Delta DVP-EH2 Series Instruction Sheet

http://www.delta.com.tw/industrialautomation/
High-Speed, Multi-Functional
Programmable Logic Controller
Instruction Sheet
Warning
This instruction sheet only provides introductory information on electrical specification, functions, wiring,
trouble-shooting and peripherals. For detailed information on programming and instructions, please refer to
"DVP-PLC Application Manual: Programming". For how to purchase its peripheral devices, please refers to the
manual enclosed with the product.
DVP-EH2 is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne dust, humidity,
electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g. key
or specific tools are required for opening the enclosure) in case danger and damage on the device may occur.
DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur. Check all
the wiring again before switching on the power and Do NOT tough any terminal when the power is switched on.
Make sure the groud terminal is correctly grounded in order to prevent electromagnetic interference.

Introduction

1.1 Model Explanation & Peripherals
Nameplate Explanation Model/Serial No. Explanation
32EH00R2 0 T 6 16 0018
Delta PLC model name DVP32EH00R2
MODEL
Power input specification
POWER INPUT 100~240VAC 50/60Hz 30VA MAX
Output module specification OUTPUTMODULE 2.0A 250Vac 50/60Hz RES LOAD
Barcode & series No.
32EH00R2T6160018
Firmware version
VX.XX
MADE IN XXXXXX
DELTA ELECTRONICS,INC.
1.2 Product Profile & Outline
3 4 5
2
1
6
7
8
5 9
9 4
Communication port cover Extension module connection port cover
I/O terminal cover Input indicator
Function card/memory card cover Output indicator
I/O terminals DIN rail clip
I/O terminal No. DIN rail (35mm)
6
2
1
7
8
1
3
2
5
4
Mounting screw Memory card port
Direct mounting hole POWER/RUN/BAT.LOW/ERROR indicator
Battery socket Extension module connection port
Function card mounting hole
2006-10-24
Removable Terminal Block
COM 2 (RS-485)
RUN / STOP SWITCH
VR 0
5011650900-H2E0
COM 1 (RS-232)
Battery
1.3 Installation of function card/memory card (optional accessories)
Remove function card
For details, see the instruction sheets of these accessories.

Electrical Specifications

Model
Item
Power supply
voltage
Fuse capacity
Power
consumption
DC24V current
supply
Power protection
Withstand voltage
Insulation
Production No.
resistance
Production week
Production year (2006)
Noise immunity
Production plant (Taoyuan)
Version No.
Earth
Model name
Operation/storage
Vibration/shock
immunity
Open COM1 cover
Weight (g)
Input point specifications
Items
Input wiring type
Input indicator
Input voltage
Active Level
Response Time / Noise Immunity
10
Output point specifications
Items
Max. frequency
Output indicator
Min. load
Working voltage
Insulation
Current specification
Max. output
delay time
Over-current protection
Mechanical life
Open COM2 cover
Electrical life
*High-speed output points (Y0, Y2) are only in DVP20EH2 and DVP32EH2; high-speed output points (Y0, Y1, Y2, Y3, Y4, Y6) are only in
DVP40EH2.
Installation & Wiring
3.1 Dimension
W1
Remove RS-485
terminal
Part Description
COM2 (RS-485) For both master & slave modes
RUN/STOP switch PLC RUN/STOP control
VR 1
Enable M1178/corresponding
VR0
value of D1178
Enable M1179/corresponding
VR1
value of D1179
COM1 (RS-232) For slave mode
Battery Shall be changed within 1 min.
Remove memory card
16EH00 2 20EH00 2 32EH00 2 40EH00 2 48EH00 2
100 ~240VAC (-15% ~ 10%); 50/60Hz ± 5%
2A/250VAC
50VA 50VA 60VA 60VA 60VA
500mA 500mA 500mA 500mA 500mA
DC24V; output short-circuited
1500VAC (Primary-Secondary); 1500VAC (Primary-PE); 500VAC (Secondary-PE)
＞5 MΩ (all I/O point-to-ground: 500VDC)
ESD: 8KV Air Discharge; EFT: Power Line: 2KV, Digital I/O: 1KV, Analog & Communication I/O: 250V
Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV, RS: 26MHz ~ 1GHz, 10V/m
The diameter of grounding wire shall not be less than that of L, N terminal of the power. (When many PLCs are
in use at the same time, please make sure every PLC is properly grounded.)
Operation: 0ºC ~ 55ºC (temperature); 50 ~ 95% (humidity); pollution degree 2
Storage: -40 ºC ~ 70 ºC (temperature); 5 ~ 95% (humidity)
International standards: IEC1131-2, IEC 68-2-6 (TEST Fc)/IEC1131-2 & IEC 68-2-27 (TEST Ea)
500/480 520/500 652/612 710/675 748/688
Spec. 24VDC single common port input
Low speed High speed (200KHz)
Change wiring from S/S to SINK or SOURCE
LED display; light on = ON, light off = OFF
Input point X0 ~ X7, X10 ~ X17
24VDC ± 10%
can conduct 10 ~ 60ms digital
16VDC ± 10%
Off On
filter adjustment
On Off 12VDC ± 10%
10 ms 0.5us
Spec. Single common port transistor output
Single common port relay output
Low speed High speed*
10KHz 200KHz
LED display; light on = ON, light off = OFF
-
5 ~ 30VDC
Photocoupler isolation
<1KHz, 0.3A/1 point @ 40°C
0.3A/1 point @ 40ºC
≧1KHz, 30mA/1 point @ 40°C 75 VA (conductive), 90W (resistive)
Off On 20us
0.2us
On Off 30us
N/A
N/A
1.5×10
N/A times (3A 120VAC); 3×10
(5A 250VAC)
Model W (mm)
DVP16EH00R2/T2 113
DVP20EH00R2/T2 113
DVP32EH00R2/T2 143.5
DVP40EH00R2/T2 158.8
DVP48EH00R2/T2 174
DVP64EH00R2/T2 212
DVP80EH00R2/T2 276
W 82.2
3.2 Wiring terminals
S/S X0 X2 X4
X1 X3
16EH2
Y0 Y1 Y2 Y3 Y4 Y5 Y6
C0 C1 C2 C3 C4 C5 C6
X2 X4 X6
S/S X0 X10
X1 X3 X5 X7 X11
20EH2
Close the cover
+24V Y0 Y1 Y2 Y3 Y4
24G C0 C1 C2 C3 C4 Y5
S/S X0 X2 X4
X1 X3 X5
32EH2
Relay
Y0 Y1 Y3 Y4 Y5 Y7 Y10
C0 Y2 C1 Y6 C2
X2 X4
S/S X0
X1 X3 X5
64EH00 2 80EH00 2
32EH2
Transistor
Y0 Y1 Y2 Y3 Y4 Y5 Y7
C0 C1 C2 C3 C4 Y6
80VA 80VA
S/S X4 X6 X10
500mA 500mA X1 X5 X7 X11
40EH2
Relay
24G Y0 Y1 Y2 Y3 Y4
24V C0 C1 C2 C3 C4 Y5
S/S X4 X6 X10
X1 X5 X7 X11
40EH2
Transistor
24G Y0 Y1 Y2 Y3 Y4 Y5
24V C0 C1 C2
836/756 948/848
X2 X4
S/S X0
X1 X3
Note
48EH2
Y0 Y1 Y3 Y4 Y5 Y7 Y10
Y2
C0 C1 Y6
S/S X0 X2 X4
X1 X3 X5
64EH2
Y0 Y1 Y3 Y4 Y5 Y7 Y10
C0 Y2 C1 Y6 C2
Load ON/OFF control
S/S X0 X2 X4 X6
2mA/DC power supply X1 X3 X5
＜250VAC, 30VDC
80EH2
Magnetic isolation
2A/1 point (5A/COM)
Y0 Y1 Y3 Y4 Y5 Y7 Y10 Y11
C0 Y2 C1 Y6 C2
10ms
3.3 Installation
7
2×10 times (without load)

