Advertisement
MICROPHONE CONSOLE VA-FMCT-500
The indicators (I) will turn red: if the evacuation message (EVAC) was selected they will remain steady
ON. If the alert message (ALERT) was selected they will be ashing.
Again in this case, if no particular zone was selected beforehand, the selected message will be sent
Again in this case, if no particular zone was selected beforehand, the selected message will be sent out by default to all the
out by default to all the zones. If you wish to send the message out only in some zones or groups of
zones. If you wish to send the message out only in some zones or groups of zones, consult point 2.4, Sending out messa-
zones, consult point 3.4, Sending out messages to selected broadcasting zones (page 28).
To stop pre-recorded messages, hold the RESET/ACK button down until the messages are deactivated
ges to selected broadcasting zones (page xx). To stop pre-recorded messages, hold the RESET / ACK button down until the
(about 2 seconds).
messages are deactivated (about 2 seconds).
By pressing the EMERGENCY button again, the messages will be deactivated and the station will
exit the emergency mode. Remember to close the lid again.
By pressing the EMERGENCY button again, the messages will be deactivated and the station will exit the emergency mode.
Remember to close the lid again.
UK
UK
UK
UK
UK
UK
2.4. Sending out messages selectively to broadcasting zones
3.4
Sending out messages selectively to broadcasting zones
3.4
Sending out messages selectively to broadcasting zones
3.4
Sending out messages selectively to broadcasting zones
The keypad of the VA-FMCT-500 station can be used to pre-select one or more zones to which to send out hands-free or
The keypad of the TSC6000-EN station can be used to pre-select one or more zones to which to send
The keypad of the TSC6000-EN station can be used to pre-select one or more zones to which to send
3.4
Sending out messages selectively to broadcasting zones
3.4
Sending out messages selectively to broadcasting zones
The keypad of the TSC6000-EN station can be used to pre-select one or more zones to which to send
pre-recorded messages. Each zone key has three indicators showing its condition:
out hands-free or pre-recorded messages.
out hands-free or pre-recorded messages.
The keypad of the TSC6000-EN station can be used to pre-select one or more zones to which to send
3.4
Sending out messages selectively to broadcasting zones
out hands-free or pre-recorded messages.
The keypad of the TSC6000-EN station can be used to pre-select one or more zones to which to send
Each zone key has three indicators showing its condition:
Each zone key has three indicators showing its condition:
out hands-free or pre-recorded messages.
The keypad of the TSC6000-EN station can be used to pre-select one or more zones to which to send
Each zone key has three indicators showing its condition:
out hands-free or pre-recorded messages.
Each zone key has three indicators showing its condition:
Indicator
out hands-free or pre-recorded messages.
Each zone key has three indicators showing its condition:
Indicator
Colour System condition
Indicator
Colour System condition
Each zone key has three indicators showing its condition:
Indicator
Colour System condition
Indicator
Colour System condition
Indicator
Colour System condition
Indicator
Colour System condition
Green
Green
Green
Green
Green
Green
Yellow
Yellow
Yellow
Yellow
Yellow
Yellow
Yellow
Yellow
Yellow
Yellow
Yellow
Yellow
Green
Green
Green
Green
Green
Green
3.4.1 Sending out messages selectively hands-free
3.4.1 Sending out messages selectively hands-free
3.4.1 Sending out messages selectively hands-free
After activating the emergency with the EMERGENCY key (all the keys turn green to indicate general
3.4.1 Sending out messages selectively hands-free
After activating the emergency with the EMERGENCY key (all the keys turn green to indicate general
3.4.1 Sending out messages selectively hands-free
After activating the emergency with the EMERGENCY key (all the keys turn green to indicate general
pre-selection), press the buttons corresponding to the required zones. These will remain green to
pre-selection), press the buttons corresponding to the required zones. These will remain green to
After activating the emergency with the EMERGENCY key (all the keys turn green to indicate general
3.4.1 Sending out messages selectively hands-free
pre-selection), press the buttons corresponding to the required zones. These will remain green to
After activating the emergency with the EMERGENCY key (all the keys turn green to indicate general
con rm that they have been selected. At this point, press the PTT key and hold it down. The microphone
con rm that they have been selected. At this point, press the PTT key and hold it down. The microphone
pre-selection), press the buttons corresponding to the required zones. These will remain green to
After activating the emergency with the EMERGENCY key (all the keys turn green to indicate general
con rm that they have been selected. At this point, press the PTT key and hold it down. The microphone
pre-selection), press the buttons corresponding to the required zones. These will remain green to
will be activated and it will be possible to send out the announcement hands-free.
will be activated and it will be possible to send out the announcement hands-free.
con rm that they have been selected. At this point, press the PTT key and hold it down. The microphone
pre-selection), press the buttons corresponding to the required zones. These will remain green to
will be activated and it will be possible to send out the announcement hands-free.
con rm that they have been selected. At this point, press the PTT key and hold it down. The microphone
will be activated and it will be possible to send out the announcement hands-free.
con rm that they have been selected. At this point, press the PTT key and hold it down. The microphone
will be activated and it will be possible to send out the announcement hands-free.
will be activated and it will be possible to send out the announcement hands-free.
