Table of Contents
Advertisement
CAUTION
Before moving the appliance make sure
the load bearing capacity of the lifting
equipment used is suitable for its weight.
E.2
Customer's responsibilities
The tasks and works required of the Customer are:
• prearrange a high-sensitivity manual-reset magneto-ther-
mal circuit-breaker;
• prearrange a device lockable in the open position for the
connection to the power supply.
• check the floor planarity on which the machine is placed.
• install a rapid gas shutoff valve ahead of each individual
appliance (depending on the model). Install the valve in an
easily accessed place.
• for information regarding the electrical connection, refer to
E.10.1 Electric appliances paragraph;
E.3
Disposal of packing
The packing must be disposed of in compliance with the
current regulations in the country where the appliance is used.
All the packing materials are environmentally friendly.
They can be safely kept, recycled or burned in an appropriate
waste incineration plant. Recyclable plastic parts are marked
as follows:
Polyethylene
• Outer wrapping
• Instructions bag
Polypropylene
• Straps
Polystyrene foam
• Corner protectors
The parts in wood and cardboard can be disposed of,
respecting the current regulations in the country where the
machine is used.
E.4
Joining Appliances
1. Undo the 4 fixing screws;
2. Remove the control panels of the appliances (Fig.1A);
3. Remove the fixing screw nearest the control panel, from
each side to be joined (Fig.1B);
4. Bring the appliances together;
5. Turn the feet to level them until the tops match;
6. Turn one of the two plates inside the appliances 180℃
(Fig.1C);
7. From inside the control panel of the same appliance, join
them at the front side, screwing one M5x40 Hex Head
screw (supplied) on the opposite insert (Fig.1E);
8. From the rear of the appliances, insert the coupling plate
(provided) in the side slots on the back panels;
16
1B
1C
1A
9. Secure the plate with two flat head M5 screws provided
(Fig.1F).
1F
E.4.1
Installation On Bridge or Cantilever Frame
(depending on the appliance and/or model)
• Carefully follow the instructions enclosed with the corre-
sponding accessory.
• Follow the instructions supplied with the optional product
chosen.
E.4.2
Sealing Gaps Between Appliances
Follow the instructions supplied with the optional sealing paste
pack.
E.5
Gas, electricity, water and other
connections (if present, depending on the
appliance and/or model)
• Any installation work or maintenance to the supply system
(gas, electricity, water and/or steam, if present) must only
be carried out by the utility company or an authorised
installation technician.
• Refer to the appliance dataplate for the product code.
• See the installation diagram for the type and position of
appliance connections.
E.6
Gas Connections
E.6.1
Introduction
CAUTION
This appliance is arranged and tested to
operate with G20 gas 20 mbar;
To convert it to another type of gas, follow the instructions in
E.6.6 Conversion to another type of gas paragraph of this
section.
E.6.2
Fume exhaust
• "A1" type appliances have to be positioned under an
extraction hood to ensure removal of fumes and steam
produced by cooking;
(not relevant for Australian standard).
For AUSTRALIA: the ventilation must be in accordance with
Australian building codes and kitchen exhaust hoods must
comply with AS/NZS1668.1 and AS 1668.2.
E.6.3
Before connecting
1. Make sure the appliance is arranged for the type of gas to
be used.
Otherwise, carefully follow the instructions given in E.6.6
Conversion to another type of gas paragraph of this
section.
2. Fit a rapid gas shutoff tap/valve ahead of each appliance.
1E
Advertisement
Table of Contents
