Amico Falcon IT Installation And Adjustment Instructions

Installation and Adjustment Instructions
Quick Setup
Falcon IT (FIT)
It is the responsibility of the end user to ensure all aspects of the installation are covered by following the full manual at:
http://www.amico.com/files/product/files/acc_im_falcon_it_station.pdf
Installation Tools & Reference
FIT
1 Swivel Post
For mounting and positioning of monitor
2 Extension Arm
extension arm to increase movement range of AHM (if applicable)
3 Mounting Adapter
Different mounting adapters will be provided based on the rail system
used
4 Cable Management
Manage cables for the FIT Station for a clutter free environment
5 Height Locking Lever
Locks arm at desired height
6 Counter Balance Bolt
Balance the weight of the monitor on the AHM arm of the FIT station
7 Negative Tilt Knob
Tilts the keyboard tray's back downwards for proper ergonomics in
certain cases
8 Keyboard Tray
(2 x mousepad, 12 x dual lock coins provided; wrist rest if purchased)
Location for Keyboard & Mouse
9 Rail System
For mounting the FIT station, varies depending on user's selection. Rail
is packed separately and must be installed first
10 VESA Head
For mounting the monitor
1. Installation to Structure
Mounting on an MRS Rail
4 x 1/4-20 Set screws
Use 1/8" (3mm) hex key
to tighten
*WARNING: Never attempt to mount or remove the arm from the rail when a monitor is installed.
*WARNING: Support AHM arm until the set screws are tightened, AHM arm can slide down when
set screws are not tightened.
Mounting on a VRS/Ohmeda Rail
Angle the AHM from the left of the channel and guide the
adapters into the groove of the channel. Tighten screw with a
3/16'' HEX key when V-adapter is at the desired height. When
tightened, the screw will protrude from the other side. Fasten the
nut to the screw to secure the V-adapter. If the nut cannot be in-
stalled, the adapter is not properly engaged. Check that all nuts
and screws are tightened to ensure the V-Adapter is locked.
VRS
Mounting
Adapter Channel
ARS
ARS Adapter
Rail
installed
Toll Free Tel: 1.877.264.2697 l Tel: 905.763.7778
Fax: 905.763.8587
Medical Facility Responsibility
9
2
3
11 Mouse/Scanner Holder
For storing mouse and hand-held scanners
Mounting on a Headwall
Pop out the cover from the Mounting Adapter Channel
to access the screws. Remove the 2 screws and lock
washers to free bottom Mounting Adapter. Install it into
the bottom rail by angling the upper lip into the inside
lip of the ARS, pull the lever back against the Mounting
Adapter and push the adapter into the rail. Once secure,
release the lever.
Install the remaining Mounting Adapter into the top ARS
the same way as step 1, ensuring the 2 holes on the bot-
tom Mounting Adapter can be seen through the Mounting
Adapter Channel. Secure the Channel to the bottom
Mounting Adapter using the screws and lock washers you
removed in step 1.
10
1
6
5
7
4
11
2. Installation to Monitor
Front of the VESA 75/100
Figure 1
1. Determine the monitor mounting configuration. VESA 75 (75 mm x 75 mm M4 thread) or
VESA 100 (100 mm x 100 mm M4 threads).
2. VESA 100 configuration: 2 screws are partially threaded into the top 2 holes in the back
of the monitor. The monitor can then be hung up on the VESA Head through the two slots
at the top. Insert 2 more screws through the VESA-100 mounting holes at the bottom and
tighten all screws (Figure 1).
3. VESA-75 configuration: Rotate the VESA Head so the 2 slots for the VESA-75 configura-
tion are located at the top. Partially thread two screws into the top 2 holes in the back of the
monitor. The monitor can then be hung up on the VESA Head through the two slots at the
top. Insert 2 more screws through the VESA-100 mounting holes at the bottom and tighten
all screws.
4. When removing the Monitor, the monitor arm and the monitor should be placed at the
highest position (Figure 2). Remove the 2 bottom screws from the VESA plate, loosen the
top 2 screws, and lift the monitor off the VESA plate.
NOTE: 4 x M4 screws are provided for mounting the monitor to the VESA Head, different screws may
be needed if the provided screws are not the right size, standoffs may be needed depending on the
hole pattern on the monitor.
*WARNING: Ensure that the AHM is in the highest vertical position and locked before mounting
or removing devices from the FIT Station.
**
Hex key (1/8", 3/16", M3, M4) - 1
Philips screw driver #2
8
Socket wrench (12mm, 1/2") - 1
Adjustable wrench
**
Not provided by Amico
M4 mounting
hole for VESA-75
M4 mounting
hole for VESA-100
Figure 2
www.amico.com
Amico Accessories |
85 Fulton Way, Richmond Hill
Ontario, L4B 2N4, Canada