At the end of the announcement, release the PTT key and press EMERGENCY again to exit the emergency
At the end of the announcement, release the PTT key and press EMERGENCY again to exit the emergency
At the end of the announcement, release the PTT key and press EMERGENCY again to exit the emergency
mode.
mode.
At the end of the announcement, release the PTT key and press EMERGENCY again to exit the emergency
gm-elektronik.swiss | adm@gm-elektronik.swiss
mode.
At the end of the announcement, release the PTT key and press EMERGENCY again to exit the emergency
mode.
At the end of the announcement, release the PTT key and press EMERGENCY again to exit the emergency
mode.
TSC6000-EN
TSC6000-EN
27
TSC6000-EN
TSC6000-EN
TSC6000-EN
TSC6000-EN
Colour
System condition
red
Manual
emergency
Manual emergency
Manual emergency
activated
Red
Red
Manual emergency
activated
activated
Red
Manual emergency
Red
activated
Manual emergency
activated
Red
Manual emergency
activated
Red
activated
Manual emergency
Manual emergency
red
Manual emergency
Red
Red
Manual emergency
activated
activated
Red
Manual emergency
activated
Red
activated
Manual emergency
activated
Red
activated
Manual emergency
Red
activated
green
Idle condition
Idle condition
Idle condition
Idle condition
Idle condition
Idle condition
Idle condition
Fault condition
yellow
Fault condition
Fault condition
Fault condition
Fault condition
Fault condition
Fault condition
Fault condition
Fault condition
yellow
Fault condition
Fault condition
Fault condition
Fault condition
Fault condition
All
All
(key)
(key)
All
All
(key)
(key)
All
(key)
green
All
All
(key)
(key)
Status
Status
Status
Steady ON, with ALARM LED ON
Status
Status
Pre-recorded evacuation
Pre-recorded evacuation
Status
Steady ON, with
Steady ON, with
Pre-recorded evacuation
announcement under
announcement under
Status
Steady ON, with
Pre-recorded evacuation
ALARM LED ON
ALARM LED ON
Steady ON, with
announcement under
way
Pre-recorded evacuation
way
announcement under
ALARM LED ON
Steady ON, with
ALARM LED ON
way
announcement under
Pre-recorded evacuation
way
Steady ON, with
ALARM LED ON
Pre-recorded alert
announcement under
way
Pre-recorded alert
ALARM LED ON
Flashing, with
Flashing, with
Flashing, with ALARM LED ON
Pre-recorded alert
announcement
way
announcement
Pre-recorded alert
Flashing, with
ALARM LED ON
ALARM LED ON
Flashing, with
announcement
Pre-recorded alert
under way
under way
ALARM LED ON
announcement
Flashing, with
ALARM LED ON
under way
Pre-recorded alert
announcement
under way
ALARM LED ON
Flashing, with
announcement
Hands-free service
under way
Hands-free service
ALARM LED ON
Steady
Hands-free service
Steady
under way
announcement
Steady
announcement
Hands-free service
Steady
announcement
under way
Hands-free service
under way
Steady
announcement
under way
Hands-free service
Steady
announcement
under way
Zone in failed condition
Steady
announcement
under way
Zone in failed condition
Zone in failed condition
Flashing
under way
or unavailable due to
Flashing
or unavailable due to
Zone in failed condition
Flashing
or unavailable due to
Zone in failed condition
ampli er failure
ampli er failure
Flashing
Flashing
or unavailable due to
ampli er failure
Zone in failed condition
Flashing
or unavailable due to
ampli er failure
Flashing
or unavailable due to
ampli er failure
Zone set in a "disabled
Zone set in a "disabled
Steady
ampli er failure
Steady
Zone set in a "disabled
condition"
condition"
Steady
Zone set in a "disabled
Steady
Steady
condition"
Zone set in a "disabled
condition"
Steady
Zone set in a "disabled
condition"
Steady
condition"
Steady
Zone selected
Steady
Zone selected
Steady
Zone selected
Steady
Zone selected
Steady
Zone selected
Steady
Steady
Zone selected
Page 7 | 12
28
28
Meaning
Meaning
Meaning
Pre-recorded evacuation
Meaning
Meaning
Meaning
announcement under way
Meaning
Pre-recorded alert
announcement under way
Hands-free service
announcement under way
Zone in failed condition or
unavailable due to amplifier failure
Zone set in a «disabled condition»
Zone selected
Datasheet 1811.001
Advertisement
