Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ekwb EK-Quantum Reaction AIO RX 6800/6900 D-RGB P240 - AMD Radeon Edition
Summary of Contents for ekwb EK-Quantum Reaction AIO RX 6800/6900 D-RGB P240 - AMD Radeon Edition
- Page 1 EK-Quantum Reaction AIO RX 6800/6900 D-RGB P240 - AMD Radeon Edition USER GUIDE...
- Page 2 To ensure safe and easy installation, please read this manual carefully before starting with the installation process! Safety Precautions Before you start using this product, please follow these basic guidelines: Check the component list and condition of the product before installation.
-
Page 3: Table Of Contents
TABLE OF CONTENTS BOX CONTENTS DIMENSIONS INSTALLING THE GPU WATER BLOCK AND BACKPLATE FAN SPLITTER HUB ELECTRICAL CONNECTIONS Option 1 CONNECTING THE HUB TO THE POWER SUPPLY CONNECTING THE HUB TO THE MOTHERBOARD ELECTRICAL CONNECTIONS Option 2 CONNECTING THE PUMP DIRECTLY TO THE MOTHERBOARD FAN HEADER AIO UNIT ORIENTATION LIMITATIONS INSTALLING THE AIO UNIT CONNECTING THE D-RGB LIGHTS... -
Page 4: Box Contents
BOX CONTENTS Self-Tapping Fan Mounting Screws EK D-RGB 6-Way Splitter Cable EK Cable Y-Splitter 2-Fan PWM All-In-One GPU Liquid Cooling Unit With the Mounting Mechanism and Connection Cables - 4 -... -
Page 5: Dimensions
DIMENSIONS 136 mm 70 mm 105 mm - 5 -... -
Page 6: Installing The Gpu Water Block And Backplate
INSTALLING THE GPU WATER BLOCK AND BACKPLATE To install the water block to your graphics card, follow the instructions in the link below: https://www.ekwb.com/shop/EK-IM/EK-IM-3831109833391.pdf FAN SPLITTER HUB All the elements that need electricity to run are connected to the fan To the Power Supply Unit splitter hub, located on the back of the unit. -
Page 7: Electrical Connections Option 1
ELECTRICAL CONNECTIONS Option 1 CONNECTING THE HUB TO THE POWER SUPPLY STEP 1 Take the enclosed power cable and plug the 2-pin PCI Express Mini- Fit power connector into the fan splitter hub. STEP 2 Use the SATA POWER connector and plug it into the female STEP 1 STEP 2 connector found on the main power supply. -
Page 8: Electrical Connections Option 2
ELECTRICAL CONNECTIONS Option 2 CONNECTING THE PUMP DIRECTLY TO THE MOTHERBOARD FAN HEADER If you want to control the speed of the pump and fans separately, you should follow these steps: STEP 1 Disconnect the pump cable from the fan splitter hub. You need to remove cable ties to do so. -
Page 9: Aio Unit Orientation Limitations
AIO UNIT ORIENTATION LIMITATIONS CAUTION: The unit’s orientation is critical since incorrect installation can lead to poor cooling performance and premature unit failure. Pump Pump Pump Pump Pump Pump - 9 -... -
Page 10: Installing The Aio Unit
INSTALLING THE AIO UNIT STEP 1 Mounting the AIO unit into your PC chassis requires special attention. You will need eight fan mounting screws and a Phillips head screwdriver. STEP 1 STEP 2 The AIO unit’s position depends on the size, fan mounting holes, and hardware you have installed inside your chassis. -
Page 11: Connecting The D-Rgb Lights
STEP 3 Once you have selected the mounting position within the case, you must align the fan mounting holes with the ones in the case. Use the enclosed self-tapping screws to install the unit firmly. Self-tapping screws require more torque than threaded screws but don’t overdo it with force applied. -
Page 12: Alternative
ALTERNATIVE You can use the enclosed 6-way D-RGB splitter cable to connect all the 6-Way D-RGB Male D-RGB cables into one header on your motherboard. Splitter Headers D-RGB Connectors - 12 -... -
Page 13: Support And Service
SUPPORT AND SERVICE In case you need assistance, please contact: https://www.ekwb.com/customer-support/ EKWB d.o.o. Pod lipami 18 1218 Komenda Slovenia - EU SOCIAL MEDIA EKWaterBlocks @EKWaterBlocks ekwaterblocks EKWBofficial ekwaterblocks...
Need help?
Do you have a question about the EK-Quantum Reaction AIO RX 6800/6900 D-RGB P240 - AMD Radeon Edition and is the answer not in the manual?
Questions and answers