Fcc Information; Battery Notes - Makeblock mBot Manual

FC mBot

FCC Information

This device complieswith part 15 of the FCC Rules. Operation is subject tothe
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to complywith the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guaranteethat
interference will not occur in a particular installation. lf this equipment does cause
harmful interference to radio or television reception, which can be determined by
turningthe equipment off and on, the user is encouraged to tryto correctthe
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
-- lncrease the separation between the equipmentand receiver.
-- Connect the equipment into an outleton a circuitdifferentfrom thatto which the
receiver is connected.
-- Consultthe dealeror an experienced radio/TVtechnician for help.
This modular complies with FCC RF radiation exposure limitssetforth for an
uncontrolled environment. This transmitter must not be co-located or operating in
conjunction with any otherantenna or transmitter.
lf the FCC identification number is not visible when the module is installed inside
anotherdevice, then the outside ofthe device into which the module is installed must
also display a labet referring to the enclosed module. This exterior labet can use
wordingsuch as the following: "ContainsTransmitter Module FCC ID:
2ACWW1300133B Or Contains
FCC ID: 2ACWW1300133B Or Contains FCC ID: 2ACWW1300303M Or Contains
FCC 1D: 2ACWW1300303U"
when the module is installed inside anotherdevice, the user manual of this device
mustcontain belowwarning statements;
1. This device complies with Part 15 ofthe FCC Rules. Operation is subject to the
following two
conditions:
(1) This device may notcause harmful interference.
(2) This device mustaccept any interference received, including interference that may
cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authorityto operatethe equipment.
The devices must be installed and used in strict accordance with the manufacturer's
instructions as described in the user documentation that comes with the product.
Product mBot
Warnings
· Adult supervision and assistance are required.
· CHOKING HAZARD- This product contains small parts and functional sharp
FC
points an components. Keep awayfrom children under age 3.
- Read and follow all instructions in the user' s guide before use.
· Retain this user' s guide for future reference.

Battery Notes

· Use onlyfresh batteries of the required size and type. Do not mix old and
new batteries, different types of batteries (Standard, alkaline, or
rechargeable), or rechargeable batteries of different capacities.
· Dispose of batteries promptly and properly. Da not burn or burythem.
· lf you do not plan to playwith the robot for an extended period of time,
remove the batteries.
Caution
· Da not insertthe wires into telecommunication or network socket outlets.
· As an extra precaution, check this product regularlyfor signs of wear or
damage.
· Ensure all wiring connections are correct before inserting batteries and
switching on the product. Failure to do so may result in damage to
components and the product.
· Ensure all wires are correctly connected to the batteryterminals and other
connectors. lf the circuit does not work, make sure the plastic insulation of
the wire is not obstructing the connection to the connector.
- When you have finished playing, remove the batteries and switch offthe unit
before you disconnect the wires. Do not apply any components or parts to
the unit other than those provided with this kit.
· To preventoverheating and damage, do not short-circuit the batteryterminals
and connectors. Do not block or cover the motor or other moving parts.
This equipment complies with FCC RF radiation exposure limits set
forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum
distance of 20 centimeters between the radiator and your body.
You may contact the warrantor at: support@makeblock.com