Parts List; Assem Bly Of The Base Plate; Assem Bly Of The Arm S; Assem Bly Of The Seesaw - SpaceraiL Spacewarp Level 2.1 Instruction Manual

Parts List

Tools for installation
Use 1 x C/ LR 14 battery (not included).
P arts list
[B 1 ] [S 1 ] 300m m
[B1] Base plate [S1] Shaft 300m m
2 x
[A 4 ]
[A4] Arm holder B [A5] Arm w rench
20 x
[F 1 ]
[B2] Base holder (big)
[F1] Seesaw
3 x
1
A sse m b ly o f b ase p la te
1. Assem ble the base plate (6 pieces).
Pay attention to a proper seatingof the
clips and slots (fg. 01)
2. Fasten the base holders (B2 + B3) in the
correct positions (fg. 01)
2
A sse m b ly o f arm s
1. Assem ble the arm s according to fg. 02.
Caution: Arm holder A (A2) + arm holder B
(A4) are different. 17 arm s are needed for the
com plete set-up of „Star Coaster Lev el 2"
2. Insert the arm w rench into the arm holder
A and turn it by 90 degrees to f x the arm
(fg. 03)
N ote:T o m odify the ang le of the arm , release the
f x ation frst
3
A sse m b ly o f se e sa w
1. Insert the seesaw into the rail stand
(fg. 04)
2. Insert the seesaw into arm holder B, then
attach the com plete com ponent to the
shaft (fg. 05). Refer to the assem bly of
arm s (fg. 02+ 03). Note: T o m odify the
angle of the arm , release the f x ation frst
4
Pliers
Handle the com ponents w ith care to prev ent them from getting lost.
[S2 ] 200m m
[S2] Shaft 200m m
7 x 2 x
[A 6]
[A 5 ]
[A 6] Rail stand
37 x 40 x
[B2 ] [B3 ]
[B3] Base holder (sm all)
1 x 1 x
[B2] Base holder (big)
-
1
-
01
[B1] Base plate
03
[F1] Seesaw
Mount left hand side
[A4] Arm holder B
05
Hole profle
Note: W hen turning the arm w rench,
m ake sure not to change the right
position of the arm
Tape Measure
[R 1 ] 10.000m m
[R1] Rail 10,000mm [A 1] Arm
1 x
[G 1 ]
[G 1] G earbox [E1] Elev ator helix
1 x
[S3 ]
[S3] Connecting piece [G 2] G earbox socket
1 x
2
02
[B3] Base holder (sm all)
[A4] Arm halter B
[A4] Arm holder B
T op-dow n v iew
3
04
Install 2 pcs
[A 3] A rm tube
Hole profle
Hole profle
Mount right hand side
Install 1 pc
[A 1 ]
[A 2 ]
[A2] Arm holder A
1 7 x 1 7 x
[E 1 ] [E2 ]
[E2] Elev ator ring
12 x 3 x
[G 2 ]
Steel balls
1 x 2 x
[A3] Arm tube
[A5] Arm w rench
Approx . 55m m
[A 6] Rail stand
Hole profle
Note: W hen turning the arm w rench, m ake sure not to
change the right position of the arm
[A 3 ]
[A3] Arm tube
20 x
[E3 ]
[E3] Elev ator cov er
1 x
[R2 ]
[R2] Rail joining
4 x
[A 1] Arm
[A2] Arm halter A
[A2] Arm holder A
T op-dow n v iew