Table of Contents
Advertisement
Quick Links
Instruction - Parts
C
Solar Control Box
For accurately metering and injecting chemicals at well sites. For professional use only.
See page 3 for model information.
Important Safety Instructions
Read all warnings and instructions in this manual
and other related manuals on page 2 before using
the equipment. Save these instructions.
3A5083C
EN
Advertisement
Table of Contents
Related Manuals for Graco B52100
Summary of Contents for Graco B52100
- Page 1 Instruction - Parts 3A5083C Solar Control Box For accurately metering and injecting chemicals at well sites. For professional use only. See page 3 for model information. Important Safety Instructions Read all warnings and instructions in this manual and other related manuals on page 2 before using the equipment.
-
Page 2: Table Of Contents
Before Installing ......9 Graco Standard Warranty ....16 Attach Metal Box to Pole (Optional) . -
Page 3: Single Plastic Battery Box Configuration Number Matrix
Single Plastic Battery Box Configuration Number Matrix Single Plastic Battery Box Configuration Number Matrix Check the identification plate (ID) for the 12-digit Configuration Number of your box. Use the following matrix to define the components of your box. NOTE: Not all possible configurations are available. Sample Configuration Number: CI-P12-1111-00 Chemical Box Style... -
Page 4: Warnings
Warnings Warnings The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama- tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this manual where applicable. - Page 5 Warnings PERSONAL PROTECTIVE EQUIPMENT Wear appropriate protective equipment when in the work area to help prevent serious injury, including eye injury, hearing loss, inhalation of toxic fumes, and burns. Protective equipment includes but is not limited to: • Protective eyewear, and hearing protection. •...
-
Page 6: Installation
Installation Installation Grounding The equipment must be grounded to reduce the risk of static sparking. Static sparking can cause fumes to ignite or explode. Grounding provides an escape wire for the electric current. Plastic Box: Contains ground lug (see Parts on page 13). -
Page 7: Typical Installation
Pump (includes Inlet (K) and Outlet (L) ports) The following components, see F . 1, are supplied by Solar Panel Graco with the Modular System DC control box: Stand Unit Tank Control Box (batteries provided by customer) Pressure Relief Valve... -
Page 8: Wiring And Fuse Diagram
Installation Wiring and Fuse Diagram Incorrect wiring to the charge controller or battery may result in an electrical or fire risk, and can damage the equipment. The following wiring diagram shows the locations of the fuses (F1, F2, and F3) used with the Harrier EZ and EZ-JR controllers. -
Page 9: Setup And Operation
Setup and Operation Setup and Operation Incorrect wiring to the charge controller or battery may result in an electrical or fire risk, and can damage the equipment. Before Installing 2. Using two U-bolts (B1), and their corresponding mounting plates (B2) and nuts (B3), loosely attach the control box (B) to the pole (S). -
Page 10: Pump Installation
Setup and Operation Pump Installation Controller Installation and Operation Refer to your pump manual for pump installation. (See Related Manuals on page 2.) Refer to your controller manual for controller installation and operation. (See Related Manuals on page 2.) Verify that the fuses are removed before attaching pump wires. -
Page 11: Maintenance
• See Fuse Ratings on this page for current ratings. Replacement fuses are available from Graco. • Voltage Rating: 32 VDC • Current Rating: See Fuse Ratings on this page •... -
Page 12: Troubleshooting
Troubleshooting Troubleshooting Problem Cause Solution System stops running Battery charge too low Charge battery. Replace if problem persists. Fuse blown Replace fuse with like kind. Find short if problem persists. NOTES: • Refer to your pump manual (see Related Manuals on page 2) for troubleshooting specific to the pump. -
Page 13: Parts
Parts Parts Plastic Control Box Single Metal Battery Box and Solar Panel Kit Part No. B52100 is shown Part No. 25T564/25T620 is shown Single Metal Battery Box and Solar Panel Kit Parts List Ground Lug Ref. Part Description Plastic Control Box Parts List... -
Page 14: Kits And Accessories
Parts Kits and Accessories Part No. Description B32016 50 W Solar Panel, ordinary location B32014 100 W Solar Panel, ordinary location B32021 160 W Solar Panel, ordinary location B32018 50 W Solar Panel, C1D2 B32017 90 W Solar Panel, C1D2 B32751 150 W Solar Panel, C1D2 B32729... -
Page 15: Technical Specifications
Technical Specifications Technical Specifications Solar-Powered Chemical Injection Systems Metric Nominal Voltage 12 V Maximum Solar Input Current ASC 12/8 ASC 12/12 12 A Maximum Load Current 16 A Battery Size Designed for a maximum of one Group 31 battery. Operating Temperature Range Plastic Control Box 32 - 131°F 0 - 55°C... -
Page 16: Graco Standard Warranty
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.