Download  Print this page

Troubleshooting; Maintenance; Specifications - Aiwa CDC-X917M Operating Instructions Manual

Stereo car cd receiver.
Hide thumbs


Table of Contents
Random Play
You can play all the tracks on a CD in the disc magazine
in random order.
Press RNDM during CD Changer play.
"RANDOM" appears in the display.
To cancel Random Play, press RNDM again.
Pressing r during Random Play locates the beginning
of the current track. The unit does not retrieve previous
tracks during Random Play.
CD text information (Disc and Track title)
CD text information is available only if the optional AIWA
CD changer (ADC-EX108, etc.) which supports CD text,
is connected to this unit and a CD with CD text is played
on it.
Pressing DISP cycles through the items in the following
Radio/CD Play/CD Changer Play indication→Disc
title*→Track title*→Clock
* The CD text information is displayed only when it is


Error code
In the following cases the corresponding error code
indication appears. Follow the suggestions below to
solve such problems. If the error code indication does
not disappear, consult an AIWA service center.
ERROR01 The disc magazine is not properly inserted
in the CD Changer. Reinsert the magazine.
Refer to the instruction manual for the CD
ERROR02 No CDs are loaded in the disc magazine.
Insert CDs properly. Refer to the instruction
manual for the CD Changer.
ERROR03 Focus error. Check that the CD is loaded
properly (right side up, etc.), and the CD
contains valid data.
ERROR04 Problem with the CD Changer. Reset the
unit by pressing the reset button. If this does
not solve the problem, consult an AIWA
service center.
Reset button
If a CD does not operate properly, press the reset button
with a pointed object such as a pencil, etc. Note that all
your settings will be erased if this button is pressed.
Reset button


Cleaning the front panel
Wipe the surface with a soft, dry cloth.


Frequency Range: 87.5 MHz – 108 MHz (100-kHz
steps)* or 87.5 MHz – 108 MHz (50-kHz steps)*
Usable Sensitivity: 12.7 dBf
50 dB Quieting Sensitivity: 17.2 dBf
IF Rejection: 80 dB
Frequency Response: 30 Hz – 15,000 Hz
S/N Ratio: 63 dB
Stereo Separation: 35 dB at 1 kHz
Alternate Channel Selectivity: 70 dB
Capture Ratio: 3 dB
Frequency Range: 530 kHz – 1,710 kHz (10-kHz
steps)* or 531 kHz – 1,602 kHz (9-kHz steps)*
Usable Sensitivity: 30 µV (30 dB)
* Set the frequency increment for your area using
the switch on the bottom of the unit. (The switch
is factory-set to the 10k position [for the U.S.A.])
Frequency Response: 17 Hz – 20 kHz +0/–3 dB
Dynamic Range: More than 80 dB
Channel Separation: More than 65 dB
S/N Ratio: More than 85 dB
Wow/Flutter: Not applicable
Max. Power Output: 50 W × 4 channels
AUX IN input
Input sensitivity (load impedance) AUX IN: 300 mV
(10 kΩ)
Power-Supply Voltage: 14.4 V (11 to 16 V
allowable), DC, negative ground
Load Impedance: 4 Ω
Tone Control:
Bass ± 10 dB at 100 Hz, Treble ± 10 dB at 10 kHz
Preamp Output Voltage (load impedance): 4 V (10 kΩ)
Installed size: 182 (W) × 53 (H) × 155 (D) mm
(W) × 2
(H) × 6
(D) inches)



Table of Contents

Comments to this Manuals

Symbols: 0
Latest comments: