‘Panel’ button to view panel data: Panel Panel Panel... - Page 87 NV9646 User’s Guide Setup Mode Setup mode occurs when the NV9646 is disconnected from its network and is freshly powered up. In setup mode, you can set or change the panel ID, determine software versions, and perform a test of the panel’s buttons. It is in setup mode that you must initially set the panel ID.
- Page 88 Operation LCD Control Press the ‘Push to Test’ button repeatedly to execute the test. Each time you press the button, the panel illuminates all its LCD buttons in a single color, changing the color each time you press the button. Keep pressing the button until all 7 colors (high and low tally) have been displayed.
-
Page 89: Gpio
GPIO Chapter 6 provides information about the tally (GPIO) interface. Summary The Interface ............... . . 81 GPIO Configuration Concepts . -
Page 90: Output
GPIO Output When the input transitions off or transitions on, the NV9646 notifies the router control system, which carries out the task defined for the input (if a task has been configured). During contact closure, a current of 1.2 mA flows. A maximum of 48 VDC can be applied to the tally input for less than 5 seconds without failure. -
Page 91: Configuring Outputs
NV9646 User’s Guide Click on a button under ‘Inputs’ to configure one of the 8 tally inputs. There are no actual GPIO buttons on the NV9646 control panel. Configuring Outputs Clicking an output button (one of 4) displays a “Relay Rule” dialog for the output: term term term... - Page 92 GPIO Configuring Outputs INPUT 3 OR INPUT 8 The relay will turn on when the entire expression is true. That is, when the switch occurs and either of the inputs (3 or 8) transitions from off to on. (To allow a relay to switch when an input transitions from on to off, precede the input term by “NOT.
-
Page 93: Configuring Inputs
NV9646 User’s Guide Relay output expressions can be as rich (or complex) as you require. Configuring Inputs Clicking an input button (one of 8) displays the GPI input dialog: An event is signalled when a transition occurs on the input from on to off or from off to on. You can configure the NV9646 to recognize either occurrence on any of the 8 inputs, and specify one of 4 behaviors for each event or both: 1 Execute a salvo. - Page 94 GPIO Configuring Inputs...
-
Page 95: Technical Details
Technical Details Chapter 7 provides electrical and mechanical specifications for the NV9646. Summary Power Specifications ..............87 NV9646 Specifications . -
Page 96: Nv9646 Specifications
Technical Details NV9646 Specifications 2.39 [60.7] 5.24 [133.0] Indicator LED 1.62 [41.0] AC Input DC Output Fig. 7-1: The power output has Molex 4-pin plug. See Power Cord Retention on page 94. NV9646 Specifications This table provides specifications for the NV9646. NV9646 Physical Specifications Specification Detail... -
Page 97: Environmental Specifications
NV9646 User’s Guide Environmental Specifications This table provides environmental specifications for the NV9646. NV9646 Environmental Specifications Specification Detail Operating temperature 0–40° C, ambient. Relative humidity 0 to 90%, non-condensing. Cooling No fan required. Defaults Initial Panel State Multi-destination mode or X-Y mode, selectable. Destination: the configured default. -
Page 98: Dhcp
Technical Details DHCP DHCP The panel is set up to respond to DHCP from the factory. It is possible to assign the panel a fixed IP address using the Panel IP Configuration Utility. Drawings The drawings on the following pages identify features and provide overall and critical dimensions. - Page 99 NV9646 User’s Guide Fig. 7-2: Front and Top Views of the NV9646...
- Page 100 Technical Details Drawings Fig. 7-3: Rear and Top Views of the NV9646...
-
Page 101: Misc. Topics
Misc. Topics Chapter 8 provides the following: Summary LCD Buttons ................93 Power Cord Retention . -
Page 102: Power Cord Retention
Misc. Topics Power Cord Retention Power Cord Retention Use the supplied retention strap to keep the AC power cord firmly connected to the power supply. Follow these steps to use the strap: 1 Firmly insert the AC power cord into the power supply. Examine the last figure in this section to see how the strap should be applied. -
Page 103: Ordering Information
NV9646 User’s Guide Ordering Information These are the NV9646 components: PS0001 12V power supply, 4-pin Molex connector, with cord, and cord retention strap. NV9646 NV9000 control panel. 46 button, 2RU, XY/MD, hierarchical. WC0053 Optional breakout cable for the tally interface... - Page 104 Misc. Topics Ordering Information...
-
Page 105: Glossary
Glossary (AES/EBU (Audio Engineering Society/European Broadcasting Union). AES and EBU are standards organizations. Breakaway A condition where a destination has multiple sources on different levels. Category A category represents a set of devices. (The concept of categories exists to make it easier to select devices at a control panel.) A category can contain sources, destinations, or devices that are both sources and destinations. - Page 106 Glossary Source/ The term “source device” is used interchangeably with “source” and the term “destination Destination device” is used interchangeably with “destination. ” A source is a device that is connected to one or more input ports. A destination is a device that is connected to one or more output ports.
-
Page 107: Index
Index Broadcast mode ......75 Broadcast routes ......75 Button Acquiring IP address (message) . - Page 108 Index toggle display ......72 Category lists ..... 26, 31, 59, 66 undefined .
- Page 109 NV9646 User’s Guide Documentation ......12 other ........2 Drawings .
- Page 110 Index GPIO ....4, 8, 12, 15, 81, 85, 89 tally ......8, 12, 15, 81, 89 Installation Global navigate (button) .
- Page 111 NV9646 User’s Guide Locating network (message) ....14 Monitor, preset ......22 Lock .
- Page 112 Index checkbox ....... . 24 Photos configuration ......17 NV9646, front .
- Page 113 NV9646 User’s Guide Revert to saved (button) ....18, 21 Special messages, symbol for ....2 RJ-45 connector .
- Page 114 Index Toggle display (button) ..... . 72 Tree window ....... . 38 Tree, button .
-
Page 115: Contact Us
Contact Us Grass Valley Technical Support For technical assistance, contact our international support center, at 1-800-547-8949 (US and Canada) or +1 530 478 4148. To obtain a local phone number for the support center nearest you, please consult the Contact Us section of Grass Valley’s website ( www.grassvalley.com An online form for e-mail contact is also available from the website.
Need help?
Do you have a question about the grass valley NV9646 and is the answer not in the manual?
Questions and answers