Koso 10032697 Instructions

● Thank you for purchasing our product. Before installing, please read the instruction carefully and keep it for future reference.
Attention!
●
For installation, follow the steps on the instruction sheet. Any damage caused by falty installation shall be imputed to the users.
● Don't break or modify the wires. To avoid a short circuit, do not pull the wires out of the terminals during installing.
● Do not disassemble, alter or change any parts.
●
Maintenance or repairs should be executed by our professionals.
◎ MARK MEANING:
You could get the installation details from the information behind the mark.
Some processes mus t be followed to avoid the affection caused by wrong installation .
Certain procedure must be followed to avoid damages to yourself or the public.
Certain procedure must be followed to avoid damages to the vehicle.
1 Accessories
1 2
Heated grip X2 Ring Fixed Switch X1
個
5
Bar-end cap X2
Contact your local distributor if the items received in the box are not the same as the one listed above.
2-1 Specifications
8.65 mm
57.9 mm
22.7 mm
Heated grip testing data
2-2
(℃)
120
100
80
60
40
20
0
0 5 10 15 20
HINWEIS Durchführung der Tsets bei einer Umgebung stemperatur von unter 26 °C miteiner Betriebsspannung von 13,5 V.
使用說明書
PRESS THE
BUTTON
M4x6xP0.7
3 4
Connecting wire X1
Hexagon Socket Screw X1
Design and specifications are subject to change without notice!
Level 5 Temperature Curve
Level 4 Temperature Curve
Level 3 Temperature Curve
Level 2 Temperature Curve
Level 1 Temperature Curve
25 30 (Minuten)
3-1 Practical installation instruction
Follow the steps below during installation.
Figure 1
FLASH LIGHT ON
Figure 2
PRESS THE
❶
BUTTON 3
ONCE SECONDS
❷
1.2 Nm (12 kgf.cm)
❶
Ring Fixed Switch (Accessory 2)
❷
M4 Hexagon Socket Screw (Accessory 4)
Figure 3
3-2 Wiring installation instructions
Ring Fixed Switch (Accessory 2)
EN Caution! Risk of burns! The heated grips can reach very high temperatures. The heated grips may only be used with suitable
hand protection.
DE ACHTUNG! Verbrennungsgefahr. Die Heizgriffe können sehr hohe Temperaturen erreichen.
Die Heizgriffe dürfen nur mit geeignetem Schutz für die Hände verwendet werden.
ES Atención! Riesgo de quemaduras. Los puños calefactables pueden alcanzar temperaturas muy elevadas.
Los puños calefactables deben utilizarse únicamente en combinación con una protección adecuada para las manos.
Risque de brûlure! Les poignées chauffantes peuvent atteindre des températures très élevées.
FR Attention!
Les poignées chauffantes doivent uniquement être utilisées avec une protection adaptée pour les mains.
Rischio di ustioni! Le manopole riscaldate possono raggiungere temperature molto elevate.
IT Attenzione!
È consentito utilizzare le manopole riscaldate solo con una protezione per le mani adatta.
NL Pas op! Gevaar voor brandwonden! De verwarmde handvaten kunnen zeer hoge temperaturen bereiken.
De verwarmde handvaten mogen alleen met een geschikte handbescherming worden gebruikt.
1. Use an appropriate tool to
Figure 4
remove the original handle-bar
grips.
2. Apply a cleaning agent and
wipe back and forth to remove
the glue residue from the
handlebar.
3. Please use an appropriate
Figure 5
tool to affix the ring fixed switch
Need to keep a small distance
(Accessory 2) to the handle.
Please adjust the angle during the
installation to prevent interfering
the button.
4. Push the heated grip
Figure 6
(Accessory 1) straight onto
the handlebar.
If the heated grip is not
fastened firmly enough to
the handlebars, apply a
little heated grip adhesive
(sold separately) to
prevent it from twisting
whilst on the road.
Black / Ground wire connects to the engine or
to the negative pole of the battery.
Red / Positive wire connecting
to the key on switch (DC 12 V)
Connecting wire (Accessory 3)
To install, do not use any tool to
knock the grip on direct. Do not
twist the grip by hand or with a
tool.By doing so, this will break
or damage the wire inside the
handlebar.
To install the heating grip
(Accessory 1) onto the throttle
sleeve, the throttle must
maintain a small distance with
a surplus distance for wiring;
You must test them by rotating
back and forth to make sure
they can twist.
5. To install the side cap
1. (Accessory 5) onto the
heating grip, insert the top
cap into the top groove and
then press it downward into
the bottom groove.
2.
Heated grip (Accessory 1)
wh04ax008c