Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SaMASZ MOP 120K
Summary of Contents for SaMASZ MOP 120K
- Page 1 Poland, 15-161 Białystok, ul. Trawiasta 15 Established – 1984 tel. (+48) 664 70 31 fax (+48) (85) 664 70 41 e-mail: samasz@samasz.pl www.samasz.pl OPERATOR'S MANUAL TRACTOR SWEEPER MOP 120K; MOP 140; MOP 160; MOP 200 IN122EN004 27.03.2015 EDITION NO. 4 Original manual...
- Page 2 NOTE: Mount rubber guard due to the fact that hard objects (stones, wood pieces, etc.) are likely to be thrown by sweeps NOTE: Prior service works turn tractor’s drive off and take ignition key out. NOTE: Operating sweeper without previous familiarizing with its contents as well as by unauthorized personnel, particularly by children, is strictly forbidden.
-
Page 3: Table Of Contents
Tractor sweeper Operator's manual Table of contents 1. IDENTIFYING THE MACHINE ....................2 2. INTRODUCTION .......................... 2 3. TECHNICAL DESCRIPTION ...................... 3 3.1. Technical data ........................3 3.2. Machine design ........................4 3.3. Designation ..........................5 4. SAFETY CONDITIONS ....................... 5 4.1. -
Page 4: Identifying The Machine
Tractor sweeper Operator's manual 1. IDENTIFYING THE MACHINE Data plate is permanently mounted on the sweeper's main frame in place shown below on Fig. 1 and Fig. 2. Fig. 1. Data plate placement on sweeper Fig. 2. Data plate Data plate includes: A. -
Page 5: Technical Description
Operating sweeper without previous familiarizing with its contents as well as by unauthorized personnel, particularly by children, is strictly forbidden. TECHNICAL DESCRIPTION 3.1. Technical data SaMASZ® manufactured sweepers feature the following parameters: Tab. 1. Technical data Machine type MOP 120K MOP 140... -
Page 6: Machine Design
Tractor sweeper Operator's manual 3.2. Machine design Sweeper comprises the following assemblies (Fig. 3): 1 - body, 2 - container for impurities, 3 - sweep assembly, 4 - hydraulic drive, 5 -extension arm with traction wheel (2 pcs), 6 - 3-point linkage Cat. 2, 7 - support, 8 - optionally: hydraulic emptying of container or manual latch with link, 9 - side sweep arm,... -
Page 7: Designation
NOTE: Do not use the machine for purposes other than abovementioned. Well-proven design and quality materials ensure high reliability and durability of SaMASZ machines. 4. SAFETY CONDITIONS Prior to any operation with tractor sweeper read the operator's manual carefully. -
Page 8: Safety Rules When Driving On Public Roads
Residual risk Residual risk description NOTE! Despite the fact, that SaMASZ company – the manufacturer of sweeper takes responsibility for the sweeper's design and manufacturing, in order to eliminate risk, certain elements of residual risk when operating the sweeper are unavoidable. - Page 9 Tractor sweeper Operator's manual Danger of wound Possible, when replacing operating parts with sharp edges. For any repair and maintenance works always wear safety gloves. PROHIBITIONS! Bear in mind the following bans when operating the machine. It is forbidden to perform the following: use the sweeper for purposes other than mentioned herein, any self-modifications and repairs, operating sweeper by minors as well as not being learned with content of the operator's manual...
-
Page 10: Transport
Tractor sweeper Operator's manual 4.3. Transport Sweeper is dispatched as completely mounted. Sweeper should be transported with trucks paying attention to road traffic safety. In order to load the 1- info sign - point machine onto a transport mean use additional devices of attachment for lifting. -
Page 11: Servicing And Operating
Tractor sweeper Operator's manual NOTE: a) all warning decals (labels) should be clean and legible, b) lost or damaged decals (labels) must be replaced with new ones, c) new decals (labels) may be ordered at the manufacturer, SERVICING AND OPERATING Prior to operation commencement: visually assess condition of sweeper, and if any defects are found have repair immediately, mount the sweeper onto 3-point linkage frame,... -
Page 12: Dismounting Container For Impurities
Tractor sweeper Operator's manual Dismounting container for impurities In order to empty the container: a). unscrew bolts M10 on sweeper's body (1) (Fig. 7.) and take rubber guard grip bar. b). unscrew bolts M10 (2) from container grip bar and take off rubber guard (Fig. 8.). c). -
Page 13: Adapting Sweeper To Sweep Up Impurities To The Left Or To The Right
Tractor sweeper Operator's manual 5.2. Adapting sweeper to sweep up impurities to the left or to the right In order to prepare the sweeper to sweep up impurities to the left or to the right, firstly dismount the container and leave the rubber guard at the sweeper. Sweeper can be rotated thanks to adjustment bar item 10 (Fig. -
Page 14: Optional Equipment
Tractor sweeper Operator's manual 4. Take out shaft from the body by pulling to point of connection with engine. 5. Unscrew three bolts M10, take off drive plate, plastic sweeps, metal sweeps and spacers. NOTE! Remember the arrangement of sweeps and spacers. 6. -
Page 15: Side Sweep
Tractor sweeper Operator's manual 6.1. Side sweep Side sweep is installed at the right of the sweeper (Fig. 12). Application of the sweep is aimed at sweeping out impurities from under curbs. Adjusting the side sweep is largely dependant upon condition of the main sweep. Use shaft pin (1) to adjust sweep working height. Fig. - Page 16 Tractor sweeper Operator's manual Fig. 14. Side brush mounting points 1 - holes ∅11 for brush arm mounting bolts. 2 - holes ∅11 for arm guide assembly bolts. 3 - bracket for mounting three-way distributor for hydraulics operation control. If items „1” and „3” above meet installation requirements, unlike item „2” only, an adequate arm guide can be purchased at the sweeper's manufacturer as a spare part (see: parts catalogue).
