Table of Contents
Advertisement
Quick Links
Instructions-Parts
26A231 Air Control
Box Kit
Interfaces Air Control Management for Spray Devices used with a ProMix
Panel Electronic Proportioner. For professional use only.
26A231 - Air Control Module
100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Pressure
Important Safety Instructions
Read all warnings and instructions in this manual
and in the PD2K Proportioner manuals, the Gun
Flush Box manual, and the Gun Air Shutoff Kit
manual. Save all instructions.
3A4497A
EN
®
PD2K Dual
Advertisement
Table of Contents
Related Manuals for Graco 26A231
Summary of Contents for Graco 26A231
- Page 1 Interfaces Air Control Management for Spray Devices used with a ProMix PD2K Dual Panel Electronic Proportioner. For professional use only. 26A231 - Air Control Module 100 psi (0.7 MPa, 7 bar) Maximum Air Inlet Pressure Important Safety Instructions Read all warnings and instructions in this manual...
-
Page 2: Table Of Contents
Graco Standard Warranty ....12 Overview Graco Information ......12 Air Control Module 26A231 provides electrical and air... -
Page 3: Installation
Installation Installation Location Install the air control module enclosure (1) within 15 ft (4.5 m) of the PD2K Dual Panel Control Enclosure, to ensure that the cable (23) will reach between the two enclosures. The equipment mush be grounded to reduce the risk Mount the Enclosure of static sparking. -
Page 4: Install The Cable
Installation Install the Cable 1. Loosen the captive screws and remove the front cover from the enclosure. 2. The cable (23) has bare wires at both ends. Thread the shortest end (4 in. [102 mm]) into the enclosure through the strain relief bushing (7). See F . - Page 5 Installation Table 2: EFCM Terminal Connections Cable Wire EFCM Pin No. Colors Pin No. Connector Black White Green Orange Blue White/Black Red/Black Green/Black Orange/Black EFCM Connectors 5-7 Blue/Black . 3. Enhanced Fluid Control Module Red/White 3A4497A...
-
Page 6: Install The Pressure Switch
Installation Install the Pressure Switch NOTE: The Air Control Module Kit does not include a 2. Connect the wires from PS#1 to the right side of the pressure switch (PS). The pressure switch is supplied terminal strip (12) pins 5 (+) & 6 (-), as indicated by with the gun flush box kit. -
Page 7: Connect The Gun Flush Box
Installation Connect the Gun Flush Box Replace the Cover NOTE: Use 5/32 in. (4 mm) OD tubing to connect the Reinstall the cover on the enclosure and secure with the gun flush box air ports to the interface module air ports, four captive screws. -
Page 8: Parts
Parts Parts TI14279a 31,34 5,17 33,34 Part No./Description Ref. Part Description Ref. Part Description 598095 TUBE, nylon; 5/32 in. OD; 50 ft. 15V531 ENCLOSURE (not shown) 15U918 LABEL, product 104641 BULKHEAD 118435 GROMMET 111763 ELBOW, 1/4 in npt. 121628 SCREW, self-sealing 119159 SWITCH, air flow 104644... -
Page 9: Dimensions
Dimensions Dimensions 4.00 in. 4.00 in. (101.6 mm) (101.6 mm) 6.75 in. (171.5 mm) 7.50 in. Mounting Holes (190.5 mm) 6.28 in. (159.5 mm) TI14276a TI14278a 3A4497A... - Page 10 Dimensions 3A4497A...
-
Page 11: Technical Data
Technical Data Technical Data 26A231 Air Control Module Metric Maximum air inlet pressure 100 psi 0.7 MPa, 7 bar Inlet/Outlet Sizes Air inlet size 1/4 in. (6 mm) OD tube connector Air exhaust port size 5/32 (4mm) OD tube connector... -
Page 12: Graco Standard Warranty
With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective.