Advertisement
Installation WiFi system: minimum requirements Wi-Fi router
Wi-Fi Router Minimum Requirements
•
Compatible with IEEE 802.11 n/g/b
• Compatible with IEEE 802.11n/g/b
•
WPA2 encryption
• W PA2 encryption
•
Radio frequency: 2,4 GHz band
•
Wireless auto channel: automated search for wireless LAN radio channel free
• Radio frequency: 2,4GHz band
of interference
• Wireless auto channel: auto search for wireless L A N radio
•
Support for the User Datagram Protocol(UDP) especially on company
channel free of interference
networks.
• Support for the User Datagram Protocol (UDP) especially
•
3 antenna systems for proper reception
on company networks
Minimum requirements Smart Device:
• 3 antenna systems for suitable
•
IOS 8.0 or Android 4.4
reception
Notices:
Smart Device Minimum Requirements
•
Receiver and remote control are having bi-directional communication. Status
info every 10 sec during first 2 min- afterward every 4 to 6 min up to 1h.
• IOS 8.0 or Android 4.4
Immediate sync when using remote.
Notices
•
Multiple users on same channel may interfere with data transfer. Press reset
button on myfire Wi-Fi box for 1 sec to change current channel.
• Receiver and remote control use bi-directional
•
If Wi-Fi box is not connected to receiver or is not used it will leave the Access
communication. Status info every 10 seconds during first 2 minutes
Point(AP) mode after 24 hours.
•
Multiple fireplaces using Wi-Fi boxes, minimum distance 60cm to avoid
- afterwards every 4 to 6 minutes, up to 1 hour. Sync is immediate
interference.
when using the remote.
•
Wi-Fi box allows communication via Home Network by wireless signal. Using
• Multiple users on same channel may interfere with data transfer.
remote control to achieve full functionality such as roomtemp measurement.
Press reset button on myfire Wi-Fi box for 1 second to change
•
When receiver/wi-fi box overheat(60 degreeC max) fires runs to pilot position.
channel.
• If myfire Wi-Fi box is not connected to receiver or is not used it will leave Access
Point mode after 24 hours.
• Multiple fireplaces using Wi-Fi boxes, minimum distance required is 60cm, to
avoid interference.
• Wi-Fi box allows communication via home network by using wireless signal.
• Remote control allows full functionality such as room temperature measurement.
Remote & receiver synchronization:
• W hen receiver/ Wi-Fi box overheats (60ºc M A X) fires run to pilot position.
Remote and Reciever Syncronisation
•
Complete installation of the system before starting sync.
Remote & receiver synchronization:
•
Insert batteries in remote and connect AC mains power to receiver.
• Complete installation of the system is required before sync.
•
ON/OFF switch on gasvalve to ON position
• Insert batteries in remote and connect AC mains power to receiver.
•
Receiver has to learn handset code(random selection of 65k unique codes available):
•
Complete installation of the system before starting sync.
• ON/OFF switch on gas valve to ON position
•
Press and hold receiver's reset button untill you year 2 beeps. After the second
•
Insert batteries in remote and connect AC mains power to receiver.
longer beep release reset button
•
ON/OFF switch on gasvalve to ON position
• Receiver has to learn handset code (random selection of 65k unique codes available)
•
Within 20 sec press the low flame button on remote, 2 short confirmation beeps can
•
Receiver has to learn handset code(random selection of 65k unique codes available):
• Press and hold receivers reset button until you hear 2 beeps. After the second longer
be heard. "CONN" is displayed on the remote. After succesfull sync the current state
•
Press and hold receiver's reset button untill you year 2 beeps. After the second
beep, release the rest button.
of the gasfire is displayed on the remote control.
longer beep release reset button
• Within 20 seconds pressthe low f lame button on remote, 2 short confirmation beeps
•
Within 20 sec press the low flame button on remote, 2 short confirmation beeps can
can be heard. "CONN" is displayed on the remote. After successful sync the current
be heard. "CONN" is displayed on the remote. After succesfull sync the current state
of the gasfire is displayed on the remote control.
state of the gas fire is displayed on the remote control.
INSTALLATION
Remote & receiver synchronization:
•
Complete installation of the system befo
•
Insert batteries in remote and connect A
•
ON/OFF switch on gasvalve to ON posi
•
Receiver has to learn handset code(ran
•
Press and hold receiver's reset bu
longer beep release reset button
•
Within 20 sec press the low flame
be heard. "CONN" is displayed on
of the gasfire is displayed on the r
Advertisement