- Page 17 Tractor sweeper Operator's manual 8) Install three-way distributor (it. 17) with bolts M6x50 (2 pcs), re-tighten hoses from side brush motor (it. 21, 22) and other hydraulic hoses (it. 24) – and main supply hose (it. 23). Note: motor hose II (it. 23) is to replace the original supply hose being available as the sweeper equipment.
-
Page 18: Water Sprinkler System
Tractor sweeper Operator's manual Fig. 16. Rotation direction: a) main brush, b) side brush 6.2. Water sprinkler system Sweeper equipped with sprinkler system can be used to effectively sweep in places, where operation in excess dust is not recommenced and even impossible. The set comprises: water tank 120l, filter,... - Page 19 Tractor sweeper Operator's manual Fig. 17. Water spray system mounting points – requirements. 1 - mounting brackets for foot of the water spray system frame. 2 - right and left bracket for mounting sprayer bar. All footnotes regarding assembly parts are in reference to items in Table-6 of the sweeper's parts catalogue.
- Page 20 Tractor sweeper Operator's manual 1) Unscrew bolts M10x30 on container frame feet set (it. 20) and insert bolts with heads up in the bracket channel on the sweeper's body (Fig. 19). Adjust the container frame set on the bolts, pre-tighten all nuts (pay attention to washers).
-
Page 21: Hydraulic Emptying Of Container For Impurities
Tractor sweeper Operator's manual 6.3. Hydraulic emptying of container for impurities Sweeper can be equipped with either manual or hydraulic system of emptying the container. In case of the hydraulic one, cylinder is mounted on the left side of the sweeper (Fig. 23) on specially prepared extension arm (1) and handle mounted directly to the container's side wall (2). - Page 22 Tractor sweeper Operator's manual To install a hydraulic discharge unit set the sweeper on an even, paved ground, and then proceed as follows on Fig. 25: 5) If the sweeper is not equipped with an adjusted arm of a catch used to mount the cylinder, dismount the previous arm and then install the catch arm set (it.
-
Page 23: Defects And Their Repair
Tractor sweeper Operator's manual Should there be any doubt whether the connected system works properly, power off and try to fix the defect. If the defect cannot be removed or its removal may breach the warranty conditions, contact your dealer or the manufacturer's service to clear off the problem. DEFECTS AND THEIR REPAIR Symptoms of Reasons of defect... -
Page 24: Storing And Maintenance
Tractor sweeper Operator's manual STORING AND MAINTENANCE Upon completion of operation: clean the sweeper thoroughly from any trace of impurity, examine condition of sweeps (replace worn sweeps with new ones), examine condition of paintwork; if any defects are found - remove rust spots, degrease, cover with primer and surface paint, examine condition of link visually;... -
Page 25: Dismounting And Withdrawal From Use
Parts gathered as a result of withdrawal from use or dismounting should be protected from access of children and animals. WARRANTY CARD TRACTOR SWEEPER MOP Machine type Machine name MOP 120K MOP 140 Tractor sweeper MOP 160 MOP 200 Serial number... -
Page 26: Warranty Terms
3. Faults or damages should be submitted personally, on letter or by telephone. Repairs shall be carried out within 14 days. Any repair which is subject to warranty should be carried out by an authorized SaMASZ dealer. 4. Warranty claims regarding replacing of the product or repayment are considered within 14 days by the Manufacturer. -
Page 27: Warranty Repairs Record
Tractor sweeper Operator's manual 12.2. Warranty repairs record Repairs scope and spare parts replaced: Date, stamp and signature of repair shop. Date, stamp and signature of repair shop. Date, stamp and signature of repair shop. - 25 -...