Download Print this page

Craftsman CMXEDAR300 Instruction Manual

Hide thumbs

Advertisement

Quick Links

10" (254 mm) Drill Press
10" (254 mm) Perforadora de columna
IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.
SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.
1-888-331-4569
INSTRUCTION MANUAL | MANUAL DE INSTRUCTIONES
WWW.CRAFTSMAN.COM
CMXEDAR300

Advertisement

loading

  Related Manuals for Craftsman CMXEDAR300

  Summary of Contents for Craftsman CMXEDAR300

  • Page 1 INSTRUCTION MANUAL | MANUAL DE INSTRUCTIONES 10" (254 mm) Drill Press 10" (254 mm) Perforadora de columna CMXEDAR300 IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US. SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS. 1-888-331-4569 WWW.CRAFTSMAN.COM...
  • Page 2 English (original instructions) Español (traducido de las instrucciones originales)
  • Page 3 Quill return coil/spring Chuck ON/OFF LED light switch if you have any questions or comments about this ON/OFF switch with product, call CRAFTsMAn toll free at: 1-888-331-4569. Depth stop nuts safety key Pulley cover Chuck key holder Belt tension lock knob...
  • Page 4: General Power Tool Safety Warnings

    English 10" (254 mm) Drill Press CMXEDAR300 GENERAL POWER TOOL SAFETY WARNINGS A moment of inattention while operating power tools may result in serious personal injury. WARNING: Read all safety warnings, b ) Use personal protective equipment. Always wear instructions, illustrations and specifications eye protection.
  • Page 5 English breakage of parts and any other condition • SECURE THE WORK. Use clamps or a vise to hold the that may affect the power tool’s operation. If work. It’s safer than using your hand and it frees both damaged, have the power tool repaired before hands to operate tool.
  • Page 6: Proposition 65 Warning

    English PROPOSITION 65 WARNING ELECTRICAL SPECIFICATIONS AND SAFETY WARNING: Drilling, sawing, sanding or machining Power Supply And Motor Specification wood products can expose you to wood dust, a WARNING: To avoid electrical hazards, fire hazards, substance known to the State of California to cause or damage to the tool, use proper circuit protection.
  • Page 7: Tools Needed For Assembly

    English and burning out of the motor. The table below shows the The label on your tool may include the following symbols. The correct size to use depending on cord length and nameplate symbols and their definitions are as follows: ampere rating. If in doubt, use the next heavier gauge. The V ......
  • Page 8: Carton Contents

    English CARTON CONTENTS UNPACKING YOUR DRILL PRESS Unpacking And Checking Contents Carefully unpack the drill press and all its parts, and compare against the list below and the illustration below. Place the drill press on a secure surface and examine it carefully. WARNING: To avoid injury from unexpected starting or electrical shock, do not plug the power cord into a source of power during unpacking and assembly.
  • Page 9: Assembly And Adjustments

    English WARNING: Many illustrations in this manual show 4. Slide the table with the rack onto the column. (Fig. G) only portions of the drill press. This is intentional so 5. Engage the bottom of the rack with the lip of the  17 ...
  • Page 10 English Installing The Chuck (Fig. L, M) Fig. H WARNING: Before any assembly of the chuck and arbor to the drill press head, clean all mating surfaces with a non petroleum based product; such as alcohol or lacquer thinner. Any oil or grease used in the packing of these parts must be removed otherwise the chuck may come loose during operation.
  • Page 11: Adjustments Instructions

    English Removing The Chuck (Fig. M) Adjustments Instructions 1. Turn the feed handles to lower the chuck to the lowest nOTE: All the adjustments for the operation of the drill position. press have been completed at the factory. Due to normal 2.
  • Page 12 English Belt Tension (Fig. S) 2. Turn the screw clockwise to eliminate the play, using a slotted screwdriver, but without obstructing the WARNING: To avoid injury from an accidental upward movement of the spindle. (A little play in the start, ALWAYS make sure the switch is in the "OFF" spindle is normal.) position, the switch key is removed, and the plug is not 3.
  • Page 13: Basic Drill Press Operation

    English OPERATION 3. To lock the switch in the OFF position, grasp the sides of the safety key, and pull it out. Basic Drill Press Operation 4. With the safety key removed, the switch will not turn WARNING: To avoid possible injury, keep guard the power tool on.
  • Page 14: Drilling To A Specific Depth

    English Fig. X Fig. Z Drill a Hole Using a centre punch or a sharp nail, make an indentation in the workpiece where you want to drill. Turn the power Drilling To a Specific Depth switch on and pull down on the feed handles with only enough effort to allow the drill to cut.
  • Page 15 English Feeding Fig. AA 1. Pull down the feed handles with only enough effort to allow the drill bit to cut. 2. Feeding too slowly might cause the drill bit to burn. Feeding too rapidly might cause the belt or drill to slip, tear the workpiece loose or break the drill bit.
  • Page 16: Free Warning Label Replacement

    English MAINTENANCE Free Warning Label Replacement WARNING: For your own safety, turn the switch If your warning labels become illegible or are missing, call off and remove the plug from the power source 1-888-331-4569 for a free replacement. outlet before maintaining or lubricating your drill press.
  • Page 17: Troubleshooting Guide

    TROUBLESHOOTING GUIDE BE sURE TO FOllOW sAFETY RUlEs AnD insTRUCTiOns For assistance with your product, visit our website at www.craftsman.com for a list of service centers, or call CRAFTSMAN at 1-888-331-4569. PlEAsE READ ThE FOllOWing: The manufacturer and/or distributor is providing the buyer with a parts list and assembly diagram in this manual as a reference tool only.
  • Page 18: Register Online

    90 DAY MOnEY BACK gUARAnTEE If you are not completely satisfied with the performance of your CRAFTSMAN Power Tool, Laser, or Nailer for any reason, you can return it within 90 days from the date of purchase with a receipt for a full refund – no questions asked.
  • Page 19: Parts List

    English PARTS LIST 10" (254 mm) Drill Press Parts list for drill press i.D. nO. Description size Q’ty i.D. nO. Description size Q’ty X759 BATTERY X77L CR. RE. COUNT HD. SCREW M6*1.0-12 X75A SWITCH BASE X77M CLAMP CORD X75C POWER CORD X77N CR.
  • Page 20 English 10" (254 mm) Drill Press schematic for drill press X83N X84C X77K X84B X83G X83H X77N X77A X77M X83P X83Z X7B8 X848 X83R X83F X77L X77J X83L X83M X77L X77B X77D X77C X77H X847 X77E X846 X84C X76L X779 X778 X774 X77N...