Scosche MagicMount UQ01 Manual

Scosche MagicMount UQ01 Manual

Universal flush mount bezel

Advertisement

Register your product onllne at
INSTALLER DISCRETION After reviewing the recommended placement guidelines stated
on page 4, please use installer discretion when proceeding to install the UQ01. Location
modification may be required for this installation, proceed with caution. If you are unsure
or feel that the installation is to difficult, seek professional installation. Note that additional
installation fees may apply and vary by their location. Scosche is not responsible or liable for
any additional fees or modification done by the installer.
READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS MOUNT KIT.
WARNING: Do not use the magnetic mount with any hard-drive based devices such as:
iPod classic, iPod Video and Zune MP3 players. Use caution whenever removing or handling
plastic parts of any vehicle. Unnecessary force or pressure can cause pieces to crack or
break. Please use a plastic card to remove the metal plates. Remove adhesive residue with a
non-abrasive cleaner.
AIRBAG WARNING: Do not place this pad or any other object on or near the airbag. In the
event of deployment, objects placed on or near airbag could cause serious injury.
CAUTION: This magnetic device is not a toy. The small magnets are harmful if swallowed.
Keep away from children.
Wirelessly charge your Qi-enabled smartphone without the need to plug your device into a car
charger or USB cable. Quickly charge your device at 5W or 10W charging. The high powered
neodymium magnets are 100% safe and will not damage your device. The UQ01 works with
Qi-enabled smartphones from these manufacturers: Apple, Samsung, Google, Microsoft, LG,
HTC, Motorola. Also works with Qi-enabled cases, receivers, and battery covers.
CAUTION: Disconnect your vehicles negative battery terminal before the installation to help prevent electrical
damage. We recommend the use of a volt/ ohm meter over a test light to check wiring. A test or grounded
wire probe can cause damage to the vehicle's computer and/or diagnostic system. Avoid all factory airbag
wiring - airbags can accidentally deploy causing serious injury or death.
NOTE: See your vehicle's instructions for any special tools your installation might require.
IMPORTANT! DO NOT RETURN PRODUCT TO THE RETAILER. If you need assistance or
replacement parts contact us at: 1-800-363-4490 X1
Our office hours are: Mon-Fri: 8AM-5:30PM (PST) and Sat: 8am-2PM (PST)
This instruction booklet is based on carefully documented data and research of automobile disassembly,
wire harness/codes and information pertaining to the installation of this kit. Scosche Industries, Inc. cannot
be held responsible for discrepancies/ inconsistencies that may occur due to the automobile manufactur­
ing changes or options, or damages that may occur in the automobile during the installation of compo­
nents while using this booklet.
© 2018 SCOSCHE INDUSTRIES, INC.
www.scosche.com/register
UNIVERSAL FLUSH MOUNT BEZEL
MODIFICATION REQUIRED
PRELIMINARY INTRODUCTION
LIABILITY DISCLAIMER
I
www.scosche.com/contact.
UQ01
UQ01 06/19

Advertisement

Table of Contents
loading

Summary of Contents for Scosche MagicMount UQ01

  • Page 1 If you are unsure or feel that the installation is to difficult, seek professional installation. Note that additional installation fees may apply and vary by their location. Scosche is not responsible or liable for any additional fees or modification done by the installer.
  • Page 2: Parts Included

    Do not use any heat or liquids to remove the plate, due to risk Template Guide to the to damaging your phone. Contact Scosche Customer Service for any additional assistance at 800.363.4490 Ext. 1 or customerservice@ the bottom of your phone.
  • Page 3: Removing The Plate

    Slowly lift up and remove the plate. Do not use any heat or liquids to remove the plate, due to risk of damaging your phone. Contact Scosche Customer Service for any additional assistance at: 1800.363.4490 Ext. 1 or customerservice@scosche.com...
  • Page 4: Foreign Object Detection

    OFF, you may need turn the ignition to the ON position in order to operate the MQUSM. For questions about this product please contact our Scosche tech support team at: (800) 363-4490 ext.1 www.scosche.com/contact.
  • Page 5: Test Connection

    1. Tap into the vehicle's 12V power and ground wires using appropriate tools. 2. Next, color match the clamps to the vehicle's power and ground wire then connect them. Note: Scosche recommends striping the clamping area on the vehicle's power and ground wires for best connection.
  • Page 6: Installation Instructions

    ASSEMBLY Modification Required Proceed with CAUTION! Use the Illustration for demonstration use only. Vehicle disassembly/ modification may vary per installation/vehicle. INSTALLATION INSTRUCTIONS 1. Select a mounting location (A). 2. Route the provided power harness to the nearest 12V power (B). 3.
  • Page 7 UQ01 TEMPLATE Use the template provided below as guide to help with your modification. Note: Use a contrasting marker/chalk to outline the desired area to be modified. - - -- --- ..5 .2 0 6 in tact custo e.com ( 80 .._ .______ _...
  • Page 8: Fcc Statement

    This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter. For complete warranty details or questions visit us online at www.scosche.com or contact us at: www.scosche.com/contact customerservice@scosche.com 1 (BOO) 363-4490 ext.1...

Table of Contents