Page 1
E À S AJ U IL U TI ÉR L' H S EL D IÉ E DE T EN E L'A 89212060-1 ® ® FOR TECHNICAL ASSISTANCE OR THE HOTSY DEALER NEAREST YOU, VISIT OUR WEB SITE AT WWW.HOTSY.COM 8.921-206.0...
The model and serial numbers will be found on a decal attached to the pressure washer. You should record both serial number and date of purchase and keep in a safe place for future reference. HOTSY 800 OIL FIRED • 8.921-206.0 • Rev. 3/13...
9. Never run pump dry or leave spray gun closed to a power supply receptacle protected by a GFCI. longer than 1-2 minutes. 10. Keep operating area clear of all persons. HOTSY 800 OIL FIRED • 8.921-206.0 • Rev. 3/13...
Page 6
TRIGGER GUN KICKS tion. BACK - HOLD WITH the influence of alcohol, prescription medications, 14. Be certain all quick coupler fit- BOTH HANDS or drugs. tings are secured before using pressure washer. HOTSY 800 OIL FIRED • 8.921-206.0 • Rev. 3/13...
Page 7
IMPORTANT SAFETY INFORMATION Brake 89212060-27 Follow the maintenance instructions WARNING: To prevent damage or injury. specified in the manual. Keep brake engaged during machine operation and storage. HOTSY 800 OIL FIRED • 8.921-206.0 • Rev. 3/13...
GFCI — Provided on all single phase machines. Trips when there is current leakage. Hose Reel Bracket — Mounts optional hose reel. Relief Valve — Ruptures when pressure exceeds 7000 psi. HOTSY 800 OIL FIRED • 8.921-206.0 • Rev. 3/13...
#1 or #2 smoke spot plugged into an appropriate outlet that is properly installed on the Bacharach scale. and grounded in accordance with all local codes and ordinances. HOTSY 800 OIL FIRED • 8.921-206.0 • Rev. 3/13...
Page 12
WARNING: To reduce the risk of electrocution, keep all connections dry and off the ground. DO NOT touch plug with wet hands. HOTSY 800 OIL FIRED • 8.921-206.0 • Rev. 3/13...
Turn off burner and shut off fuel supply. Have cause of Pressure Nozzle failure corrected by an authorized service technician before use of pressure washer is continued. Manual Trigger Lock 89212060-29 HOTSY 800 OIL FIRED • 8.921-206.0 • Rev. 3/13...
Page 14
For the best results, reduces your cleaning power. Wash at a 30° to 60° contact your Hotsy dealer to help you select the best angle to the work. This will allow the water to splash detergent for your application.
Page 15
NOTE: For a more gentle rinse, select the white 40° nozzle. To scour the surface, select the yellow 15° or red 0° nozzle. HOTSY 800 OIL FIRED • 8.921-206.0 • Rev. 3/13...
When the water reaches this temperature, the pump protector engages and cools the pump by discharging the warm water onto the ground. This thermal device prevents internal damage to the pump. HOTSY 800 OIL FIRED • 8.921-206.0 • Rev. 3/13...
3. Cover the pressure washer and store in a clean, dry time, it is recommended that the system be flushed place that is well ventilated away from open flame with antifreeze for rust protection. or sparks. HOTSY 800 OIL FIRED • 8.921-206.0 • Rev. 3/13...
Pump Relief Valve Use Hotsy Pump Oil P/N 315068 or equivalent 30W non-detergent oil for pump crankcase. Crankcase must be WARNING: The relief valve on this pressure washer filled to the full mark on the dipstick or to center of sight has been factory set and sealed and is a field nonad- glass window found on the rear of the pump.
Refill detergent container. Ensure that pick-up DETERGENT screen is full immersed. Open metering valve. FLOW Detergent screen or hose Clean. Always start with a clean detergent clogged container. Clogged detergent valve Clean. HOTSY 800 OIL FIRED • 8.921-206.0 • Rev. 3/13...
Page 20
IMPORTANT If the pressure washer demonstrates other symptoms or the corrective actions listed do not correct the problem, contact the local authorized Hotsy Service Center. The Hotsy Service Center can be identified by visiting www.hotsy.com. When ordering from your dealer, please provide the following:...
Page 21
Hotsy does not authorize any other party, including authorized Hotsy Distributors, to make any representation or promise on behalf of Hotsy, or to modify the terms, conditions, or limitations in any way. It is the buyer’s responsibility to ensure that the installation and use of Hotsy products conforms to local codes.
Page 22
If you are looking for replacement parts for your Hotsy, please contact your local dealer. You can find a dealer by calling Hotsy at 800-525-1976 or by visiting www.hotsy.com.
Page 23
If you need service on your pressure washer, contact your local Hotsy dealer or visit www.Hotsy.com. Smart phone users scan the code below to link directly to the Service Request page. Form #8.921-206.0 • Revised 3/13 • Printed in U.S.A.