Related Manuals for Maytronics CLASSIC 8+
Summary of Contents for Maytronics CLASSIC 8+
- Page 1 CLASSIC 8+ / TOP 8 Maytronics Dolphin robotic pool cleaner User Instructions 8180035...
-
Page 2: Table Of Contents
CLASSIC 8+ / TOP 8 Robotic Pool Cleaner User Instructions Contents 1. INTRODUCTION ..............................2 2. SPECIFICATIONS ..............................2 3. WARNINGS AND CAUTIONS ..........................2 4. ROBOTIC POOL CLEANER PARTS ........................4 5. USE THE POOL CLEANER ............................5 5.1 Setup ..................................5 5.2 Adjust the Handle Angle ...........................5 5.3 Place the Pool Cleaner in the Pool ...................... -
Page 3: Introduction
1. INTRODUCTION Thank you for purchasing a Maytronics Robotic Pool Cleaner. We are sure that your Maytronics Robotic Pool Cleaner will provide you with reliable, convenient and cost-effective pool cleaning. Its reliable filtration in all pool conditions, active brushing, and all-surface climbing brush enhance maximum pool hygiene. - Page 4 Keep the Robot Pool Cleaner out of the reach of children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction. WARNING The unit must be connected only to a supply circuit that is protected by a ground-fault circuit interrupter (GFCI).
-
Page 5: Robotic Pool Cleaner Parts
5. USE THE POOL CLEANER Robotic Pool Cleaner Remote Control Unit - Optional Brushes Combined Brush Wonder Brush All surface climbing brush, For smooth ceramics. ideal for most pool surfaces. Filtration Cartridge with net filters (X4) Ultra fine net filter (X4) (optional) Power supply... -
Page 6: Use The Pool Cleaner
5.1 Setup The Pool Cleaner is very simple to use. Simply place it in the pool and make sure that it is correctly positioned on the floor of the pool. Turn it ON and enable it to complete the task. Before using the Pool Cleaner for the first time, perform the following steps: Unwind the blue cable and stretch it out completely so that it has no kinks. -
Page 7: Place The Pool Cleaner In The Pool
Position the power supply so that it is approximately at the center of the long side of the pool at 5.2.1 min 3.5m/12ft from the pool and placed min 11cm/4'' above the ground. Attach the blue cable to the power supply by inserting it with the notch on the connector (1) lined 5.2.2 up with the groove in the socket on the power supply and turning clockwise (2). -
Page 8: Use The Mydolphin™ Plus Iot Mobile App
6. USE THE MyDolphin™ Plus IOT MOBILE APP Please download the Maytronics MyDolphin™ Plus app to your mobile smart device from either Google Play for Android or the Appstore for iOS. The Maytronics MyDolphin™ Plus app is cloud-connected, enabling control from anywhere at anytime, with real-time connectivity. -
Page 9: Led Lighs
6.4 LED Lights Connectivity LEDs The connectivity LED light on the power supply has several modes: 1. Flashing blue light - waiting for Bluetooth® connection. 2. Steady blue light - connected via Bluetooth®. 3. Flashing green light - power supply is trying to connect to your home/pool Wi-Fi® network and cloud, or a weak internet signal. -
Page 10: How To Use The Remote Control
7. HOW TO USE THE REMOTE CONTROL * for specific models only STATUS BAR CLEANING SETTINGS ACTION MODE SELECTOR ON / OFF STATUS BAR Signal strength Battery level indicator indicator Manual drive mode Filter indicator * Technician mode * Blinks when you need to clean the filter CLEANING SETTINGS ACTION CLEANING... -
Page 11: Automatic Mode
7.2 Automatic Mode The remote-control-unit offers two automatic operation modes: • Delayed Operation • Weekly Scheduling In Delayed Operation mode, you can set the Pool Cleaner to clean the pool later, by pressing START LATER. The power supply will start blinking green. After one hour, the Pool Cleaner will start working. -
Page 12: Removing The Pool Cleaner From The Water
7.4 Removing the Pool Cleaner from the water Turn OFF the power supply. WARNING 7.4.1 Using the blue cable, bring the Pool Cleaner to the pool edge. 7.4.2 Use the handle to remove the Pool Cleaner from the water. 7.4.3 Place the Pool Cleaner on the edge of the pool to let the water drain out. -
Page 13: Routine Maintenance
9. ROUTINE MAINTENANCE Clean the Cartridges Filters Unplug the power supply before any servicing activity. WARNING Note: Do not let the cartridges filters dry out before cleaning. 9.1.2 9.1.1 Open the clips and remove Open the filter covers and the filters. remove the cartridges from both sides of the robot. - Page 14 Reassemble the filter elements: Insert the locating tabs at the bottom of the filter element into 9.1.4 their grooves on the base frame. Clean the filter basket with a hose. “S” clip Locating tab Locating tab groove 9.1.5 Grooved Octagonal fitting fitting Do not force the filters into place.
-
Page 15: Troubleshooting
10. TROUBLESHOOTING Unplug the power supply before performing any action. WARNING Symptom Possible reason Corrective action Power-supply • No voltage in the power socket in the wall. • Check that there is voltage in the power socket in the wall. or switch is not •... -
Page 16: Mydolphin™ Plus - Troubleshooting
11. MyDolphin™ Plus - TROUBLESHOOTING Before using the app, make sure you have: • Cellular connection 3G/4G/5G or Wi-Fi®, with strong signal strength • Power supply support 2.4Ghz ONLY • Bluetooth® enabled Action What To Do Pool cleaner does not connect to Wi-Fi®, and power supply is trying to connect to your home/pool Wi-Fi®... - Page 17 → The MU will link to robot and the app → home screen. If you do not recognize the serial number, press to add the robot s/n manually or scan the QR Code. If these solutions do not solve your problem, contact Maytronics Customer Care: North America 1-888-365-7446 ext. 1002 customersupport@maytronicsus.com...