Page 1
PANEL PC 1150 All-in-One 15.1” Super Slim PANEL PC User’s Manual...
Page 2
ACNODES Corp. assumes no responsibility for any inaccuracies that may be contained in this document. ACNODES Corp. makes no commitment to update or to keep current the information contained in this manual.
Page 3
CE Marking FCC Class A FCC Compliance This equipment has been tested and complies with the limits for a Class-A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Before getting started, read the following important cautions. 1. The PANEL PC 1150 does not come equipped with an operating system. An operating system must be loaded first before installing any software into the computer. 2. Be sure to ground yourself to prevent static charge when installing the internal components.
Page 5
When handling boards and components, wear a wrist-grounding strap, available from most electronic component stores. Trademarks Acknowledgments ACNODES is a trademark of ACNODES Corp. IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation. Intel and Pentium are trademarks of Intel Corporation.
Page 6
This page does not contain any information.
PANEL1150-370 15.1” All-in-One PANEL PC User’s Manual This chapter contains the general information and the detailed specifications of the PANEL PC 1150. Chapter 1 includes the following sections: General Description System Specification Dimensions General Description The PANEL PC 1150 super slim industrial PANEL PC is mainly designed for industrial automation and some space-constricted embedded applications.
PANEL1150-370 15.1” All-in-One PANEL PC User’s Manual Specifications 1.2.1 Core System for PANEL PC 1150 CPU: Intel Celeron 300 up to 733 MHz; Intel Pentium III 500 up to 850 MHz System Chipset: Intel 440BX Core Logic Controller BIOS: Award BIOS, Y2K compliant...
PANEL1150-370 15.1” All-in-One PANEL PC User’s Manual 1.2.4 System Specification 15.1” TFT with 1024 x 768 resolution NEMA 4/12 sealed front panel 24X slim type CD-ROM drive 2.5” floppy disk drive Heat dispensing design PC/104 expansion Bus Two free slots for PCI/ISA and ISA expansion, or two free slots for PCI/ISA and PCI expansion This slot only comes standard with the riser card assembly.
PANEL PC 1150 15.1” All-in-One PANEL PC User’s Manual Dimensions The following diagrams show the dimensions and outlines of PANEL PC 1150. Introduction...
Page 14
PANEL1150-370 15.1” All-in-One PANEL PC User’s Manual Introduction...
PANEL PC 1150 15.1” All-in-One PANEL PC User’s Manual I/O Outlets The following figure shows the I/O arrangement of the PANEL PC 1150. The backside of the chassis contains most of the connectors. Introduction...
PANEL1150-370 15.1” All-in-One PANEL PC User’s Manual C h a p t e r System Configuration This chapter details the system parts and components with figures. Sections include System Major Parts Panel Mount System Configuration 2.1.1 Front View The figure below shows the features and controls on the PANEL PC 1150 front panel.
PANEL1150-370 15.1” All-in-One PANEL PC User’s Manual Panel Mount The PANEL PC 1150 is mainly designed for panel mount application. To mount the PANEL PC 1150, the standard set of mounting kit (included in the system packaging) is needed. Please refer to the following figure.
PS/2 Mouse Parallel Port The PANEL PC 1150 has a Pentium III little board with a free ISA and PCI slots inside the riser card assembly. It already builds in a Pentium III CPU, relevant DRAM and a 3.5” HDD (or a 2.5” optional HDD).
PANEL1150-370 15.1” All-in-One PANEL PC User’s Manual CPU, HDD, and DRAM Installation The standard PANEL PC 1150 system already builds in a Pentium-level CPU, and a 3.5” (or optional 2.5”) hard disk drive. SBC8360, on the one hand, provide one 168-pin DIMM socket that supports system memory up to 256MB.
PANEL1150-370 15.1” All-in-One PANEL PC User’s Manual 1. Remove the 3 screws securing the riser card assembly’s back cover. Take off the cover by sliding it outward and pulling it upwards as pointed by the arrows. If your system does not come with a riser card assembly, proceed to step 2.
Page 22
PANEL1150-370 15.1” All-in-One PANEL PC User’s Manual 4. See the illustration for the exact locations of your CD-ROM and FDD slots. There are 2 screws mounted on the cover of each slot. Remove these screws. Store the covers at a safe place for future use. 5.
PANEL1150-370 15.1” All-in-One PANEL PC User’s Manual 3 x Serial Ports The PANEL PC 1150 provides four onboard serial ports installed on the back bottom side of the chassis. For systems, COM1 and COM2 are RS-232 and COM4 is RS-232/422/485. Each serial port is with...
PANEL1150-370 15.1” All-in-One PANEL PC User’s Manual The PANEL PC 1150 has an analog RGB interface connector. It is able to connect to an expansion CRT monitor, and the system can display on both the flat panel and the CRT simultaneously.
PANEL1150-370 15.1” All-in-One PANEL PC User’s Manual Digital I/Os The PANEL PC 1150 provides a digital I/O of 4-channel inputs/outputs for simple automation control. For example, it can be used to control the opening and closing of the cash drawer on a POS system. It can also be used for UPS control.
The main section has 3 internal and 3 external screws that lock the assembly tightly on the PANEL PC 1150. The lid on the other hand, also has 6 screws that hold it to the main section, 3 on each side.
Screw the lid back to the main section by fastening 3 more screws located on top of the cover. 3.10 PS/2 Mouse The PANEL PC 1150 has one PS/2 mouse connector. A simple plug-in will make the connection. System Installation...
PANEL1150-370 15.1” All-in-One PANEL PC User’s Manual 3.11 System O/S and Software Installation The PANEL PC 1150 is not equipped with any operating system. It builds in a 3.5” (or optional 2.5”) HDD. Device is built in the system chassis, to load any O/S or application software into the computer. an external device is needed to act as a bridge.
PANEL1150-370 15.1” All-in-One PANEL PC User’s Manual Power Supply Specifications The power supply used in the PANEL PC 1150 is a 100W open frame power supply. The specifications and features of this special power supply are listed in the following sections.
PANEL1150-370 15.1” All-in-One PANEL PC User’s Manual Environmental Specifications Operating temperature range: 0 C to 50 C Storage temperature range: -40 C to +85 C Humidity, non-condensing: Altitude: 0 to 10,000 feet International Standards Safety Standards Designed to meet the following standards: UL 1950, CSA 22.2 NO.