Table of Contents
Advertisement
Rollixo RTS Solutions
This quick guide provides basic installation and commissioning guidance based on the Somfy
Rollixo RTS controller and safety edge solutions. Refer to the main Rollixo RTS controller and
SOMFY ROLLIXO QUICK COMMISSIONING
safety edge installation guides where more in-depth information relating to the installation
procedure of the Rollixo RTS system is required.
Rollixo RTS Safety Edge Solutions
There is one Somfy hardwired safety edge solution available with the Rollixo RTS:
Rollixo RTS Solutions
Rollixo RTS OSE - OSE stands for 'Optical Safety Edge'.
This is supplied with a safety edge via a hard wired spiral cable and is connected to a Somfy
This quick guide provides basic installation and commissioning guidance based on the Somfy
optical safety edge system. The optical safety edge consists of two optical cells mounted at
Rollixo RTS controller and safety edge solutions. Refer to the main Rollixo RTS controller and
each end of a rubber profile. The cells project an optical beam through a hollow section of
safety edge installation guides where more in-depth information relating to the installation
the profile, it becomes obscured once the rubber profile is depressed. This in turn results in a
procedure of the Rollixo RTS system is required.
signal from the safety edge, indicating that an obstacle has been detected.
Rollixo RTS Safety Edge Solutions
Additional steps must be taken to ensure the straight edge of the door meets with the straight edge
Aditional steps must be taken to ensure the straight edge of the door meets with the straight
There is one Somfy hardwired safety edge solution available with the Rollixo RTS:
of a floor extending into the guides, especially when removing posts - holes must be filled level with
edge of a floor extending into the guides. Failure to do so will result in; air + light gaps, false
the floor. Failure to do so will result in; air + light gaps, false activations of the safety edge etc.
activations of the edge etc.
Rollixo RTS OSE - OSE stands for 'Optical Safety Edge'.
This is supplied with a safety edge via a hard wired spiral cable and is connected to a Somfy
optical safety edge system. The optical safety edge consists of two optical cells mounted at
each end of a rubber profile. The cells project an optical beam through a hollow section of
the profile, it becomes obscured once the rubber profile is depressed. This in turn results in a
signal from the safety edge, indicating that an obstacle has been detected.
Aditional steps must be taken to ensure the straight edge of the door meets with the straight
edge of a floor extending into the guides. Failure to do so will result in; air + light gaps, false
activations of the edge etc.
Somfy motor wiring
1
Somfy motor wiring
Connect the motor wires into terminals 1, 2, 3
& 4 as illustrated above.
Note: The motor direction can be reversed during
1
the commissioning procedure.
Rollixo Quick GuideHW_A5_02.indd 4
Connect the motor wires into terminals 1, 2, 3
& 4 as illustrated above.
Note: The motor direction can be reversed during
the commissioning procedure.
Rollixo Quick GuideHW_A5_02.indd 4
16
M
L1
N
L2
2
3
4
M
L1
N
L2
2
3
4
L1
N
1
2
3
"Please refer to the Installer Guide
provided with every Rollixo, here
you will find the basic principles and
operating parameters for any CE
compliant safety edge system"
L1
N
1
2
3
"Please refer to the Installer Guide
provided with every Rollixo, here
you will find the basic principles and
operating parameters for any CE
compliant safety edge system"
Secure the motor supply
cable in place with the
cable clamp.
Page 4
Secure the motor supply
cable in place with the
cable clamp.
Page 4
M
L2
4
M
L2
4
12-07-17 14:02
12-07-17 14:02
Stop
Safety Ed
Sec
5
6
7
8
Advertisement
Table of Contents
