BEA ACTIV8 THREE PULSE Quick Manual

LED-SIGNALS
The ORANGE LED The sensor goes into
fl ashes every second. security mode.
The ORANGE LED The sensor signals
an internal fault.
fl ashes 1 x.
1
The ORANGE LED Irregularities in the
fl ashes 2 x. power supply
2
The sensor receives
The ORANGE LED
fl ashes 4 x. not enough IR-energy.
4
The ORANGE LED The sensor receives
fl ashes 5 x. too much IR-energy.
5
The radar sensor output is
The ORANGE LED
faulty.
fl ashes 6 x.
6
The sensor is disturbed.
The ORANGE LED
The radar sensor encounters
fl ashes 7 x.
7
a hardware problem.
The ORANGE LED The sensor encounters
is on. a memory problem.
The RED LED fl ashes
The sensor sees the door
quickly after an
during the assisted setup.
assisted setup.
The sensor vibrates.
The RED LED
lights up
sporadically.
The sensor sees the door.
The sensor is disturbed by
lamps or another sensor.
The sensor is disturbed
by the rain.
The sensor is disturbed by
The GREEN LED
rain and/or leaves.
lights up
sporadically.
Ghosting
The sensor vibrates.
The sensor sees the door
or other moving objects.
BEA SA | LIEGE Science Park | ALLÉE DES NOISETIERS 5 - 4031 ANGLEUR [BELGIUM] | T +32 4 361 65 65 | F +32 4 361 28 58 | INFO@BEA.BE | WWW.BEA.BE
BEA hereby declares that the ACTIV8 THREE PULSE is in conformity with the basic requirements and the
other relevant provisions of the directives 1999/5/EC, 2004/108/EC and 2006/42/EC.
Notifi ed Body for EC inspection: 0044 - TÜV NORD CERT GmbH, Langemarckstr. 20, D-45141 Essen
Angleur, November 2010 Jean-Pierre Valkenberg, Authorized representative
The complete declaration of conformity is available on our website: www.bea.be
Only for EC countries: According to the European Guideline 2002/96/EC for Waste Electrical and Electronic Equipment (WEEE)
1
Cut and restore power supply.
1 Cut and restore power supply.
If orange LED fl ashes again, replace sensor.
2
1
Check power supply.
2 Check wiring.
1 Use the 1 m prism if possible.
Check the angle of the IR-curtains.
2
Use a low energy prism if possible.
1
Check the angle of the IR-curtains.
2
1 Replace sensor.
1
Change radar antenna angle.
Replace sensor.
1
1
Cut and restore power supply.
2 If orange LED lights up again, replace sensor.
1 Check the angle of the IR-curtains.
2 Launch a new assisted setup.
Attention: Do not stand in the detection fi eld!
Check if the sensor is fastened fi rmly.
1
2 Check position of prism and cover.
1 Launch an assisted setup and adjust the IR angle.
1 Choose a different frequency by remote control.
1
Increase the IR-immunity fi lter to value 2 or 3.
Increase radar-immunity fi lter by remote control.
1
Change radar antenna angle.
1
1 Check if the sensor is fastened fi rmly.
2
Check position of cable and cover.
1 Remove the objects if possible.
2 Change radar antenna.
3 Change radar fi eld size (sensitivity).
Please keep for further use
Designed for colour printing
Other use of the device is outside the
permitted purpose and can not be
guaranteed by the manufacturer.
The manufacturer cannot be held
responsible for incorrect installations or
inappropriate adjustments of the sensor.
DESCRIPTION
4
3
2
1 1. IR-prism
(2 m)
2. radar antenna
(wide fi eld)
3. radar antenna
(narrow fi eld)
4. cover
TECHNICAL SPECIFICATIONS
Supply voltage: 12 V - 24 V AC +/-10% ; 12 V - 30 V DC -5%/+10%
Power consumption: < 3 W
Mounting height: 1.8 m to 4 m
(< 3 m to enable DIN 18650-conformity)
Temperature range: -25 °C to +55 °C
Degree of protection: IP54
Expected lifetime: 5 years
Norm conformity: R&TTE 1999/5/EC; EMC 2004/108/EC; MD 2006/42/EC; EN 12978
EN ISO 13849-1:2008 Performance Level «d» CAT. 2
(under the condition that the door control system monitors the sensor at least once per door cycle)
GREEN
LED
Detection mode: Motion
Min. detection speed: 5 cm/s
Technology: Microwave doppler radar
Transmitter frequency: 24.150 GHz
Transmitter radiated power: < 20 dBm EIRP
Transmitter power density: < 5 mW/cm2
From 15 ° to 50 ° vertical (adjustable)
Angle:
0.5 s to 9 s (adjustable)
Hold time output signal:
Potential linked current source
Output/Input:
No detection: current source ON
Max. open circuit voltage: 6.5 V
Output voltage available at 10 mA: 3 V min.
Typical load: up to 3 optocouplers in series
Detection: current source OFF
Leakage current: < 100 μA
Open-circuit remained voltage: < 500 mV
S S pecifi cations are subject to changes without prior notice.
All values measured in optimal conditions. All values measured in optimal conditions.
ACTIV8 THREE PULSE
Opening & safety sensor
for automatic sliding doors in escape routes
5. push buttons
6. IR-curtain ajustment screw
7. main connector
(to be operated from SELV compatible power supplies only)
RED
LED
Presence
Typical response time: <128 ms (max. 500 ms)
Active infrared with background analysis
Spot diameter: 0.1 m (typ)
Number of spots: 24 or 12 by curtain
Number of curtains: 2
From -4 ° to +4 ° (adjustable)
0.3 s to 1 s (not adjustable)
Transistor (NPN open collector) requiring ext. pull-up resistor
Max. output current: 25 mA
Max. switching power: 40 V DC
Max. pulse amplitude (detection state or fail state): 0,8 V
Input Impedance: 100 kΩ
Max. input voltage: 30 V DC
External pull-up resistor: < 470 Ω (check compatibility)
Min. Pulse amplitude (Vpp): > 50% of sensor supply voltage
Max. Pulse duration: 100 μs @ 25 mA output current
Min. time interval between pulses: > pulse duration
5
6
7