Page 1
Graphical Digital Panel Meter WPMZ-1/3 RS-232C Originalcommand/Originaloutput communication manual IM-0885-02 Ver.1.00 Watanabe Electric Industry Co., Ltd.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 Table of contents If you read this manual on a pc, you can jump to linked destination by clicking characters in blue. INTRODUCTION ............................4 1. OVERVIEW ............................. 5 1-1.
Page 3
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-33. MAXA OFF command ........................ 24 4-1-34. MAXB command ......................... 25 4-1-35. MAXB ON command ........................25 4-1-36. MAXB OFF command ........................ 25 4-1-37. MAXAB command ........................26 4-1-38. MAXAB ON command ....................... 26 4-1-39.
Page 4
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-2-2. MLTA ON command ........................44 4-2-3. MLTA OFF command ........................44 4-2-4. MLTB command ........................... 45 4-2-5. MLTB ON command ........................45 4-2-6. MLTB OFF command ........................45 4-2-7.
This instruction manual explains notes and information on using WPMZ series "original command" "original output" communication. The Modbus RTU protocol can also be used with the WPMZ series RS - 232C output mounted products. For the Modbus RTU protocol, another manual is available so please inquire.
1. Overview Describe the specifications of WPMZ series original command communication. This manual is intended for engineers who connect WPMZ series to the the master device and create control / data collection processing. As a master device, it is assumed to be a PC or Programmable Logic Controller (PLC). Please prepare the equipment to be used for the master in advance.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 2. Communication condition 2-1. Supported Modules The corresponding modules assumed in this manual are as follows. ・WPMZ-1 ・WPMZ-3 2-2. Communication condition of module The communication conditions for connecting to each module are as shown in the table below.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 3. Originalcommand communication specification Describe the behavior when protocol setting is set to "originalcommand". The originalcommand is a single master / single slave method. A message is sent from one master to the slave (WPMZ).
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 For each baud rate, the transmission interval with Original output setting is as follows. baud rate-Transmission cycle table 3.1 baud rate Transmission cycle (msec) 9600bps 150msec 19200bps 100msec 38400bps 50msec 3-3.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4. Originalcommand In this section, the command when the protocol setting is "Originalcommand" is described. If protocol setting is "Originaloutput", refer to chapter 5 and later. 4-1. Common Command to WPMZ-1 and 3 The command of WPMZ - 1/3 is explained below.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-1. DSPA command DSPA is a command that responds to the display value of the instantaneous value of Ach and the comparison result. Command CR LF Response (In 99999 display, AL1 to AL4 are allotted to instantaneous value Ach, and all channels are turned ON)...
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 DifferenceHold : MD (WPMZ-3 only) 3rd character…polarity indication at maximum digit number. If there is no polarity at maximum digit, blank. 4th to 10th characters…Display value. If there are no decimal points and the number of digits is small, right-justified.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-4. MESA command MESA is a command that responds to the displayed value of the instantaneous value of Ach. Command CR LF Response (Response of condition displaying 0) CR LF Response (Response of condition displaying 0.15)...
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-5. MESB command MESB is a command that responds to the instantaneous value display value of Bch. Command CR LF Response…Same as MESA command. 4-1-6. MESC command MESC is a command that responds to display value of instantaneous calculation value.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-7. JGMA command JGMA is a command that responds to the comparison result of instantaneous value of Ach. Command CR LF Response (Assign AL1 to AL4 to instantaneous value Ach, and respond when all channels are turned ON.)...
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-8. JGMB command JGMB is a command that responds to the comparison result of instantaneous value of Bch. Command CR LF Response Same as JGMA command. 4-1-9. JGMC command JGMC is a command that responds to the comparison result of the instantaneous calculation value.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-10. COMR command COMR is a command to check the instruction status of “CompareReset”. Instruction state with "COMR ON" and "COMR OFF" command is returned instead of the actual “CompareReset”...
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-13. HDRA command HDRA is a command to check the instruction status of “HoldReset” of Ach. Instruction state with "HDRA ON" and "HDRA OFF" command is returned instead of the actual “HoldReset”...
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-16. HDRB command HDRB is a command to check the instruction status of “HoldReset” of Bch. Instruction state with "HDRB ON" and "HDRB OFF" command is returned instead of the actual “HoldReset”...
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-19. HDRAB command HDRAB is a command to check the instruction status of “HoldReset” of Ach and Bch. Instruction state with "HDRAB ON" and "HDRAB OFF" command is returned instead of the actual “HoldReset”...
