KaVo K-POWERgrip Instructions For Use Manual
Hide thumbs Also See for K-POWERgrip:

Advertisement

Instructions for use
K-POWERgrip Handstück 4941
Always be on the safe side.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the K-POWERgrip and is the answer not in the manual?

Questions and answers

Summary of Contents for KaVo K-POWERgrip

  • Page 1 Instructions for use K-POWERgrip Handstück 4941 Always be on the safe side.
  • Page 2 Sales: Manufacturer: KaVo Dental GmbH Kaltenbach & Voigt GmbH Bismarckring 39 Bismarckring 39 D-88400 Biberach D-88400 Biberach Tel. +49 7351 56-0 Fax +49 7351 56-1488...
  • Page 3: Table Of Contents

    Instructions for use K-POWERgrip Handstück 4941 Contents Contents Contents User instructions Service User guide 1.2.1 Abbreviations 1.2.2 Symbols 1.2.3 Target group Warranty terms and conditions Transportation and storage 1.4.1 Currently valid packaging ordinance 1.4.2 Damage in transit 1.4.3 Information on the packaging: Storage and transportation...
  • Page 4: User Instructions

    Service hotline: +49 7351 56-1600 Service.Zahntechnik@kavo.com Please indicate the product serial number in all requests. Additional information can be obtained at: www.kavo.comAdditional information can be obtained at: www.kavo.com 1.2 User guide Requirement Read these instructions prior to first use to prevent misuse and damage.
  • Page 5: Warranty Terms And Conditions

    12 months from the date of purchase demonstrated by the purchaser. In case of justified complaints, KaVo will honor its warranty with a free replacement or repair.
  • Page 6: Information On The Packaging: Storage And Transportation

    ADSp, Art. 26). Outside of Germany Note KaVo is not liable for damage arising from transportation. Immediately inspect the delivery after receipt! If the packaging is visibly damaged on delivery, please proceed as follows: 1. The recipient of the package must record the loss or damage on the delivery receipt.
  • Page 7 Instructions for use K-POWERgrip Handstück 4941 1 User instructions | 1.4 Transportation and storage Transport upright with the arrows pointing upwards Protect from impact. Protect from moisture. Permissible stacking load Temperature range Humidity Air pressure 5/26...
  • Page 8: Safety

    Instructions for use K-POWERgrip Handstück 4941 2 Safety | 2.1 Description of safety instructions 2 Safety 2.1 Description of safety instructions 2.1.1 Warning symbol Warning symbol 2.1.2 Structure DANGER The introduction describes the type and source of the danger. This section describes the possible consequences of misuse.
  • Page 9: Product-Specific

    This product has only been approved for use indoors. The overarching guidelines and/or national laws, national regulations and the rules of technology applicable to the startup and use of the KaVo product for the intended purpose are to be applied and complied with.
  • Page 10: Safety Instructions

    Authorized to repair and service the KaVo product: ▪ Technicians from KaVo branches with appropriate product training. ▪ the technicians of the KaVo franchised dealers specifically trained by KaVo. KaVo cannot accept responsibility for damage caused by: ▪ External factors beyond its control, poor media quality or defective installation ▪...
  • Page 11 Any waste generated must be recycled or disposed of in a manner safe for humans and the environment, and the applicable national regulations complied with. Questions on proper disposal of the KaVo product can be answered by the KaVo branch.
  • Page 12: Product-Specific

    Instructions for use K-POWERgrip Handstück 4941 2 Safety | 2.3 Safety instructions 2.3.2 Product-specific CAUTION Risk due to incorrectly stored handpiece. Injury caused by chucked drill or grinder. Damage to clamping system caused by handpiece falling down. ▶ Store the handpiece properly in a tray or tool carrier.
  • Page 13: Product Description

    Instructions for use K-POWERgrip Handstück 4941 3 Product description | 3.1 K-POWERgrip 4941 handpiece 3 Product description 3.1 K-POWERgrip 4941 handpiece K-POWERgrip 4941 handpiece A Chuck key Cover B Clamp Straight pin C Cleaning brush Grip tip Handpiece part Motor part...
  • Page 14: Technical Data

