Related Manuals for netvox R718WB
Summary of Contents for netvox R718WB
- Page 1 Model：R718WB Wireless Water Leak Detector with Rope Sensor Wireless Water Leak Detector with Rope Sensor R718WB User Manual...
-
Page 2: Table Of Contents
Table of Content 1. Introduction ................................2 2. Appearance ................................2 3. Main Features ................................3 4. Set up Instruction ..............................4 5. Data Report ................................5 6. Installation ................................8 7. Information about Battery Passivation ......................... 10 8. Important Maintenance Instruction ........................11... -
Page 3: Introduction
1. Introduction R718WB is a LoRaWAN device compatible with LoRaWAN protocol (ClassA). When the R718WB sensor detects a leak, it will send an alarm message to the gateway. When the sensor detects no leaks, it will send a message that shows no leak to the gateway. -
Page 4: Main Features
Applicable to third-party platforms: Actility/ThingPark, TTN, MyDevices/Cayenne Low power consumption and long battery life Note: Battery life is determined by the sensor reporting frequency and other variables, please refer to http://www.netvox.com.tw/electric/electric_calc.html On this website, users can find battery life of various models in different configurations... -
Page 5: Set Up Instruction
4. Set up Instruction On/Off Power on Insert batteries. (users may need a screwdriver to open) Turn on Press and hold the function key for 3 seconds till the green indicator flashes once. Press and hold the function key for 5 seconds till the green indicator flashes for 20 Turn off (Restore to factory setting) times. -
Page 6: Data Report
When the R718WB status changes, it will send warning report. No water leak:0 Water leak:1 The reported data is decoded by the Netvox LoRaWAN Application Command document and http://www.netvox.com.cn:8888/page/index Data report configuration and sending period are as following: Current Change＜... - Page 7 MaxTime BatteryChange Reserved 0x01 tReq (2bytes Unit:s) (2bytes Unit:s) (1byte Unit:0.1v) (4Bytes,Fixed 0x00) ConfigRepor Status Reserved 0x81 tRsp (0x00_success) (8Bytes,Fixed 0x00) R718WB 0x12 ReadConfig Reserved 0x02 ReportReq (9Bytes,Fixed 0x00) ReadConfig MinTime MaxTime BatteryChange Reserved 0x82 ReportRsp (2bytes Unit:s) (2bytes Unit:s) (1byte Unit:0.1v)
- Page 8 Example for MinTime/MaxTime logic: Example#1 based on MinTime = 1 Hour, MaxTime= 1 Hour, Reportable Change i.e. BatteryVoltageChange=0.1V MaxTime MaxTime Sleeping(MinTime) Sleeping(MinTime) Wake up and collects data Wakes up and collects data Wakes up and collects data REPORTS 3.6V REPORTS 3.6V REPORTS 3.6V Note: MaxTime=MinTime.
-
Page 9: Installation
6. Installation This product comes with waterproof function. When using it, the back of it can be adsorbed on the iron surface, or the two ends can be fixed to the wall with screws. Note: When installing the battery, use a screwdriver or similar tool to assist in opening the battery cover. Waterline Structure: Leakage Rope Length: Up to 300m* Water contacting alarm: At least 3 cm line length... - Page 10 (susceptible to interference) (susceptible to damage cable) (damp to false alarm ) Time : Instant (Within 10 seconds) R718WB cable clip Water >3cm Soaking water >3cm,Send a Report Water Soaking depth > 2mm...
-
Page 11: Information About Battery Passivation
Information about Battery Passivation Many of Netvox devices are powered by 3.6V ER14505 Li-SOCl2 (lithium-thionyl chloride) batteries that offer many advantages including low self-discharge rate and high energy density. However, primary lithium batteries like Li-SOCl2 batteries will form a passivation layer as a reaction between the lithium anode and thionyl chloride if they are in storage for a long time or if the storage temperature is too high. -
Page 12: Important Maintenance Instruction
8. Important Maintenance Instruction Kindly pay attention to the following in order to achieve the best maintenance of the product: • Keep the device dry. Rain, moisture, or any liquid, might contain minerals and thus corrode electronic circuits. If the device gets wet, please dry it completely.