Table of Contents
Advertisement
English
a)
Table saw (fig. 1)
- Set the switch [1-9] to the lower position.
- Swivel the handle [1-8] downwards and use it
to pull the saw unit forwards until it clicks into
place.
The saw unit is now in a central position on the
table and the machine can be used as a table saw.
b)
Circular trimming saw (fig. 3)
- Set the switch [3-10] to the upper position.
When the handle [3-9] is swivelled downwards, it
can move the saw unit backwards and forwards for
making cuts. The backwards motion is supported
by a spring force.
5.5
Dust extraction
The PRECISIO has two vacuum connec-
tions: A top guard with bayonet coupling
[2-3] with a diameter of 27 mm and
a bottom guard [2-2] with a diameter of
35 mm.
The CS 70 AB dust extraction set (included in the
delivery of CS 50 EB) connects the two vacuum
connections together so that a Festool mobile
dust extractor can be connected.
5.6
Power supply and operation
The mains voltage must correspond to
the specification on the rating plate.
- In North America, only Festool machines with
the voltage specifications 120 V/60 Hz may be
used.
- We recommend using a 16 A fuse because of the
performance of the motor.
- Before use always inspect the flexible lead and
the plug. Have the defects repaired by a special-
ist repair shop.
- Outside the premise use only approved exten-
sion leads and cable connections.
To switch the power tool on, press the ON/OFF
switch [4-1] and the locking switch [4-4] at the
same time. The machine will run as long as the
ON/OFF switch remains pressed.
For continuous operation once the power tool has
been switched on, release the ON/OFF switch
[4-1] first and then release the locking switch
[4-4]. To switch continuous operation off, either
press the ON/OFF switch again and then release
it, or press the red switch [4-6].
To prevent the device from being switched on
without authorisation, a U-lock can be fitted to
the ON/OFF switch hole [4-2].
5.7
Extra feet [1-11] [1-12]
Always use the extra feet with an extension table
(width or length) or sliding table. Loosen the screw
[1-11], swivel the leg [1-12] down until it has set-
tled on the floor and retighten the screw [1-11].
5.8
Installing the accessory holder (fig. 13)
When connecting the two individual parts, make
sure that the tabs on the latches fit together ex-
actly and lock in place. Also check the back of the
accessory holder to make sure the latches are in
the correct position in the holding brackets.
5.9
Cuts along the mitre
For cuts along the mitre, the preset profile setting
rail should be on the right-hand side of the table.
5.10
Switching on the machine when cutting
metal
When cutting metal, switch on the saw using a
residual current circuit breaker.
6
Electronics
The machine features full-wave electron-
ics with the following properties:
6.1
Smooth start-up
The electronically controlled smooth start-up
function ensures that the machine starts up
smoothly.
6.2
Speed control
The rotational speed is infinitely adjustable be-
tween 1600 and 4200 rpm using the adjusting
wheel [4-5]. This enables you to optimise the
cutting speed to suit the respective material [4-3].
#
n
[rpm]
0
1
~ 1600
2
~ 2100
3
~ 2600
The preselected motor speed is kept constant
through electronic control. This ensures a uniform
cutting speed even when under load.
6.3
Overload safety device
The power supply is restricted if the machine is
overloaded to extremes. The power supply is dis-
connected completely if the motor jams for some
time. You will need to remove the load and/or
switch off the machine before you can use it again.
6.4
Temperature cut-out
The power supply is restricted and the speed re-
duced if the motor exceeds a certain temperature.
The machine continues operating at reduced power
26
#
n
[rpm]
0
4
~ 3100
5
~ 3600
6
~ 4200
Advertisement
Table of Contents
