Table of Contents
Related Manuals for HAAS + SOHN HSP 6 PALLAZZA-III 519.08
Summary of Contents for HAAS + SOHN HSP 6 PALLAZZA-III 519.08
- Page 1 PELLET STOVE Nameplate: Aufstellungs- und Bedienungsanleitung Pelletofen Fiche descritive Poele Schema tecnica strufa Camino Equipment sheet Fireplace Tshnicki podaci Kaminsku Podatkovni list Kaminsko 0541908001401a 1 / 18...
-
Page 2: Table Of Contents
Table of Contents General information General safety information Electrical connection Chimney 4.1. Weather conditions 4.2. Chimney flue draft at rated heat output of the stove 4.3. Connection to the chimney 4.3.1. Multiple use Installation 5.1. Minimum gaps to flammable components: 5.2. -
Page 3: General Information
Please read through these operating instructions carefully. You will be informed about the function and handling of this stove and you will also save fuel and conserve the environment by heating correctly. The attached equipment sheet is part of these operating instructions. General information ... -
Page 4: Weather Conditions
4.1. Weather conditions For the safe operation of the fireplace, it must be ensured that the chimney is able to build up the necessary flue draft. Particular attention needs to be paid to this during the transition period (e.g. autumn and spring) or during poor weather conditions (e.g. -
Page 5: Combustion Air Supply
5.2. Combustion air supply It must be ensured that there is sufficient fresh air at the place of installation. 5.3. Outside air connection We recommend using the outside air connection for the supply of combustion air in order not to use up the valuable indoor air when heating. -
Page 6: Operator Console Functions
Operator console functions 6.1. Buttons “On/Off” button „On/Off“ “Plus” button “Minus” button “OK” button 6.1.1.1. Symbols on the display ￭ 10:34 ￭ Symbol : Stove is WLAN capable ∓ target room temperature room temperature Operating mode menu Function of the buttons Operating the pellet stove 7.1. -
Page 7: Using For The First Time
7.3. Using for the first time 7.3.1. General: Before using for the first time Remove any stickers. Remove all accessories from the pellet tank and the combustion chamber. Check whether the combustion chamber cladding (see appliance sheet - combustion chamber replacement part Figure 8a) is attached to its fastenings. -
Page 8: Setting Target Room Temperature (Required Room Temperature)
7.3.2.4. Setting TARGET room temperature (required room temperature) ￭ 10:34 ∓ 28°C 23°C Procedure: The “TARGET room temperature” is set with the “Plus” or “Minus” buttons. The set value is saved by pressing the “OK” button. The “TARGET room temperature” can be changed at any time as often as you want during operation with the “Plus” or “Minus”... -
Page 9: Energy Saving Mode - Actual Room Temperature Display
8.2. Energy saving mode - ACTUAL room temperature display 23°C The display energy saving mode is automatically activated after a few minutes. The display shows ACTUAL room temperature. Note: Pressing any button makes the welcome page appear again on the display after approx. 3 seconds. 8.3. -
Page 10: Operating Mode Week Program - Settings
Procedure: The functions can be selected with the “Plus” or “Minus” buttons. The function is chosen by pressing the “OK” button. 9.1.1. Operating mode Week program – Settings Can only be selected on HSP6, HSP8 and on HSP2 as an option oper. -
Page 11: Setting The Time And Date
9.1.2. Setting the time and date date/time fr, 13.09.2013 14:39:28 change Procedure: By pressing the “Ok” button on the right, the required date and time are set with the “Plus” and “Minus” buttons in the middle. The “Ok” button is used to switch from the date to the time setting. ... -
Page 12: Eco Mode
9.1.5. ECO mode main menu g002 ECO-Mode >yes ↓ Procedure: The required line can be selected with the “Plus” or “Minus” buttons. The setting is saved by pressing the “OK” button. To exit the function, press the “On/Off” button. 9.1.6. -
Page 13: Software Version Information
Procedure: The required value can be selected with the “Plus” or “Minus” buttons. The setting is saved by pressing the “OK” button. To exit the function, press the “On/Off” button. 9.1.9. Software version information Info Software SW-Version: HSP-6-V5.03 test date: 2015-02-11 ↓... -
Page 14: Heating Mode
10.2. Heating mode After the positive conclusion of the “Start phase”, the stove automatically switches to “Heating mode”. In “Heating mode”, the heat output of the stove is adjusted in modular fashion to the room temperature or to the difference between the ACTUAL and TARGET room temperatures. If the difference between the ACTUAL and TARGET room temperatures is big, then the stove heats with a bigger heat output. -
Page 15: Error Display - Fault
Once the switch-off process has ended, the error number is displayed under operating status in the FAULT menu. 10.9. Error display - Fault +++ error +++ ∓ 26°C 23°C F018 Quit. The stove can no longer be automatically started up. The operator can see the fault on the display. -
Page 16: Fault - Error Code Fxxx
14.1. Fault – error code Fxxx Code Cause: Correction: F001 STL triggered due to overheating If STB has triggered - contact service Fuse (F1) in the central unit is defective department Ignition short circuit Fuse F1(3.15 A) defective - contact service department Ignition defective - contact service department F002... - Page 17 F021 Burner dirty Clean burner Pellet tank empty Clean burner - fill pellet tank Downpipe / screw conveyor blocked Clean the intake on the screw conveyor housing with a vacuum cleaner. – Clean burner Room too airtight – required combustion Clean burner - Ensure adequate combustion air cannot flow into the room Flue gas temperature sensor defective...
-
Page 18: General Information / Faults
The receipt is to be presented as evidence. If a defect occurs in your appliance within the warranty period, HAAS + SOHN will correct (repair) this defect in the shortest possible time or optionally replace the defective item. Cancellation of the contract /a reduction in price is excluded in so far as this does not conflict with the statutory regulations.