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-22. DHDA command DHDA is a command to check the indication state of holding the current value of Ach. Instruction state with "DHDA ON", "DHDA OFF" command is returned instead of the actual current value holding state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-25. DHDB command DHDB is a command to check the indication state of holding the current value of Bch. Instruction state with "DHDB ON", "DHDB OFF" command is returned instead of the actual current value holding state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-28. DHDAB command DHDAB is a command to check the indication state of holding the current value at the same time for Ach and Bch. Instruction state with "DHDAB ON" and "DHDAB OFF" command is returned instead of the actual current value holding state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-31. MAXA command MAXA is a command to check the indication state of Ach maximum value preservation. Instruction state with "MAXA ON", "MAXA OFF" command is returned instead of the actual maximum value holding state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-34. MAXB command MAXB is a command to check the indication state of holding maximum value of Bch. Instruction state with "MAXB ON", "MAXB OFF" command is returned instead of the actual maximum value holding state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-37. MAXAB command MAXAB is a command to check the indication state of holding the maximum value of Ach and Bch at the same time. Instruction state with "MAXAB ON", "MAXAB OFF" command is returned instead of the actual maximum value holding state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-40. MINA command MINA is a command to check the indication state of holding minimum value of Ach. Instruction state with "MINA ON", "MINA OFF" command is returned instead of the actual minimum value holding state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-43. MINB command MINB is a command to check the indication state of holding minimum value of Bch. Instruction state with "MAXB ON", "MAXB OFF" command is returned instead of the actual minimum value holding state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-46. MINAB command MINAB is a command to check the indication state of holding the miniimum value of Ach and Bch at the same time. Instruction state with "MINAB ON", "MINAB OFF" command is returned instead of the actual minimum value holding state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-49. AMPA command AMPA command is a command to check the “AmpHold” indication state of Ach. Instruction state with "AMPA ON" and "AMPA OFF" command is returned instead of the actual operation state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-52. AMPB command AMPB command is a command to check the “AmpHold” indication state of Bch. Instruction state with "AMPB ON" and "AMPB OFF" command is returned instead of the actual operation state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-55. AMPAB command AMPAB is a command to check the “AmpHold” indication state of Ach and Bch at the same time. Instruction state with "AMPAB ON" and "AMPAB OFF" command is returned instead of the actual operation state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-58. DEVA command DEVA command is a command to check the “DevHold” indication state of Ach. Instruction state with "DEVA ON" and "DEVA OFF" command is returned instead of the actual operation state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-61. DEVB command DEVB command is a command to check the “DevHold” indication state of Bch. Instruction state with "DEVB ON" and "DEVB OFF" command is returned instead of the actual operation state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-64. DEVAB command DEVAB is a command to check the “DevHold” indication state of Ach and Bch at the same time. Instruction state with "DEVAB ON" and "DEVAB OFF" command is returned instead of the actual operation state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-67. AVEA command AVEA command is a command to check the “AveHold” indication state of Ach. Instruction state with "AVEA ON" and "AVEA OFF" command is returned instead of the actual operation state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-70. AVEB command AVEB command is a command to check the “AveHold” indication state of Bch. Instruction state with "AVEB ON" and "AVEB OFF" command is returned instead of the actual operation state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-73. AVEAB command AVEAB is a command to check the “AveHold” indication state of Ach and Bch at the same time. Instruction state with "AVEAB ON" and "AVEAB OFF" command is returned instead of the actual operation state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-76. DZRA command DZRA command is a command to check the digital zero indication state of Ach. Instruction state with "DZRA ON" and "DZRA OFF" command is returned instead of the actual operation state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-79. DZRB command DZRB command is a command to check the digital zero indication state of Bch. Instruction state with "DZRB ON" and "DZRB OFF" command is returned instead of the actual operation state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-82. DZRAB command DZRAB is a command to check the digital zero indication state of Ach and Bch. Instruction state with "DZRAB ON" and "DZRAB OFF" command is returned instead of the actual operation state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-85. TRDT command TRDT command is a command to check the “TrendTrigger” indication state. Instruction state with "TRDT ON" command is returned instead of the actual operation state. Command CR LF Response(No instruction)...
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-1-87. PCHG command PCHG is a command that responds to the actual pattern number that is running. Command G CR LF Response(Under the condition operating with pattern 1) CR LF Response(Under the condition operating with pattern 8)...
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-2. Dedicated commands for WPMZ-3 This section shows dedicated commands for WPMZ-3. 4-2-1. MLTA command MLTA command is a command to check the “MultiHold” indication state of Ach. Instruction state with "MLTA ON" and "MLTA OFF" command is returned instead of the actual operation state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-2-4. MLTB command MLTB command is a command to check the “MultiHold” indication state of Bch. Instruction state with "MLTB ON" and "MLTB OFF" command is returned instead of the actual operation state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-2-7. MTSA command MTSA command is a command to get the “MultiHold” parameters of Ach. MTSA returns displayed value, overall result and operation state. Command CR LF Response (Condition : displaying [99999], overall result is [indeterminate] and operation state is [S1 running] )...
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-2-8. MT1A command MT1A command is a command to get the “MultiHold” parameters of section 1 of Ach. MT1A returns displayed value, section alarm condition and operation state. Command...
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-2-12. MTSB command MTSB command is a command to get the “MultiHold” parameters of Bch. MTSB returns displayed value, overall result and operation state. Command CR LF Response is the same as Ach (MTSA command).
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-2-17. WVCA command WVCA command is a command to check the “WaveComp” indication state of Ach. Instruction state with "WVCA ON" and "WVCA OFF" command is returned instead of the actual operation state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-2-20. WVCB command WVCB command is a command to check the “WaveComp” indication state of Bch. Instruction state with "WVCB ON" and "WVCB OFF" command is returned instead of the actual operation state.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 4-2-23. WVSA command WVSA command is a command to get the “WaveComp” parameters of Ach. WVSA returns displayed value, overall result and operation state. Command CR LF Response (Condition : displaying [99999], overall result is [indeterminate] and operation state is [Running] )...
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 5. OriginalOutput communication specification Describe the behavior when the protocol setting is "OriginalOutput". Refer to "4. OriginalCommand" for the state of protocol setting "OriginalCommand". 5-1. WPMZ-1/3 The original output of WPM - 1/3 will be explained below.
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 6. trouble shooting 6-1. About communication 6-1-1. In a state where communication can not be performed If you can not communicate, please check the contents below. Are all the devices related to communication turned on? ...
Page 55
WPMZ Series RS-232C OriginalCommand/OriginalOutput Operation Communication Manual IM-0885-02 Number of pages:54 The contents of this instruction manual are subject to change without prior notice. WATANABE ELECTRIC INDUSTRY CO.,LTD. http://www.watanabe-electric.co.jp/en/ 6-16-19,JINGUMAE,SHIBUYA-KU,TOKYO 150-0001,JAPAN TEL +81-3-3400-6147 FAX +81-3-3409-3156 IM-0885-01...