Table of Contents
Advertisement
Quick Links
User Manual
BUS Enabled Motorized Curtain
HDL-MWM70B.12
HDL-MWM70S.12
www.hdlautomation.com
● Valid also for version 12.22
● Functions are the same for wireless version
MWM70-RF.12.
● Version MWM70S.12 does not exist anymore.
● Manual describes the snapshots taken in the
previous version of the module and using older
HBST program. In HBST2, the graphic
appearance is slightly different but the functions
remain the same
Advertisement
Table of Contents
Summary of Contents for HDL Buspro HDL-MWM70B.12
- Page 1 ● Manual describes the snapshots taken in the previous version of the module and using older User Manual HBST program. In HBST2, the graphic appearance is slightly different but the functions remain the same BUS Enabled Motorized Curtain HDL-MWM70B.12 HDL-MWM70S.12 www.hdlautomation.com...
- Page 2 User Manual HDL-MWM70B.12/MWM70S.12 Document updates: Version Date Description V1.0 2015.05.06 Finish new document Curtain Motors – User Manual...
-
Page 3: Table Of Contents
3.1 Characteristic........................3 3.2 Notice...........................4 3.3 Connecting..........................4 3.4 Curtain Rail Accessories....................5 3.5 The dimensions of ceiling bracket.................. 6 3.6 Installation steps........................6 3.7 HDL BUS Pro Description....................9 Curved Rail..........................9 LED Indication........................10 Software Configuration......................10 Workflow........................10 Modify address of motor................... 10 Confirm motor running mode................... -
Page 4: Overview
1.1.1 Description HDL-MWM70B.12, HDL-MWM70S.12 the motorized curtain contains master and slave. It is a professional curtain controller, the master is enabled by HDL Buspro. Support manual mode, it has the function of over load protection and over heat protection. 1.1.2 Serial Numbers MWM70B.12... -
Page 5: Device Description
User Manual HDL-MWM70B.12/MWM70S.12 1.3 Device Description a. latch ○ a b. Master: HDL Buspro interface Slave: invalid c. AC230V Power cable, 1 meter ○ b (Brown for L, Blue for N, Y/G for PE) d. RJ11 6P6C network port, connect to the master and slave. -
Page 6: Curtain Rail Installation
Slave interface 6P network port Rated power Rated torque 1.0Nm Rated speed 112rpm Rail belt speed 16cm/s Communication HDL Buspro (Master) Environmental Condition： Working temperature 0℃~45℃ Working relative humidity Up to 90% Storage temperature -20℃~+60℃ Storage relative humidity Up to 93%... -
Page 7: Notice
Built-in a new generation of clutch, system operating noise no more than 40dB The curtain’s horizontal pull reaches 8KG Use HDL-BUS port as interface, DLP panel to control the curtain, easy to use 3.2 Notice Read all instructions in detail before use ... -
Page 8: Curtain Rail Accessories
Master, Slave: The Master is connected to the Buspro port and AC220V, and it provides DC12V to the Slave by the RJ11 6P6C. HDL provides the 1 meter RJ11 cable. Ceiling Bracket’s mounting distance： On the top of rail, recommend every 600 mm installing a Ceiling Bracket. -
Page 9: The Dimensions Of Ceiling Bracket
User Manual HDL-MWM70B.12/MWM70S.12 3.5 The dimensions of ceiling bracket 3.6 Installation steps The length of the rail and the belt need to customize according to the size of the window. Turn to the reverse side of the rail, put the Track Joiner to the rail. - Page 10 User Manual HDL-MWM70B.12/MWM70S.12 left part Fixeture1 Clamp2 Clamp3 Adjust the Belt’s positions according to the figure, put the Carrier1 onto the Clamp2、 3, its handle should point to the Fixture1. Fixture1 carrier1 left part Clamp3 Clamp2 Thread the other side of the belt into the right path rail, drag it to the Drive unit, then pull it out.
- Page 11 RJ11 6P6C, HDL provides the RJ11 cable is 1 meter. If this 1 meter of RJ11 cable is not suit for you project, you can make the other RJ11 cable, about the Clamping Tool of RJ11, please see this: http://www.alibaba.com/product-detail/Round-LAN-Wire-Stripper-6P6C-RJ11_60076...
-
Page 12: Hdl Bus Pro Description
HDL-MWM70B.12/MWM70S.12 Motor 3.7 HDL BUS Pro Description Connector Information buspro DC24V Black DATA- White DATA+ Yellow 4. Curved Rail HDL provides the curved rail. But has some limits. θ <=90°and R>=300mm curtain rail is available. Curtain Motors – User Manual... -
Page 13: Led Indication
Note: the Step c), d), e) are set by HDL Easy Engineering Editor software. 6.2 Modify address of motor Long press the button 3s, the LED will turn ON, then you can modify the address by HDL Easy Engineering Editor software. Press the button 3s again or has no action after 2min, it... -
Page 14: Confirm Motor Running Mode
① 6.3 Confirm motor running mode Motor running mode：Forward or Reverse Confirm motor running mode by HDL Easy Engineering Editor software. Input motor’s Subnet ID and Device ID Download the information of Curtain, the default running mode is FWD. C. Select OPEN，... -
Page 15: Testing For Installation (Very Important)
User Manual HDL-MWM70B.12/MWM70S.12 ② ⑤ ① ③ ④ 6.4 Testing for Installation (very important) Long press the PROG button 5s, the LED will turn OFF 1 time per 2s, the curtain enters the installation mode. It will measure movable distance for the rail automatically;... -
Page 16: Set Position Of Open And Close
User Manual HDL-MWM70B.12/MWM70S.12 Automatic detection (see Section 6.4) User setting (see Section 6.5) Installation mode length User run-time length 6.5 Set position of open and close 6.5.1 Position open setting ① ② ③ a) Select Drag NO Action mode, then manually drag the curtain to the limit position of curtain-open which is the end-user wants. -
Page 17: Position Close Setting
User Manual HDL-MWM70B.12/MWM70S.12 6.5.2 Position close setting Select “Drag NO Action” mode, Save and Upload, then manually drag the curtain fabric to the limit position of curtain-close which is the end-user wants. Select Close, then click OK, now the limit position of Close is saved, it is a new different position from the detected limit position in Section 6.4. -
Page 18: Set Curtain's Action After Power On
User Manual HDL-MWM70B.12/MWM70S.12 Manual mode：long drag，short drag，drag no action. Long drag：Drag the certain fabric for certain distance (longer than the setting Length) and let go, the curtain will fully open or close automatically according to the direction you drag, the default Long drag Length is 20cm. -
Page 19: Panel Setting
HDL-MWM70B.12/MWM70S.12 6.8 Panel Setting The curtain can be controlled by 2 different kinds of commands. 1：The button’s setting as following. (HDL-BUS software) Operation: Long press the button, open or close the curtain, when loosen the button, it will stop running (If the curtain reaches the fully open or close position, and you have not loosen the button, it will stop automatically for protection.) -
Page 20: Easy Programming Mode
How does the Master Motor control the Slave Motor? The Master is connected to the HDL Buspro port and AC220V, and it provides DC12V to the Slave motor by the RJ11 6p6c. When the Master is forwarding or reversing, will control the Slave via the RJ11 line at the same time. - Page 21 User Manual HDL-MWM70B.12/MWM70S.12 7.3 CurtainFAQ003_Buspro Why and when we need the Slave Motor? When the curtain fabric is heavy, you may need to use Slave Motor, see the below curve. Curtain Motors – User Manual...
-
Page 22: Notes
User Manual HDL-MWM70B.12/MWM70S.12 8. NOTES Curtain Motors – User Manual...