Before Starting The Equipment - Scheppach MGT410 Translation Of Original Operating Manual

Lithium-ion battery
Voltage
Capacity
Charging time
Charging unit
Input voltage
Power rating
Output voltage
Output current
Protection Class
Sound and vibration
Sound and vibration values were measured in ac-
cordance with ISO 22868.
Hedge Trimmer
L sound pres-
76.6 dB(A)
pA
sure level
K uncertainty 3 dB(A
WA
L sound power
86.5 dB(A)
WA
level measured
K uncertainty 3 dB(A
WA
L sound power
92 dB(A)
WA
level guaranteed
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with ISO 22867.
Hedge Trimmer
Vibration emission
2.87 m/s
value a
h
K uncertainty
The specified vibration value was established in ac-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specified value in excep-
tional circumstances.
The specified vibration value can be used to com-
pare the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect work-
ing order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
24 GB
18 V
1500 mAh
75 min
100-240 V / 50-60 Hz
40 W
21 V
1.5 A (h)
II
Pole Saw
68.9 dB(A)
3 dB(A)
88.9 dB(A)
3 dB(A)
93 dB(A)
Pole Saw
1.635 m/s
2 2
1.5 m/s 1.5 m/s
2 2

Before starting the equipment

Caution! Do not fi t the battery until the equipment
has been fully assembled and all the settings have
been actuated. Always wear protective gloves when
working on the equipment to protect yourself against
injury. Carefully unpack all parts and check that they
are complete.
Assembly
Fitting the chain saw mounting kit (for use as a pole-
operated pruner)
Assembly of the cutter rail and the saw chain
• Undo the fixing screw (17) of the chain wheel cover
(Fig. 2).
• Take off the chain wheel cover (18). (Fig. 3)
• Lay the chain as shown in the groove which runs
around the cutter rail (Fig. 4/Item 19).
• Insert the cutter rail and chain as shown in the
mounting in the chainsaw (Fig. 5).
• At the same time guide the chain around the chain
wheel (Fig. 5/Item 20).
• Attach the chain wheel cover (Fig. 6/Item 18) and
fasten it hand-tight with the fastening screw.
• Do not fully tighten the fastening screw until after
you have adjusted the chain tension.
Tensioning the saw chain
Caution! Always remove the battery from the device
before inspection and adjustment. Always wear pro-
tective gloves when working on the chainsaw to pro-
tect yourself against injury.
• Undo the fixing screw (18) of the chain wheel cover
a few turns (Fig. 6).
• Adjust the chain tension with the chain tensioning
screw (Fig. 7/Item 21). Turning the screw clockwise
increases the chain tension, turning it counter-
clockwise decreases the chain tension. The saw
chain is correctly tensioned if it can be lifted ap-
prox. 2 mm in the middle of the cutter rail (Fig. 8).
• Secure the fixing screw (18) of the chain wheel
cover (Fig. 6).
Notice! All the chain links must lie properly in the
guide groove of the cutter bar.
Notes on tensioning the chain:
The saw chain must be properly tensioned to ensure
safe operation. You can tell that the chain tension is
perfect if the saw chain can be lifted by around 2 mm
in the middle of the cutter rail. As the saw chain heats
up during cutting and thus changes in length, check
the chain tension no less than every 10 minutes and
adjust it again as required. This applies in particular
to new saw chains. When you have fi nished work-
ing slacken the chain again, as the chain will shorten
when it cools down. This will prevent the chain from
being damaged.