MRC 0001902 Quick Start Manual

PROGRAMMING
This decoder supports all program modes and read back features. With MRC
Prodigy Advance² DCC you can read its address and CV values.
CV Description
CV1 Short address
CV2 Start voltage
CV3 Acceleration
CV4 Deceleration
CV5 Top voltage
CV29 Basic configuration
CV7 Manufacturer version number
CV8 Manufacturer ID
CV17 Long address upper byte
CV18 Long address low er byte
CV19 Advanced consist address
CV21=0, all accessory function w ill follow its ow n address.
CV21
CV21=1, all functions w ill follow the consist address
Master volume control
CV49
CV50 Horn type
CV51 Horn volume
CV52 Bell type
Bell volume
CV53
Bell ring rate
CV54
Diesel rumble volume
CV55
CV56 Brake squeal volume
CV57 Dynamic brake volume
CV58 Air release volume
Air pump volume
CV59
Safety pop valve volume
CV60
Engine cooling fan volume
CV61
Coupling volume
CV62
CV63 Auto ditch lights flash w ith horn enable
CV64 Rail w heel clack volume
kick start voltage
CV65
28 speed steps table w hile CV29.4=1
CV67-94
User identification number
CV105
User identification number
CV106
CV112 Sand dropping volume
CV113 Back EMF Load control proportional gain Kp
Back EMF Load control integral gain Ki
CV114
Auto brake squeal enable/disable
CV115
Flange squeal volume
CV116
CV117 Light brightness
CV118 ACC1 light mode
CV119 ACC2 light mode
out sync time
CV120
Mars light flashing on/off (F28)
CV121
Diesel notch mode, 0=auto-notch, 3=manual notch
CV122
CV123 prime mover type, 4 types, 4=sound off
CV124 Back EMF Load control intensity (0=off)
CV125 Set it to1 to restore some factory default CV settnings
SPEED TABLE CV67-CV94 FOR 28 SPEED STEPS
When CV29's bit 4 is set to "1" it will use the speed table formed by CV67-CV94 to
control speed (motor voltage). It allows you to setup each speed for all 28 speed
steps. First, program CV29 to 18 for short addresses (1-127) or program CV29 to 50
Range Default
for long addresses (128-9999) to enable speed table control. Then select throttle to
1-127 3
28 speed steps and run your loco at speed step 1. Use program CV on the main to
0-32 0
change CV67's value (1-255) to adjust step 1's speed. The kick voltage, CV65 is only
0-32 0
applied when the speed step changes from 0 to 1. You should switch between 0 to
1 many times to check step 1's speed. When done with CV67, select speed step 2
0-32 0
and program CV68. CV68's value must be greater then CV67's. When done with
0-32 32
CV67-CV94, use read back CV to make sure their values are in increasing order.
--- 2
Note: When using MRC Prodigy DCC to program addresses it will automatically disable
--- 32
the speed table (set CV29's bit 4 to "0"). Programming CV125 to 1 will also disable the
speed table and re-program CV67-CV94 to a default linear speed setting.
--- 143
192-231 192
BACK EMF LOAD CONTROL (PID CONTROLLER)
0-255 3
0-127 0 This decoder is equipped with adjustable back EMF closed loop speed control. Its
proportional gain (CV113), integral gain (CV114) and derivative gain (fixed) are pre-
0-1 0
tuned for most locomotives. We recommendend that you do not change these set-
tings. Too much gain may cause the motor to oscilate (become unstable). Too little
1-16 16
gain may cause slow reponse. Please get some basic knowledge of PID feedback
0-22 13
control before trying to adjust CV113/114.
0-15 12
0-6 3 TROUBLE SHOOTING
0-15 12
Whenever the decoder doesn't work please use the program track to program CV#
0-50 3 125 with value 1 to restore the decoder to factory settings. This should bring the
decoder to life with address #3.
0-15 12
0-15 7
FCC COMPLIANCE
0-15 12
This device complies with part 15 of the FCC Rules. Operation is subject to the
0-15 12
following two conditions. (1) This device may not cause harmful interference, and
0-15 12 (2) This device must accept any interference received, including interference that
may cause undesired operation.
0-15 12
0-15 12
RETURN PROCEDURE
0-15 12
This decoder carries a 6 month warranty against factory defects. This warranty
0-1 1(enable)
does not include abuse, misuse, neglect, improper installation, or any modifications
0-15 12
made to this decoder, including but not limited to the removal of the NMRA plug if
0-63 63
applicable. If it should become necessary to return the decoder for warranty repair/
1-255 linear
replacement, please include a copy of the original sales receipt. Please include
0-255 0 a letter (printed clearly) with your name, address, daytime phone number, and a
detailed description of the problem you are experiencing. Please also include a check
0-255 0
or a money order for $10.00 to cover return shipping and handling. If the decoder is
0-15 12
no longer considered under warranty, then please include a check or a money order
0-31 20
for $55.00 to cover the cost of repair or replacement and return shipping and handling.
0-31 10
Be certain to return the decoder only.
0-1 1(enable)
Any questions regarding Warranty Policy can be directed to our Customer
Service Department by calling 732-225-6360 between the hours of 8:30am
0-15 12
and 6:00pm EST, or by emailing: rrtech@modelrectifier.com
0-255 200
0-6 0
Send the decoder to:
0-6 0
0-255 150
0-1 1
0-3 3
0-4 0
0-255 160
0-1 0
Model Rectifier Corporation
Attn: Parts & Service
80 Newfield Avenue
Edison, NJ 08837-3817 U.S.A
Printed in USA
HO 16 Bit Stereo Sound Decoder for
E8/9 or PA Locomotives (DC/DCC)
Item #0001902 for Proto 2000 Locos
Thank you for purchasing our most advanced triple core stereo
sound decoder available. Combined with any DCC System or the
MRC Tech 6, our true live capture digital diesel
bring your Proto 2000 locos to life.
•
Adjustable back EMF load control with utlra slow speed
control
•
16 bit sound control with 16 levels of sound volume
•
Dual out of synch EMD 567B prime movers for realistic
operation
•
1.5 amp capacity
•
2 different prime mover sounds- EMD 567B/Alco 539T
•
Programmable for either 2-digit (1-127) or 4-digit (1-
9999) addresses
•
Programmable start voltage and top voltage
•
Programmable acceleration and deceleration rates
•
Programmable 14, 28/ 128 speed steps
•
Programmable user selectable 22 types of horns
and 6 types of bells
• Supports full read back
•
28 accessory functions (F1-F28)
•
Supports advanced consisting (CV19)
•
Supports programming on the main (OPS mode)
•
Compatible with NMRA DCC standards
•
Complies with part 15 of FCC regulations
•
Programmable individual sound volumes
•
True stereo sound comes with two 28mm speakers
sound decoder will