Related Manuals for Westinghouse Urban Gale
Summary of Contents for Westinghouse Urban Gale
- Page 1 SAA-Urban Gale-Australia-WH18 OWner'S MAnUAl Urban Gale Please write model number here for future reference: 7202135 net Weight: 5.0 KGS 240V~50Hz...
-
Page 2: Safety Tips
SAA-Urban Gale-Australia-WH18 SAfETy TIpS READ AND SAVE THESE INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Proceed with caution. Read all instructions before beginning the installation. 2. Only an authorized electrician should execute the installation. -
Page 3: Installation
SAA-Urban Gale-Australia-WH18 Features DOWNROD VAULTED CEILING INSTALLATION INSTALLATION For normal ceilings May require a longer downrod (sold separately) -
Page 4: Preparing For Installation
SAA-Urban Gale-Australia-WH18 PrePArInG fOr InStAllAtIOn Use metal outlet box suitable for fan support (must support 35 lbs). Before attaching fan to outlet box, ensure the outlet box is securely Unpack and inspect fan carefully to be certain all contents are included. Turn off fastened by at least two points to a structural ceiling member (a loose power at fuse box to avoid possible electrical shock. -
Page 5: Mounting Bracket Installation
SAA-Urban Gale-Australia-WH18 MOUntInG brACKet InStAllAtIOn WIrInG OPtIOnS Wiring: TERMINAL BLOCK From House: Connector: Fan Live (L) Neutral (N) Ground Follow diagram above to make wiring connections to the terminal block on the mounting bracket. Install mounting bracket to outlet box in ceiling using the screws and wash-... - Page 6 SAA-Urban Gale-Australia-WH18 MOuNtING With bracket holding fan assembly, attach the male/female plug connection (1) from Carefully lift fan assembly onto mounting bracket. Rotate fan until notch on down- the fan to the terminal block. Attach the ground wire (2) from the downrod rod ball (1) engages the ridge on the mounting bracket (2).
- Page 7 SAA-Urban Gale-Australia-WH18 PrePArInG fOr InStAllAtIOn For downrod fans, slide the canopy up to the mounting bracket. The canopy has two mating slots (1) and two mating holes (2). Position both slots on canopy directly under and in line with two screws in the mounting bracket (3). Lift the canopy, allowing the two screws to slide into the mating slots.
- Page 8 SAA-Urban Gale-Australia-WH18 PrePArInG fOr InStAllAtIOn Loosen set screw in lower canopy and slide to within 1/4”/7mm of the motor. Tighten set screw(s) in the lower canopy. Make sure there is at least 1/4”/7mm clearance maintained around the motor and lower canopy.
-
Page 9: Blade Installation
SAA-Urban Gale-Australia-WH18 blAde InStAllAtIOn Install blades to top of motor using screws and washers . See above Attach blade brackets to blades using the blade bracket screws (1), drawing for reference. metal washers (2), and nuts (3). -
Page 10: Wall Control Installation
SAA-Urban Gale-Australia-WH18 WAll COntrOl InStAllAtIOn Remove the front cover of the wall control by unsnapping the cover (1) from the control unit (2). - Page 11 SAA-Urban Gale-Australia-WH18 WIrInG tO tHe WAll COntrOl Connect the fan control wire from the fan to the terminal block on the wire marked “For fan-L”, as line art shown on “1”; Connect the 240V hot house wire to the terminal block on the wire marked “TO AC-L240V/50HZ”, as line art shown on “2”.
- Page 12 SAA-Urban Gale-Australia-WH18 OPerAtIOn WAll COntrOl InStAll WAll COntrOl tO OUtlet bOx Operation: Fan Rotary Control OFF - Fan Speed OFF 3 - Fan Speed HIGH 2 - Fan Speed MEDIUM 1 - Fan Speed LOW When wiring is complete, make sure no bare wires are exposed from the terminal connections on the back of the fan control unit.
- Page 13 SAA-Urban Gale-Australia-WH18 InStAll WAll COntrOl tO OUtlet bOx Replace the front cover of the wall control unit by snapping the cover (1) onto the control unit (2).
-
Page 14: Troubleshooting Guide
SAA-Urban Gale-Australia-WH18 If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some cases, these trOubleshOOtING GuIde installation errors may be mistaken for defects. If you experience any faults, please check this Troubleshooting chart. If a problem cannot be remedied, please consult with your authorized electrician and do not attempt any electrical repairs yourself. -
Page 15: Parts List
SAA-Urban Gale-Australia-WH18 Parts lIst description 1 ..... . Mounting Bracket 2 ..... . Blade Bracket 3 . - Page 16 SAA-Urban Gale-Australia-WH18 Westinghouse Lighting, Philadelphia, PA 1029-19154, U.S.A. www.westinghouselighting.com , WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF are trademarks of Westinghouse Electric Corporation. Used under license by Westinghouse Lighting AS/NZS Approval No. All rights reserved. SAA-181731-EA Made in China...