PCE Instruments PCE-OM 15 Manual

Manual
STROBOSCOPE
PCE-OM 15
5.NOTES
5.1 This device causes moving objects to appear
still. T ake precautions against accidental contact
with moving objects.
5.2 Do not look at the emitted light for long periods
of time; it can be harmful to the eyes.
5.3 Do not touch the
5.4 Do not operate r o store instrument in following
places: explosive areas, near water, oil, dust, or
chemicals, areas where temperature is too high.

6. FLASH TUBE REPLACEMENT

when reading is displayed but unit is not
The tube might be needed to be replaced.
7. AUTO STOP FLASHING
The strobe light of stroboscope will stop
about 5 minutes after power on the
stroboscope in order to prolong lifetime of
or physically marking the object with a small
piece of tape, pencil mark, etc.
4.2 Plug the supplied power cable into the power
cable jack of the instrument. Plug the oth
of the cable into an appropriate AC power
source. Do not plug the device into an
incorrect power source otherwise damage to
the instrument will result. Use the ON/OFF
switch to turn the instrument on or
4.3 Depress the H/L button (3-4) to select the Hi
range or Low range. For
upper limits vary. Please note,
much brighter at low range than that at hi range
in order to prolong lifetime of strobe light.
4.4 Adjust the Coarse Knob 3- 5 or the Fine
Knob 3-6 from highest FPM downward. The
true RPM can be noted once the frozen appears
and the single image of
See chart in table 1 and accompanying diagram
for further explanation.
4.5 To verify RPM reading, press
image should appear again. And
2 images should appear .
4.6 While measuring, use the RANGE button to
select the range as desired. The Low range is
used for measurements below 2,500 RPM (for
E type) or 5,000 RPM (for A to D type). At low
range, g light is much brig
4.7 U se the Ext/Int button to select the external
trigger or internal trigger way as desired.
h tube.
6
e e r
.
t models, the
light is
Mark appears.
2 , a single
press x 2 ,
t h . r e
This Stroboscope is small in size, light in
weight, easy to carry. Although complex
and advanced, it is convenient to use and
operate. Its ruggedness will allow many
y e a r s o f u s e i f p r o p e r o p e r a t i n g
techniques are followed. Please read
the following instructions carefully and
always keep this manual within easy
reach.
Shaft Rotation
and Fla shes
relationship
,
n n
=
n n
=

1. FEATURES

* When the speed of the moving object matches
the
n d
object appears still
operator the illusion of
where in actuality the equipment unde r
observation is in a moving
the
to be standing still. With a slight adjustment,
movement can be viewed in app
motion. Which enables the observer or the
operator to study the process in action.
* W ide measuring range & high resol
* Digital display gives exact reading with no
guessing or errors.
* Flash timer control conserves ash tube life.
* External trigger allows unit to be automatically
Synchronize with equipment.
* Stro
light at high range.

2. SPECIFICATIONS

Display : 10 mm (0.4") LCD
Parameters Measured: FPM
Ranges : 2350A: 50~12,000 FPM
PCE Americas Inc.
711 Commerce Way
Suite 8
Jupiter
FL-33458
USA
From outside US: +1
Tel: (561) 320-9162
Fax: (561) 320-9176
info@pce-americas.com
www.pce-instruments.com/english
www.pce-instruments.com
n
stopped
n
i mages
0
- n
0
moving oppositely
single image
n
moving same
+
0
direction
h rate of the stroboscope, the moving
The unit can give the
.
stopped motion
s a t
hing rate, equipm e n n i t
ash light at low range and week
( Liquid Crystal Display )
( Flashes Per Minute)
2350B: 50~40,000
2350C: 50~20,000
2350D: 50~30,000
2350E: 50~2,000
1
PCE Instruments UK Ltd.
Units 12/13
Southpoint Business Park
Ensign way
Hampshire / Southampton
United Kingdom, SO31 4RF
From outside UK: +44
Tel: (0) 2380 98703 0
Fax: (0) 2380 98703 9
info@pce-instruments.com
note
single image
e t B . y adjusting
motion appears
a e r t n slow
t u o i . n
h
FPM
FPM
FPM
FPM