GREISINGER GMH 3710 Operating Manual

H49.0.01.6C-03
Operating Manual Precision Thermometer
For Pt100 4-Wire Temperature Probes
1 IN GENERAL............................................................................................................................................................................ 1
1.1 S I
AFETY NSTRUCTIONS
1.2 H O
OW TO PERATE
1.3 C ...................................................................................................................................................................... 2
ONNECTIONS
1.4 D E
ISPLAY LEMENTS
1.5 P ...................................................................................................................................................................... 2
USHBUTTONS
2 DEVICE CONFIGURATION.................................................................................................................................................. 3
2.1 'U ': S
NIT ELECTION OF
2.2 'R ': T
ESOLUTION
2.3 'O ': Z D
FFSET ERO
2.4 'S ': S C
CAL CALE
2.5 'P . ': S
OWER OFF ELECTION OF
2.6 'O ': F
UT UNCTION OF THE
2.7 'A ': S
DDRESS ELECTION OF
2.8 ' AC.0V ': O
D OLT
2.9 ' AC.0V ': O
D OLT
3 SOME BASICS OF PRECISION TEMPERATURE MEASURING................................................................................... 4
4 SPECIAL FUNCTIONS ........................................................................................................................................................... 5
4.1 D R
ISPLAY ESOLUTION
4.2 Z D
ERO ISPLACEMENT
4.3 S C
CALE ORRECTION
4.4 O ................................................................................................................................................................................ 5
UTPUT
4.4.1 Interface - Base Address ('Adr.') ................................................................................................................................. 5
4.4.2 Analogue Output - Scaling with DAC.0 and DAC.1................................................................................................... 6
5 FAULT AND SYSTEM MESSAGES...................................................................................................................................... 6
6 CALIBRATION SERVICES.................................................................................................................................................... 6
7 SPECIFICATION ..................................................................................................................................................................... 7

1 In General

1.1 Safety Instructions

This device has been designed and tested in accordance to the safety regulations for electronic devices.
However, its trouble-free operation and reliability cannot be guaranteed unless the standard safety measures and special safety advises given in
this manual will be adhered to when using it.
1. Trouble-free operation and reliability of the device can only be guaranteed if it is not subjected to any other climatic conditions than those
stated under "Specification".
2. If the device is transported from a cold to a warm environment condensation may result in a failure of the function. In such a case make sure
the device temperature has adjusted to the ambient temperature before trying a new start-up.
3. If device is to be connected to other devices the circuitry has to be designed most carefully. Internal connection in third party devices (e.g.
connection GND and earth) may result in not-permissible voltages impairing or destroying the device or another device connected.
4. Warning: If device is operated with a defective mains power supply (e.g. short circuit from mains voltage to output voltage) this may result in
hazardous voltages at the device (e.g. at sensor socket)
5. If there is a risk whatsoever involved in running it, the device has to be switched off immediately and to be marked accordingly to avoid re-
starting. Operator safety may be a risk if:
• there is visible damage to the device
• the device is not working as specified
• the device has been stored under unsuitable conditions for a longer time
In case of doubt, please return device to manufacturer for repair or maintenance.
6. Warning: Do not use these product as safety or emergency stop device, or in any other application where failure of the product could result in
personal injury or material damage.
Failure to comply with these instructions could result in death or serious injury and material damage.
GMH 3710
......................................................................................................................................................... 1
A M D
ND AINTAIN EVICE
............................................................................................................................................................. 2
T U
EMPERATURE NIT
D R ........................................................................................................................... 3
HE ISPLAY ESOLUTION
........................................................................................................................................... 3
ISPLACEMENT
................................................................................................................................................. 3
ORRECTION
P -O D
OWER FF
O ........................................................................................................................................ 3
UTPUT
B A
ASE DDRESS WHEN
O W O
UTPUT FFSET HEN UTPUT
S W O
UTPUT CALE HEN UTPUT
.......................................................................................................................................................... 5
('O ').......................................................................................................................................... 5
FFSET
('S ').............................................................................................................................................. 5
CALE
from Version 1.0
.......................................................................................................................... 2
°C /°F............................................................................................................... 3
................................................................................................................. 3
ELAY
O = S I
UTPUT ERIAL NTERFACE
= A O
NALOGUE UTPUT
= A O
NALOGUE UTPUT
................................................................. 3
............................................................................... 3
................................................................................. 3