Related Manuals for BODY BIKE SUPREME
Summary of Contents for BODY BIKE SUPREME
- Page 1 INSTRUCTIONS BODY BIKE INDOOR CYCLE ® BODY BIKE INDOOR CYCLING APP BODY BIKE SUPREME ® ENGLISH...
- Page 2 TABLE OF CONTENTS EQUIPMENT REQUIRED Unpacking Sidewards play in posts Equipment required Introduction Drill bit A coin Specifications Drill 3mm Allen wrench General information 32mm wrench Warranty Bottom frame 13 mm wrench Adjustment handle Assembly 5mm Allen Wrench Unpacking Saddle Screwdriver Bottom frame 14 mm wrench...
- Page 3 INTRODUCTION This manual provides information on the assembly and maintenance of the BODY BIKE® indoor cycle. The manual is intended for the owners and service people responsible for cleaning and maintenance. Before assembling the cycle, please read the manual and prepare the correct tools, see equipment required page 2.
- Page 4 SPECIFICATIONS Manufacturer: Length, Width, Height: Materials BODY BIKE® International A/S Assembled size: Cast iron Niels Bohrs Vej 2 105cm, 60cm, 100cm Stainless steel DK-9900 Frederikshavn Packed size (5 cycles): Plastic (ABS) covers Denmark 120cm, 80cm, 114cm High quality bearings Phone: +45 9843 9696 Frame: Robot-welded, powder coated and hardened.
- Page 5 WARRANTY As information to our customers we hereby outline the warranty obligations applicable to BODY BIKE Indoor Cycles. ® The warranty comes into force the moment the unit leaves BODY BIKE International A/S. To get an overview see figure 1.
- Page 6 BODY BIKE® spare parts. All warranties are cancelled if the cycle has been modified or in any way not used as intended. Warranty repairs are to be carried out by BODY BIKE International A/S in Denmark. At the expense of BODY BIKE International A/S.
-
Page 7: Table Of Contents
ASSEMBLY Unpacking Bottom frame Handlebar Bottle holder Saddle Pedals... -
Page 8: Unpacking
UNPACKING BOTTOM FRAME 1) Open the top of the box. A fixing tool can be bought at BODY BIKE® International A/S to ease the mounting of the bottom frame. 2) Remove all the unmounted parts. 1) Arrange the bottom frames parallel on the floor next 3) Flatten the box on the floor next to the pallet. - Page 9 BOTTOM FRAME LIFTING SPOTS. Be sure that the saddle and handlebar are locked before lifting Tighten with no more than 12 Nm CAP NUT Figure 3 WASHER Back bottom Front bottom frame frame with wheels pointing forward Figure 4...
-
Page 10: Handlebar
HANDLEBAR BOTTLE HOLDER 1) Place the handlebar on top of the front post. Mount the bottle holder at the top of the handlebar, see figure 6. Insert the two rubber rings so the bottle holder is firmly fixed. 2) Screw an adjustment handle (size 32mm) clockwise into the socket from underneath the post, see figure 5. -
Page 11: Saddle
SADDLE PEDALS ONLY RELAVENT IF THE SADDLE IS NOT ALREADY 1) Place the right pedal arm with the socket INSTALLED. pointing upwards, see figure 8 . 1) Place the saddle in the track on the seat post. 2) Put maximum resistance on the brake, so the pedalarm is unable to rotate, see figure 9 2) Secure the saddle with the remaining adjustment handle, see figure 7. - Page 12 PEDALS Always screw on in the direction towards the handlebar Figure 10 Figure 8 Increase the resistance of the brake, before installing the pedals. Figure 9 Figure 11...
- Page 13 MAINTENANCE Cleaning Sidewards play in posts Cleaning the posts Adjustment handles Replacing the brake block Poly-V belt Removal of side covers...
-
Page 14: Cleaning
CLEANING After each workout, wipe the cycle down with tissue paper. If the cycle is covered in sweat or dirt, use water in a spray bottle and if necessary a tissue with Right side some washing-up liquid. cover has Remember handlebar and saddle. been removed PLEASE NOTE NEVER use alcohol or chemicals... -
Page 15: Sidewards Play In Posts
SIDEWARDS PLAY IN POSTS 3) Remount the seat post Front post 1) Remove the service hatch. See figure 17. 4) Carefully lift up the top cover as shown on figure Remove the right side cover by loosening the 8 14. Adjust the right hand side screw marked S2 with bolts by using a 3 mm Allen wrench. -
Page 16: Cleaning The Posts
CLEANING THE POSTS ADJUSTMENT HANDLES Every other week the posts need cleaning to Every 3 months the handles need cleaning and grease to protect them from sweat etc. protect the parts from sweat, dust, dirt and water. Pull out the seat post and the front post and wipe 1) Remove the adjustment handle and disassemble the them clean with an oily cloth, see figure 15. -
Page 17: Replacing The Brake Block
REPLACING THE BRAKE BLOCK 2) Clean all the parts thoroughly one by one using a The Kevlar® pad on the BODY BIKE® Synthetic steel brush. If the residue is extreme, a sharp object Brake has an expected durability of a minimum of 1500 hours, so eventually the brake pad will be worn. - Page 18 REPLACING THE BRAKE BLOCK 1) Remove both service hatches by loosening Remove the locks with a coin, see figure 17. screws 2) Release tension completely on the brake. 3) Remove the two screws holding the brake block to the frame by using an 8 mm wrench, see figure 18 Figure 18 4) Take the new brake block and fasten it to...
-
Page 19: Poly-V Belt
5) The belt should be tightened to approximately 125 kg/229 Hz. To measure this, a special device can be bought at your local BODY BIKE® distributor. Figure 21 6) Tighten the counter bolt (2) on both sides of the cycle again. -
Page 20: Removal Of Side Covers
REMOVAL OF SIDE COVERS The side covers can be removed e.g. if the belt needs to be changed. 1) Dismount the right pedal arm with an 8mm Allen wrench. See figure 22. Remove hatch. See figure 17. 2) Loosen all the screws holding the side cover with a 3 and 4 mm Allen wrench and remove them. - Page 21 TROUBLESHOOTER 1) How to get rid of downwards movement in 4) The poly-v belt doesn’t grip properly in the the saddle and steer? flywheel? If the front post or saddle post begins to slide down This can easily be fixed. Go to page 19 and follow the even though they are locked, it is time to tighten them instructions.
- Page 22 Need more information? Wanna know more about your BODY BIKE Supreme, follow the link below. https://body-bike.com/indoor-bikes/body-bike-supreme/ Need an upgrade? Take a look. Upgrade your BODY BIKE Supreme with the BODY BIKE Performance. Follow the link below. https://body-bike.com/explore/upgrade-your-body-bike/ Need support? If you have any questions, problems or anything else regarding your BODY BIKE, you are welcome to contact us on the mail below.
- Page 23 INDEX Information, general User weight Adjustment handles Wear and tear 3, 5, 6, 21 Adjustment screw 15, 19 Length Weight Assembly 7- 12 Maintenance 13-20 Width Belt Manufacturer Wheel Bottom frame Mounting Bottle holder Patent Brake Pedal 11-12 Cleaning Poly V-belt Cover 17,20 Post (front and seat)
- Page 24 Edition 5.0 BODY BIKE International A/S ® Niels Bohrs Vej 2 DK-9900 Frederikshavn Denmark Phone: +45 9843 9696 www.body-bike.com...
Need help?
Do you have a question about the SUPREME and is the answer not in the manual?
Questions and answers