1. Manuals
  2. Brands
  3. Huvema Manuals
  4. Saw
  5. HU 355 DRYCUTTER-2
  6. Manual

Huvema HU 355 DRYCUTTER-2 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
C U T - O F F
S A W
HU 355 DRYCUTTER-2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HU 355 DRYCUTTER-2 and is the answer not in the manual?

Questions and answers

Related Manuals for Huvema HU 355 DRYCUTTER-2

Summary of Contents for Huvema HU 355 DRYCUTTER-2

  • Page 1 C U T - O F F S A W HU 355 DRYCUTTER-2...

  • Page 2: Table Of Contents

    able of conTenTs General safety rules for all machines Additional safety rules Specifications Unpacking and checking contents Getting to know your saw 4.1 Depth stop adjustment 4.2 Changing the blade 4.3 Adjusting the stationary vise and the cutting angle 4.4 Big blade guard and small blade guard 4.5 Cleaning the chip tray Basic saw operations Maintenance and lubrication...

  • Page 3: General Safety Rules For All Machines

    Hu 355 off saw drycuTTer 1. G eneral safeTy rules for all macHines N.B.: Read the instructions carefully in order to avoid any problems. As with all machinery there are certain hazards involved with operation and use of this machine. Using the machine with respect and caution will considerably lessen the possibility op personal injury.

  • Page 4: Additional Safety Rules

    ddiTional safeTy rules Always keep in mind that: • The machine must be switched off and disconnected from the power supply during maintenance and repairs, • Clamped workpieces may only be measured when the machine is switched off. Never lean over the machine, mind loose clothing, ties, jewellery etc. And wear a cap. Do not remove safety devices or guards.

  • Page 5: Getting To Know Your Saw

    4. G eTTinG To know your saw Figure 1 Figure 2 Figure 3 Figure 4 1. Warning label 2. Chain: for easy carrying and storage, the cut-off saw can be clamped in the down position by means of the hold down chain.

  • Page 6: Depth Stop Adjustment

    4.1 d epTH sTop adjusTmenT Figure 5 Figure 6 The depth stop should be adjusted so that the maximum cutting capacity is maintained and so that the blade does not hit the saw base or the surface on which the tool is mounted. •...

  • Page 7: Adjusting The Stationary Vise And The Cutting Angle

    • Install new blade (G) making certain teeth of saw blade are pointing down at the front and re- assemble outside blade flange (F), washer (E) and arbor screw (D). Turn arbor (D) clockwise to tighten. • Replace saw blade cover that was remove in step 2. MAKE SURE ARBOR LOCK (C) IS DISENGAGED AND 8 MM HEX WRENCH IS REMOVED BEFORE TURNING ON THE POWER.

  • Page 8: Basic Saw Operations

    5. b asic saw operaTions General cutting instructions • Let the blade reach full speed before cutting. • Don’t force the tool. It will do the job better and safer at its designed rate. Feed the saw into the workspace only fast enough to let the blade cut without bogging down or binding.

  • Page 9: Maintenance And Lubrication

    6. m ainTenance and lubricaTion DISCONNECT THE MACHINE FROM THE POWER SOURCE BEFORE CARRYING OUT ANY MAINTENANCE • Keep the tool clean. Remove accumulated chips from working parts. • Make sure that the tool operates properly, periodically check screws and bolts for tightness. •...

  • Page 10: Parts Drawing

    8. p arTs drawinG Figure 15 CHANGES AND T YPING ERRORS RESER VED...
  • Page 11 All rights reserved. No part of this booklet may be reproduced in any form, by print, photoprint, microfilm or any other means without written permission from the publisher. © Huvema BV, Kennedylaan 14, Veghel, the Netherlands. Internet: www.huvema.nl CHANGES AND T YPING ERRORS RESER VED...

Table of Contents