Technical Data; Eu Declaration Of Conformity; Statement Of Use; Product Specific Instructions - Chicago Pneumatic SQUEEZER CP4210CS Operator's Manual

Technical data

@ Max. pressure: 6.3bar (90psi)
kg
CP4210AL 2.1
CP4220AL 2.5
CP4210CS 2.04
CP4220CS 2.49
CP4210AS 1.7
CP4220AS 2.2
(dB(A))
CP4210AL 76
CP4220AL 72
CP4210AS 76
CP4220AS 72
CP4210CS 76
CP4220CS 77
Declarations
Noise and vibration
Uncertainty 3 dB(A), in accordance with EN ISO 15744. For
Sound power level, add 11 dB(A)
Vibration standard : EN ISO 20643
These declared values were obtained by laboratory type test-
ing in accordance with the stated standards and are suitable
for comparison with the declared values of other tools tested
in accordance with the same standards. These declared val-
ues are not adequate for use in risk assessments and values
measured in individual work places may be higher. The ac-
tual exposure values and risk of harm experienced by an indi-
vidual user are unique and depend upon the way the user
works, the workpiece and the workstation design, as well
upon the exposure time and the physical condition of the
user.
We, CHICAGO PNEUMATIC Tool Co. LLC, cannot be
held liable for the consequences of using the declared values,
instead of values reflecting the actual exposure, in an individ-
ual risk assessment in a work place situation over which we
have no control.
This tool may cause hand-arm vibration syndrome if its use
is not adequately managed. An EU guide to managing hand-
arm vibration can be found by accessing
www.pneurop.eu/index.php
lation'.
We recommend a programme of health surveillance to detect
early symptoms which may relate to noise or vibration expo-
sure, so that management procedures can be modified to help
prevent future impairment.
6
lb
4.5
5.5
4.5
5.5
3.75
4.75
2 2
(m/s ) K (m/s
2.7 <2.5
1.6 <2.5
2.7 <2.5
1.6 <2.5
2.3 <2.5
1.4 <2.5
http://
and selecting 'Tools' then 'Legis-
© Chicago Pneumatic - 6159924730
If this equipment is intended for fixtured applications:
The noise emission is given as a guide to the machine-
builder. Noise and vibration emission data for the com-
plete machine should be given in the instruction manual
for the machine.

EU DECLARATION OF CONFORMITY

We, CHICAGO PNEUMATIC Tool Co. LLC, 1815 Club-
house Road, Rock Hill, SC 29730, declare under our sole re-
sponsibility that the product (with name, type and serial
number, see front page) is in conformity with the following
Directive(s):
2006/42/EC (17/05/2006)
Harmonized standards applied:
EN ISO 11148-10 : 2011
Authorities can request relevant technical information from:
)
Pascal Roussy, R&D Manager, Ets Georges Renault, 38 rue
Bobby Sands, BP10273 44818 Saint Herblain, France
Saint-Herblain,
Pascal ROUSSY
Signature of issuer

Statement of use

This tool is intended for riveting using rivet set shank diame-
ter 0.1875" (4.8mm). No other use permitted. For profes-
sional use only.

Product specific instructions

Operation
The throttle lever (A) must first be moved forward axially
before depressing to start cycle. This is a safety feature to re-
duce accidental actuations. Once throttle lever is depressed,
compressed air forces the piston and wedge forward, then
one rivet set is driven toward the other exerting compressive
force on the rivet. Force is exerted until the throttle lever is
released, returning the tool to the ready position ending its
cycle of operation.
Lubrication
Daily before using, before putting a new or an old tool into
service, and after each shift, disconnect tool, blow out air line
to clean it of accumulated dirt and moisture. Pour about 1/2
fl. oz. (14 ml) of recommended oil into air inlet. Connect tool
and operate to allow oil to be carried to cylinder. In addition,
the use of a Air Line Lubricator installed at the end of each
air pipe leading to this pneumatic tool is recommended to as-
sure a constant and adequate supply of lubricant to valves
and cylinder.
SQUEEZER