Subscribe to Our Youtube Channel
Related Manuals for Phoenix Mecano Dewert Okin CU458-2
Summary of Contents for Phoenix Mecano Dewert Okin CU458-2
- Page 1 CONTROL UNIT CU458-2 Installation Instructions (Translation of the original installation instructions)
-
Page 3: Foreword
CU458-2 Foreword Foreword Document revision history Version Date Modification, change 03/2020 First release Disclaimer and exclusion of liability DewertOkin is not responsible for damage resulting from: • failure to observe these instructions, • changes made to this product which have not been approved by DewertOkin, or •... -
Page 4: Table Of Contents
Table of Contents CU458-2 Table of Contents Foreword Document revision history Disclaimer and exclusion of liability Creation of a complete operating instruction manual for the entire end product Table of Contents General Information Configurations About these installation instructions Conventions used Safety notices Proper and intended usage Selection and qualification of personnel... -
Page 5: General Information
CU458-2 General Information General Information Configurations The designation CONTROL UNIT is used in these installation instructions to refer to the CONTROL UNIT CU458-2. About these installation instructions In order to install the CONTROL UNIT successfully and safely in the end product, these installation instructions must be observed. -
Page 6: Safety Notices
Safety notices CU458-2 Safety notices Proper and intended usage The CONTROL UNIT is intended for use: • as a control unit for suitable DewertOkin drive systems, • for HOME applications (in beds, reclining chairs, etc.). CAUTION Risk of accident This CONTROL UNIT should only be used for the applications described above. Any other use is forbidden. -
Page 7: Selection And Qualification Of Personnel
CU458-2 Safety notices Selection and qualification of personnel The installation of the CONTROL UNIT in the end product may only be performed by qualified per- sonnel. Electrical safety 2.2.1 CAUTION Electric shock Be careful; there is a risk of electrical shock! Before installing, make sure that you disconnect the external DewertOkin power supply for the CONTROL UNIT from the power outlet! The CONTROL UNIT should not be used! You must properly dispose of malfunctioning or broken units. -
Page 8: Ratings Plate
Safety notices CU458-2 Ratings plate The ratings plate shown is an example; The specifications for your CONTROL UNIT may differ from this illustration. Figure 1 Ratings plate for the CONTROL UNIT (example) CU458-2 Model name xxxxx Article number Model No. Model number 24 –... -
Page 9: Possible Combinations
CU458-2 Possible combinations Possible combinations The CONTROL UNIT can be used together with multiple drives, vibration motors and accessories that have been approved by DewertOkin. A tailored system consists of the combination of control unit, drive, vibration motor, accessories, and hand-held remote. DewertOkin has separate system instruction manuals containing the additional information and in- structions needed for these systems. -
Page 10: Description
Description CU458-2 Description The CONTROL UNIT is a control unit and for one or more DewertOkin vibration motors. An exter- nal DewertOkin power supply unit is used to connect the CONTROL UNIT to the mains power. Components The housing of the CONTROL UNIT has a connection for an external DewertOkin drive system, as well as connections for vibration motors and various accessories. -
Page 11: Technical Specifications
CU458-2 Technical specifications Technical specifications Input voltage 24 – 29 V DC Current consumption at nominal operations Max. 6 A in intermittent operations Mode of operations Intermittent duty 2 min./18 min. Protection class Protection degree IP20 Dimensions and weight Length x width x height 182 mm x 135 mm x 30 mm Weight Approx. - Page 12 Technical specifications CU458-2 Figure 3 Dimensions of the CONTROL UNIT, top view (in mm) Figure 4 Dimensions of the CONTROL UNIT, side view (in mm) 93728 1.0...
-
Page 13: Installation
CU458-2 Installation Installation Safety notices to observe during installation Basic safety rules must be followed in order to ensure that the end product can be continually op- erated in a safe manner. These rules must be observed while using the end product and while in- stalling the CONTROL UNIT in the end product. - Page 14 Installation CU458-2 CAUTION You should only connect and disconnect the cables when they are completely disconnected from any live current! Pull out the power supply plug from the plug socket. Screw the control unit onto the end product (as shown in Figure 6). Use the mounting holes shown in Figure 5 located on the control unit.
- Page 15 CU458-2 Installation Electrical connection 6.2.2 CAUTION Electric shock Electrical components should be connected or disconnected only when the power supply is un- plugged. There is a delay after the supply voltage is applied before the device actually turns on. Wait at least 2 seconds before initial commissioning.
-
Page 16: Information About Creating Your Operating Manual
Information about creating your Operating Manual CU458-2 Information about creating your Operating Manual The factual information contained within may be used when you are creating the end-product man- ual. The installation instructions do not contain all information required for the safe operation of the end product. -
Page 17: Configuring The Hand-Held Remote And App
CU458-2 Information about creating your Operating Manual Shutting down the CONTROL UNIT in the event of an emergency In an emergency, disconnect the mains power plug from its socket in order to shut off the connect- ed drive, the accessory, and the vibration motors. The power plug must always be accessible dur- ing operations so that it is possible to shut down the CONTROL UNIT. - Page 18 Information about creating your Operating Manual CU458-2 3 If, during the RF1058 remote's pairing process, you press any button on an already paired RF1058 hand-held remote, then it switches to the Bluetooth ® pairing mode. If the RF1058 remote or a Bluetooth ®...
-
Page 19: Troubleshooting
CU458-2 Troubleshooting Troubleshooting This chapter describes troubleshooting methods for fixing problems. If you experience an error that is not listed in this table, please contact your supplier. Only qualified specialists who have received electrician training should carry out troubleshooting and repairs. -
Page 20: Maintenance
Maintenance CU458-2 Maintenance The CONTROL UNIT requires no maintenance. Cleaning and care The CONTROL UNIT was designed so that it would be easy to clean. Its smooth surfaces simplify the cleaning process. Clean the CONTROL UNIT as needed using a dry cloth. NOTICE •... -
Page 21: 10. Disposal
CU458-2 Disposal 10. Disposal 10.1 Packaging material The packaging material should be sorted into recyclable components and then disposed of in ac- cordance with the appropriate national environmental regulations (in Germany according to the re- cycling law KrWG from 01.06.2012; internationally according to the EU Directive 2008/98/EC (Waste Framework Directive WFD as of 12.12.2008)). -
Page 22: Additional Information
Additional information CONTROL UNIT CU458-2 • UL962 • CSA C22.2 No. 68-09 FCC Warning This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 23 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- Page 24 This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence- exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
- Page 25 DewertOkin GmbH Weststrasse 1 Kirchlengern 32278, Germany Tel: +49 (0)5223/979-0 Fax.: +49 (0)5223/75182 http://www.dewertokin.de Info@dewertokin.de ID No.: 93728...
Need help?
Do you have a question about the Dewert Okin CU458-2 and is the answer not in the manual?
Questions and answers