    Instructions for use K-POWERgrip Handstück 4941 3 Product description | 3.3 Technical data 3.3 Technical data Speed Area 1,000 to 50,000 rpm Dimensions Length 165 mm Diameter of handpiece 29 mm Diamter of motor part 28 mm Weight Handpiece approx. 250 g Cable ca.
  • Page 15 Instructions for use K-POWERgrip Handstück 4941 3 Product description | 3.3 Technical data Relative humidity: 5 % to 95 % (non-condensing ) Air pressure: 700 hPa to 1060 hPa Note Prior to start-up, very cold products must be heated to a temperature of heat to 20 °C to 25 °C.
  • Page 16: First Use

    Opening the chuck will lock the handpiece; in the event of unintentional operation, the control will switch to error mode. The combination of the control unit and handpiece must be approved by KaVo. Note When it is new, you can hear a soft, irregular clicking or buzzing at high speeds of the micromotor.
  • Page 17: Operation

    Note Once you have inserted the tool (insert the tool as far as it will go, tool shaft length: minimum 16 mm) you need to check the functionality of the chuck. KaVo recom‐ mends a grip test at 50 N.
  • Page 18: Service And Care

    Instructions for use K-POWERgrip Handstück 4941 6 Service and Care | 6.1 Cleaning 6 Service and Care KaVo recommends that only original KaVo parts be used for operating and repairs ® since their safety, operation and specific suitability have been tested in extensive tests.
  • Page 19 Instructions for use K-POWERgrip Handstück 4941 6 Service and Care | 6.1 Cleaning ▶ Remove the chuck ▶ Insert a new tool or test probe into the chuck as far as it will go. ▶ Grip the handpiece part 2, and turn the motor 3 in the direction indicated by the arrow until the chuck closes completely.
  • Page 20: Servicing

    Instructions for use K-POWERgrip Handstück 4941 6 Service and Care | 6.2 Servicing ▶ Reattach the cover ▶ If worn, replace the cover (three units in the care set). ▶ Remove the clamp B from the grip tip. ▶ Insert a new tool or test probe into the chuck as far as it will go.
  • Page 23: Replacing The Cable

    B. ▶ Insert the cover Note To increase the service life of the ball bearings, KaVo recommends the following: After changing the ball bearing, let the handpiece idle for about 60 minute at 10,00 to 15,000 rpm.
  • Page 24: Troubleshooting

    Instructions for use K-POWERgrip Handstück 4941 7 Troubleshooting 7 Troubleshooting WARNING Repair and servicing the electrical part of the unit. Electrical shock. ▶ Only a qualified professional or trained individual may repair or service the electrical part of the device.
  • Page 25: Accessories

    Instructions for use K-POWERgrip Handstück 4941 8 Accessories 8 Accessories Presentation Material summary Mat. no. Handpiece rest 0.642.0352 Chuck 30 mm 0.674.4881 Chuck 2.35 mm 0.674.4871 Key D 0.411.3962 Socket wrench E 0.411.2310 23/26...
  • Page 26: Ersatzteile

    Instructions for use K-POWERgrip Handstück 4941 9 Ersatzteile 9 Ersatzteile Verk.-Nr . K POWERgrip Typ 4941 08/2004 Mat.-Nr . 1.002.2916 01.40 0.410.0732 0411.3180 0.674.7942 0.222.4018 0.200.0836 0.200.0837 0.200.6095 0.220.0779 0.201.8083 1.002.3648 0.674.4861 0.220.0778 0.200.6093 0.200.6219 1.002.3367 P ower g r i p P ower g r i p 0.200.6320...
  • Page 27 Instructions for use K-POWERgrip Handstück 4941 9 Ersatzteile Verk.-Nr. K POWERgrip Typ 4941 03/2009 Mat.-Nr. 1.002.2916 01.40 0.410.0732 ø 2,35 mm 0.674.8212 ø 3,00 mm 0.674.8482 ø 2,35 mm 0.674.4871 ø 3,00 mm 0.674.4881 0.674.9012 0.200.0826 0.200.6220 0.674.9002 1.000.1260 1.000.3586 0.222.4044...
  • Page 28: Statement Of Conformance

    Instructions for use K-POWERgrip Handstück 4941 10 Statement of conformance 10 Statement of conformance 26/26...
  • Page 32 1.007.1541 · Fk · 20090713-01 · en...

This manual is also suitable for:

4941

Table of Contents