DBL Technology GoIP-1 User Manual page 14

https://arttel.ru/
DBL Technology Co., Ltd.
www.dbltek.com
Here are the list of the device parameters shown in this page.
1. CH – This column allows selection of channels for Reset functions. Selection can be done by clicking
each box individually or the
reset the corresponding parameters.
2. Line – This column refers to both the physical GSM channels and VoIP lines
3. M – This column shows the power status of the all GSM modules. "Y" means that the power to the
GSM module is on. "N" means that the power to the GSM module is off. Click on "Y" to turn off the
power to the corresponding GSM module or vice versa.
4. SIM – This shows the SIM card status. "Y" means that the corresponding GSM module can access
the designated SIM card successfully. "N" means unable to access the designated SIM card. Please
check if the SIM card is inserted properly or the SIM card is damaged. If Remote SIM function is used,
please check the SIM Bank and/or SIM Server configuration. The problem could also be caused by bad
network condition or improper network configuration.
5. GSM – GSM registration status. "Y " means "Registered" and "N" means "Not Registered".
6. VoIP – VoIP registration status. "Y " means "Registered" and "N" means "Not Registered". If GSM
Registration status is "N", VoIP registration is disabled and its status should be ignored.
7. Status – VoIP line status. If VoIP registration status is "N", the VoIP line status shown should be
ignored. Once VoIP registration status is "Y", the current VoIP line status is then shown in this field.
Here are a list of available statuses:
a. IDLE – The VoIP line is not engaged in any call activities.
b. CONNECTED – An active call between VoIP and GSM is in progress.
c. ACTIVE – A second dial tone is generated when a VoIP call is answered without making a GSM call
or when a GSM call is answered without making a VoIP call. The generation of a second dial tone
prompts the caller to press a phone number. The "Status" changes to "ACTIVE" since the start of
the second dial tone till a phone number is received for dialing or the call is terminated.
d. DIALING <phone number> – This occurs when the GoIP is dialing out a phone number via the
corresponding GSM channel or The DIALING status shows that a number is being dialed out via the
corresponding GSM channel or a VoIP line. The phone number dialed is also shown in the "Status".
e. ALERTING – After a phone number is dialed, the "Status" changes to "ALERTING" when a ringback
signal is received from the network.
f. INCOMING – This occurs when a GSM incoming call is calling and the call is not answered yet.
8. SMS - SMS Server registration status. "Y " means "Registered" and "N" means "Not Registered". If SMS
Server is diabeled, no status (blank) is displayed.
9. ACD(s) - This shows the Average Call Duration (s)
10. ASR(%) – This shows the Answer Seizure Ratio (%)
11. Duration – This shows the Total Call Duration
12. Count – This shows the number of successful calls
13. CDR Start – This shows the starting time for calculating the CDR.
14. RSSI – This indicates the Received Signal Strength Indicator of the current cell. Its normal range is from
0 to 31 which represents a signal level ranging from -113 dBm to -51 dBm; each increment in rssi values
means 2 dBm increment. 99 means that the signal level is unknown or undetected.
15. Carrier – This shows the name of the current GSM carrier.
16. BTS ID – This shows the Base Transceiver station (BTS) ID.
17. Idle – This shows the time elapsed since the last call.
18. Remain – This shows the time remaining if the Total Talk Time Limit (m) is set. Once the Remain
time reaches zero, the corresponding channel is locked and its VoIP registration is also suspended (default
setting). However, there is an option in Section 3.3.10 to enable SIP registration even when the Talk
Time Limit expires ((Remain = 0).
19. Reset – This columns contains 3 icons (
to the preset values.

https://arttel.ru/shop/gsm-shlyuzy/gsm-shlyuz-goip-4
box for all channels. Then pressing the reset icons at the bottom to
is the icon for resetting talking time remaining. When the accumulative talk time reaches
GoIP User Manual
Technical Support: support@dbltek.com
) to reset Remain, SMS, and ACD/ASR
14