How to install DIN rail

5 5
times (5A 30VDC); 5×10
4
times
DVP-PLC can be secured to a cabinet by using the DIN rail of 35mm in height and 7.5mm
in depth. When mounting PLC to DIN rail, be sure to use the end bracket to stop any
side-to-side movement of PLC and reduce the chance of wires being loosen. A small
retaining clip is at the bottom of PLC. To secure PLC to DIN rail, place the clip onto the rail
and gently push it up. To remove it, pull the retaining clip down and gently remove PLC
from DIN rail, as shown in the figure.
W1 (mm)
How to screw
103
Please use M4 screw according to the dimension of the product.
103
133.5
Please install PLC in an enclosure with sufficient space around it to allow heat
153.8
dissipation as shown in the figure.
164
202
266
X6
X5 X7
Y7
C7
X12
X13
Y6
Y7
X6 X10 X12 X14 X16
X7 X11 X13 X15 X17
Y11 Y13 Y14 Y15 Y17
Y12 C3 Y16
X6 X12
X10 X14 X16
X7 X11 X13 X15 X17
Y10 Y11 Y13 Y14 Y16
C5 Y12 C6 Y15
Y17
X12 X14 X16 X20 X22 X24 X26
X13 X15 X17 X21 X23 X25 X27
Y6 Y10 Y12 Y14 Y16
Y7 C5 Y11 Y13 C6 Y15 Y17
X12 X14 X16 X20 X22 X24 X26
X13 X15 X17 X21 X23 X25 X27
Y6 Y7 Y10 Y12 Y14 Y16
C3 C4 Y11 Y13 C5 Y15 Y17
X6 X12 X20 X22 X24 X26
X10 X14 X16
X5 X7 X11 X13 X15 X17 X21 X23 X25 X27
Y11 Y13 Y14 Y15 Y17 Y20 Y22 Y24 Y26
C4 Y21 Y23 Y25 Y27
C2 Y12 C3 Y16
X22
X6 X10 X12 X14 X16 X20 X24 X26 X30 X32 X34 X36
X7 X11 X13 X15 X17 X21 X23 X25 X27 X31 X33 X35 X37
Y11 Y13 Y14 Y15 Y17 Y20 Y21 Y23 Y25 Y27 Y30 Y32 Y34 Y36
Y12 C3 Y16 C4 Y22 Y24 Y26 C5 Y31 Y33 Y35 Y37
X10 X12 X14 X16 X20 X22 X24 X26 X30 X32 X34 X36 X40 X42 X44 X46
X7 X11 X13 X15 X17 X21 X23 X25 X27 X31 X33 X35 X37 X41 X43 X45
Y25 Y27
Y13 Y14 Y15 Y17 Y20 Y21 Y23 Y24 Y30 Y31 Y33 Y35 Y37 Y40 Y41 Y43 Y45 Y47
Y12 C3 Y16 C4 Y22 C5 Y26 C6 Y32 Y34 Y36 C7 Y42 Y44 Y46
> 50mm
DVP MPU
> 50mm > 50mm
> 50mm
X47