Sony MVC-CD200 Service Manual page 2

NP-FM50 battery pack
Storage temperature
–20°C to +60°C (–4°F to
Battery type
+140°F)
Lithium ion
Maximum output
Dimensions (Approx.)
voltage
MVC-CD200: 143×92×
DC 8.4 V
89 mm (5 3/4×3 5/8×
3 5/8 inches) (w/h/d)
Mean output voltage
MVC-CD300: 143×92× DC 7.2 V
94 mm (5 3/4×3 5/8×
Capacity
3 3/4 inches) (w/h/d)
8.5 Wh (1180 mAh)
Mass (Approx.)
Operating temperature
MVC-CD200: 610 g
0°C to 40°C (32°F to 104°F)
(1 lb 6 oz)
Dimensions (Approx.)
38.2×20.5×55.6 mm
MVC-CD300: 650 g
(1 9/16×13/16×2 1/4 inches)
(1 lb 7 oz) (including NP-
FM50 battery pack, disc and (w/h/d)
lens cap, etc.)
Mass (Approx.)
76 g (3 oz)
Built-in microphone
Electret condenser
Accessories
microphone
AC-L10A/L10B/L10C
Built-in speaker
AC power adaptor (1)
Dynamic speaker
Power cord (mains lead) (1)
Ferrite Core (1)
AC-L10A/L10B/L10C
USB cable (1)
AC power adaptor
NP-FM50 battery pack (1)
Power requirements
A/V connecting cable (1)
100 to 240 V AC, 50/60 Hz
8 cm CD adaptor (1)
Rated output voltage
Mavica disc (2) (CD-R (1),
DC 8.4 V, 1.5 A in operating
CD-RW (1))
mode
Shoulder strap (1)
Operating temperature
Lens cap (1)
0°C to 40°C (32°F to 104°F)
Lens cap strap (1)
Storage temperature
CD-ROM (2)
–20°C to +60°C (–4°F to
O perating instructions (2)
+140°F)
2-pin conversion adaptor (1)
Dimensions (Approx.)
(E, Hong Kong, Tourist model
125×39×62 mm (5×1 9/16×
only)
2 1/2 inches) (w/h/d)
Mass (Approx.) Design and specifications
280 g (10 oz)
are subject to change
without notice.
CAUTION
Use of controls or adjustments or performance
procedures other than those specified herein may
result in hazardous radiation exposure.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are
"pinched" or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly
transistors, that were installed during a previous repair. Point
them out to the customer and recommend their replacement.
Table for difference of functions
Model
Lens
CCD imager
Image size
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
4. Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and
recommend their replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
— 2 —
MVC-CD200
Carl Zeiss lens
Optical zoom
Digital zoom
Filter diameter 37mm
Size 1/2.7 type
Pixels 2.1mega
Still 1600×1200
1600 (3:2)
1024×768
640×480
Movie
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
MVC-CD300
a
3×
6×
52mm
1/1.8 type
3.3mega
2048×1536
2048 (3:2)
1600×1200
1280×960
640×480
320 (HQ)
320×240
640×480