Intense Sniper T User Manual
  1. Manuals
  2. Brands
  3. Intense Manuals
  4. Bicycle
  5. Sniper T
  6. User manual

Intense Sniper T User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

user manual //
s n i p e r T

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Sniper T and is the answer not in the manual?

Questions and answers

Related Manuals for Intense Sniper T

Summary of Contents for Intense Sniper T

  • Page 1 user manual // s n i p e r T...

  • Page 2: Introduction / Registration

    T // www.intensecycles.com/warranty-card/ The Sniper T is a dedicated pedaling machine with an uptick in rear wheel t e c h n i c a l a s s i s t a n c e travel for your favorite descent. We’ve reinforced the rear triangle for added techcenter@intensecycles.com...

  • Page 3: Table Of Contents

    // Introduction / Registration Getting to Know Your Sniper T Frame Features / Component Spec Geometry Exploded View and B.O.M. Assembly Frame Assembly Torque Specifications Setup Cable Routing Seatpost Setting the Sag Shock Setup Maintenance Carbon Care Maintenance Schedule I N T E N S E C Y C L E S .

  • Page 4: Getting To Know Your Sniper T

    C o m p o n e n t s p e c n o t e • Rear travel: 4.7 inches (120 ±±) • Internal cable routing The Sniper T is designed around the use of a single chain ring only. Use with 165 x 45 stroke shock • Internal seat tube cable routing of a double or triple ring set will not allow proper clearance with the frame.

  • Page 5: Geometry

    Geometry // g e o m e t r y n O T e Geometry taken at top out with 527.1 mm axle to crown length and 51 mm fork offset. BB Drop SMALL MEDIUM LARGE XLARGE Wheel Base: 1142 mm / 45” 1168 mm / 46”...

  • Page 6: Exploded View And B.o

    exploded view and b.o.m. // ITEM PART ITEM PART ITEM DESCRIPTION QTY. TORQUE SPEC. ITEM DESCRIPTION QTY. TORQUE SPEC. NUMBER NUMBER Bearing Cap Top Link Bearing Cap Cone Adjuster 130807 Blk, 8.3 mm Height 130765 24 mm OD (Lower) Top Link 130823 Carbon Top Link 7 Nm /...
  • Page 7 ITEM PART ITEM PART ITEM DESCRIPTION QTY. TORQUE SPEC. ITEM DESCRIPTION QTY. TORQUE SPEC. NUMBER NUMBER 11 Nm / SHCS, 14 Nm / Hanger Nut 130827 Hanger Nut (ST) SHCS M6 x 22 410009 100 in-lbs Socket Head, M6 x 22 125 in-lbs 16 Nm / Cone Adjuster Bolt, Socket...

  • Page 8: Assembly

    Preface // Service and maintenance on an INTENSE bicycle requires special tools, abilities and knowledge of working on bicycles. It is always recommended to use an authorized INTENSE dealer for service and maintenance. Always wear eye protection. It is critical to use the proper tools, loctite, grease and torque specs during assembly.

  • Page 9: Frame Assembly

    C O n n e C T i n G T O p L i n K T O F r O n T T r i A n G L e / / C O n n e C T i n G t h e l o w e r L i n K T O F r O n T T r i A n G L e // Holding top link (#130823) as Using upper pivot axle Holding the lower link (#130854),...
  • Page 10 C O n n e C T i n G r e A r T r i A n G L e T O l o w e r l i n k / / Put a small dab of grease on Insert greased main pivot bolt the outside bearing race as well (#130791) into non-drive side...
  • Page 11 C O n n e C T i n G C r O s s B r A C e T O r e A r T r i A n G L e / / C O n n e C T i n G r e A r T r i A n G L e T O T O p L i n K / / Lift the Sniper top link up and Gently spread the rear triangle Put a small dab of grease on...
  • Page 12 i n s T A L L i n G r e A r s H O C K / / Holding the shock with the Put a small dab of grease on Using a 6 mm hex bit on a torque Insert and thread in trunnion shaft and eyelet pointing towards the bearing spacer (#130832) and...
  • Page 13 i n s T A L L i n G C r O s s B r A C e T 2 5 T O r X H A r D W A r e // i n s T A L L i n G D e r A i L L e U r H A n G e r / / Holding the low profile screw #22 and #23).
  • Page 14 s H O C K T O r Q U e p r O C e D U r e / / T O p L i n K T O r Q U e p r O C e D U r e / / Using a 5 mm hex key and a 5 Using a 5 mm hex bit on a torque First step here is to tighten...
  • Page 15 L o w e r L i n K T O r Q U e p r O C e D U r e p T . 1 / / L o w e r L i n K T O r Q U e p r O C e D U r e p T . 2 / / Using a 8 mm hex bit on a Next install the cone spacer Using a 6 mm hex wrench and a 5 mm hex bit on a torque wrench,...
  • Page 16 r e a r A x l e A s s e m b l y / / Insert QR 148x12 mm rear axle Align and start the axle thread. Tip lever back over until parallel (#130846) into axle opening on (Image #37) then, grab the tips of with axle and push back in until non-drive side (Image #36).

  • Page 17: Torque Specifications

    Axle (non-drive side): 11 Nm / 100 in/lbs torque specifications // Achieving proper torque is vital to ensuring the safe performance and function of the Sniper T M8 HEX 7 Nm / 60 in/lbs M5 HEX 14 Nm / 125 in/lbs frame.

  • Page 18: Setup

    Sniper T are optimised for you. suspension compresses. 38 mm (1.5") T o o l s n e e d e d Feed the zip tie into the •...

  • Page 19: Seatpost

    seatpost // Before insertion, liberally coat the seat post with carbon paste and gently slide into the seat tube. With a minimum seat post insertion of 4", tighten seat post clamp to 5 Nm / 45 in-lbs. (Over tightening the seat post clamp will inhibit the movement of the seat post and potentially damage seat post and/or seat tube.

  • Page 20: Setting The Sag

    setting the sag // Release compression. Measure gap from 1. Remove fork and shock air caps and be sure you have a o-ring to seal lip. While suspension shock pump and a small ruler or measuring device handy. is compressed on fork or rear shock, 2.

  • Page 21: Shock Setup

    100 mm Travel shock setup // 40 mm Shock StRoke Shock Sag 30% when sitting on the bike 15-25% when sitting on the bike Fork Sag SHOCK: Float DPS Performance Elite Float DPS Factory SHOCK: RIDER WEIGHT(LBS/KGS) SPRING (PSI) Rebound (Clicks Out) FOX FlOaT dps 100 lbs/ 45 kgs 165 x 40 mm...

  • Page 22: Maintenance

    INTENSE Cycles dealer. Any direct impact to the frame can cause serious structural damage. • Use high grade waterproof grease on seat post, BB and head set bearing contact areas with the carbon.

  • Page 23: Maintenance Schedule

    maintenance schedule* // 500 Miles or 2000 Miles or 6 4000 Miles or Action Every Ride 1 Month Months 1 Year Check air pressure, inspect tread and sidewalls Tires for tears and punctures Brush off and lubricate Chain Squeeze brakes and confirm function Brakes General Clean complete bike of mud and debris...
  • Page 24 www.InTenseCYCles.com p h o n e : + 1 ( 9 5 1 ) - 3 0 7 - 9 2 1 1 C u s t o m e r s e r v i c e : t e c h c e n t e r @ i n T e n s e c y c l e s . c o m G e n e r a l i n f o : i n f o @ i n T e n s e c y c l e s .

Table of Contents