Advertisement
1995-99 Chevrolet Cavalier
RADIO REMOVAL:
1. Extract one screw from the front center defroster
vent on top of the dashboard.
2. Using a panel removal tool carefully snap out the vent and remove it.
3. Extract one 7mm
hex head screw from
under defrost vent.
4. Using a panel removal
tool remove the left dash
side panel surrounding
the fuse block opening
and remove one 7mm
screw from that location.
5. Using a panel removal tool release the
panel at the right side of the dash and
remove one 7mm screw behind.
6. Open glove box, extract three screws
holding the front edge of the dash panel.
7. Extract two brass 7mm screws from access hole in the roof of glove box securing metal bracket.
8. Carefully release fastening clips securing the top of the dash panel above the instrument cluster,
lift the panel up and away to remove.
CAUTION!: Passenger airbag cover is attached to the dash panel and will come off with the panel.
USE EXTREME CARE WHEN WORKING AROUND THE INNER AIRBAG SKIN!
9. Extract three 7mm screws from the radio trim bezel and use a panel removal tool to release the snap
clips around the radio and steering column.
10. Unplug bezel and remove.
11. Extract two screws holding radio in, unplug and remove radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1991-94 Chevrolet Cavalier
RADIO REMOVAL:
1. Using a panel removal tool/screwdriver,
carefully remove the radio trim
bezel by prying it outward to
release the clips securing it
to the dash.
2. Extract the two screws securing the radio
to the dash. Pull the radio out of the cavity,
unplug all the connectors and remove the radio.
USE THE SUPPLIED CARRIAGE BOLTS & NUTS TO MOUNT THE FACTORY RADIO BRACKET ON THE BOTTOM OF THE KIT.
Usa los pernos de porte y tuercos para montar el soporte de radio de la fabrica en el fondo del estuche.
1985
/
-90 Chevrolet Cavalier RS, Z24
1
2
RADIO REMOVAL:
(All Z24 Models, RS Models through 1988)
1. Carefully pull outward on the console/radio trim panel.
Spring clips are located along the top, middle and bottom of the panel.
2. Pull the panel away from the dash, disconnect the ashtray light and remove the panel.
3. Loosen two nuts along the bottom of the radio chassis.
4.
Pull the radio out, disconnect the connectors and remove the radio.
RADIO REMOVAL:
(1989-90 RS Models)
1. Carefully pull outward on
the console/radio trim panel.
Spring clips are located along
the top, middle and bottom
of the panel.
2. Pull the panel away from the dash,
disconnect the ashtray light
and remove the panel.
3. Loosen two nuts along the bottom of the radio chassis.
4. Pull the radio out, disconnect the connectors and remove the radio.
USE THE SUPPLIED CARRIAGE BOLTS & NUTS TO MOUNT THE FACTORY RADIO BRACKET ON THE TOP OF THE KIT.
Usa los pernos de porte y tuercos para montar el soporte de radio de la fabrica arriba del estuche.
"C1" BRACKET USE HOLE #2
"C1" SOPORTE USA
ABERTURA NO. 2
USE THIS END OF SLOT
USA ESTA PARTE DE
LA ABERTURA
FLANGE NUT
TUERCO REBORDE
LEFT SIDE
LADO IZQUIERDA
FRONT OF KIT
FRENTE DE
ESTUCHE
BOTTOM
FONDO
15
Read pages 3-6
for kit assembly.
"D1" BRACKET USE
HOLE #2
"D1" SOPORTE USA
RIGHT SIDE
ABERTURA NO. 2
LADO DERECHO
Read pages 3-6
for kit assembly.
BOTTOM
FONDO
USE THIS HOLE
USA ESTE AGUJERO
Read pages 3-6
for kit assembly.
TOP
TOPE
CARRIAGE BOLT
PERNO DE PORTE
Advertisement
