Related Manuals for unicraft SRWH 3001 SIL
Summary of Contents for unicraft SRWH 3001 SIL
- Page 1 Operating Instructions Special Floor Jack SRWH 3001 SIL SRWH 3002 EF SRWH 3002 EF SRWH 3001 SIL...
-
Page 2: Table Of Contents
Product identification 1.1 Copyright ............3 Special Floor Jack Item number 1.2 Customer service..........3 1.3 Limitation of liability ..........3 SRWH 3001 SIL 6201121 2 Safety................3 SRWH 3002 EF 6201122 2.1 Symbol explanation ..........3 2.2 Obligations of the operating company ....4 2.3 Requirements to staff.......... -
Page 3: Introduction
Introduction Introduction 1.3 Limitation of liability All information and notes in these operating instructions You have made a good choice by purchasing the UNI- were summarised while taking applicable standards CRAFT floor jack. and rules, the state-of-the-art technology and our long- term knowledge and experiences into consideration. -
Page 4: Obligations Of The Operating Company
Safety - The operating company must be informed about the applying industrial safety regulations and fur- CAUTION! ther analyse hazards resulting from the special This combination of symbol and signal words indi- working conditions at the place of use of the floor cates a possibly dangerous situation which may jack. -
Page 5: General Safety Regulations
Safety Operator 2.5 Safety information for operating personnel The operator is instructed by the operating company - The operating staff must always make sure that the about the assigned tasks and possible risks in case of specified max. Load capacity of the floor jack is not improper behaviour. -
Page 6: Personal Protective Equipment
Intended Use 2.7 Personal protective equipment 3.1 Foreseeable misuse With the floor jack no reasonably foreseeable misappli- The personal protective equipment serves to protect cations are possible which could lead to dangerous si- per-sons against impairments of safety and health while tuations with personal injury if the intended use is obser- wor-king. -
Page 7: Environmental Conditions
Transport, packaging, storage Transport, packaging, storage Size [mm] 3001 SIL 3002 EF 5.1 Transport Check the floor jack on delivery for any visible trans-por- tation damage. If you notice any damage to the device please report this immediately to the carrier or dealer. NOTE! 1756 1840... -
Page 8: Description Of The Device
4 Lifting arm lever extension and screw the two pump lever 5 Swivel castor parts together with the screw (SRWH 3001 SIL 6 Jack saddle model only). Illustrations in this manual may differ from the original. -
Page 9: Before The Start-Up
Before the start-up Before the start-up Operation Step 1: Bleed the hydraulic system: DANGER! Pull up the pump lever and turn it clockwise to open the drain valve. Danger to life due to falling of the load! Falling loads can cause serious injury or death. When the lifting arm is fully lowered, pump seve- - Never exceed the specified maximum load stride. -
Page 10: Operating Conditions
Operation 9.1 Operating conditions 9.4 Lower the load SRWH-Series ATTENTION! Temperature range -5°C to +40°C Check that there are no persons, tools or devices Storage temperature -25°C to +55°C under the trolley. range Humidity (at 40°C) up to 85% max. Step 1: Turn the pump lever about its own axis to the right (clockwise) to close the drain valve. -
Page 11: Care, Maintenance And Repair
Care, maintenance and repair 10 Care, maintenance and repair 10.1 Care by cleaning The floor jack must always be kept in a clean condition. Use protective gloves! Fig. 8: Lubrication points on the floor jack Step 2: Check the floor jack for external damage before NOTE! each use. -
Page 12: Troubleshooting
Troubleshooting Step 3: When the used oil is completely drained, fill with new hydraulic oil. Use only new, clean hydraulic oil, viscosity class "ISO VG 15", volume 260 ml. ATTENTION! Only use hydraulic oil of the same type. Never mix different types of oil. Fig. -
Page 13: Disposal, Recycling Of Used Devices
- Always contact the manufacturer in case of uncer- The item number of your device: tainties. Special Floor Jack SRWH 3001 SIL: 6201121 Special Floor Jackr SRWH 3002 EF: 6201122 Tips and recommendations The manufacturer's warranty will become null and... -
Page 14: Spare Parts Drawings
Spare parts 13.2 Spare parts drawings Spare parts drawing 1: SRWH 3001 SIL Fig. 10: Spare parts drawing 1 - SRWH 3001 SIL SRWH-Series | Version 1.01... - Page 15 Spare parts Spare parts drawing 2: SRWH 3001 SIL pump Fig. 11: Spare parts drawing 2: SRWH 3001 SIL pump SRWH-Series | Version 1.01...
- Page 16 Spare parts Spare parts drawing 1: SRWH 3002 EF Fig. 12: Spare parts drawing 1 - SRWH 3002 EF SRWH-Series | Version 1.01...
- Page 17 Spare parts Spare parts drawing 2: SRWH 3002 EF pump Fig. 13: Spare parts drawing 2: SRWH 3002 EF pump SRWH-Series | Version 1.01...
-
Page 18: Hydraulic Plan
Hydraulic plan 14 Hydraulic plan SRWH 3001 SIL SRWH 3002 EF Fig. 14: Hydraulic plan SRWH 3001 SIL (top), SRWH 3002 EF (bottom) SRWH-Series | Version 1.01... -
Page 19: Ec Declaration Of Conformity
D-96103 Hallstadt herewith declares that the following product Unicraft® Werkstatttechnik Product group: Special Floor Jack Machine type: Designation of machine*: Item number: SRWH 3001 SIL 6201121 SRWH 3002 EF 6201122 ______________________ Serial number*: 20_____ Year of manufacture*: *Fill in these fields according to the information on the type plate complies with all the relevant provisions of the abovementioned Directive, including its amendments in force at the time of the declaration. - Page 20 www.unicraft.de...