Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for PCE Instruments PCE-EVSE 300
Summary of Contents for PCE Instruments PCE-EVSE 300
- Page 1 User Manual PCE-EVSE 300 Electrical Vehicle Tester User manuals in various languages (français, italiano, español, português, nederlands, türk, polski, русский, 中文) can be found by using our product search on: www.pce-instruments.com Last change: 4 November 2021 v1.0 © PCE Instruments...
-
Page 2: Table Of Contents
Schuko plug connection ....................8 Phase measurement connection (L1, L2, L3, N, PE) ............9 Maintenance ..................9 Cleaning ........................... 9 Transport and storage ...................... 9 Replace fuse ........................9 10 Warranty ....................10 11 Disposal ....................10 © PCE Instruments... -
Page 3: Safety Notes
We expressly point to our general guarantee terms which can be found in our general terms of business. If you have any questions please contact PCE Instruments. The contact details can be found at the end of this manual. © PCE Instruments... -
Page 4: Specifications
Weight approx. 1 kg / 2.2 lb Delivery scope 1 x electrical vehicle tester PCE-EVSE 300, 1 x charging cable plug type 1, 1 x charging cable plug type 2, 1 x transport bag, 1 x user manual Safety symbols... -
Page 5: Description Of The Safety Symbols
Risk of electric shock if the signal lamp lights up during the PE test. If this lamp lights up, no further tests must be carried out until the PE error has been rectified. If the connections are incorrectly made, there is a risk of electric shock. © PCE Instruments... -
Page 6: Device Description
Signal lamp for phase connection Neutral conductor laboratory plug connection 4 mm CP rotary selector switch A, B, C, D Charging station connector (male) Connection for charging station plug (female) CP signal output CP signal output connected to protective earth Fuse © PCE Instruments... -
Page 7: Testing Charging Stations
You can then connect the charging plug to the charging station. Measurement with a permanently installed cable is also possible if an appropriate adaptor is connected in between. © PCE Instruments... - Page 8 Direct connection to the charging station and connection via an adaptor with the permanently installed cable. © PCE Instruments...
-
Page 9: Operation Of Electrical Vehicle Tester
PP cable and the protective earth conductor. This can be seen in the following chart: Cable type Resistor No cable (NC) Open 1.5 kΩ 13 A 680 Ω 20 A 220 Ω 32 A 100 Ω 63 A © PCE Instruments... -
Page 10: Cp Vehicle (Simulation)
L1, N and PE in the charging station are tapped by the Schuko plug connection. This connection can be used to make power measurements, for example to check a current display. Note: This connection is protected by the built-in 10 A fuse. © PCE Instruments... -
Page 11: Phase Measurement Connection (L1, L2, L3, N, Pe)
Ensure that there is no voltage. Then open the compartment for the fuse on the back and replace it by a 10 A (H) 250 V, 5 x 20 mm fuse. You can then close the compartment. The tester is now ready for use again. © PCE Instruments... -
Page 12: Warranty
For countries outside the EU, batteries and devices should be disposed of in accordance with your local waste regulations. If you have any questions, please contact PCE Instruments. © PCE Instruments... - Page 13 PCE Instruments contact information Germany France Spain PCE Deutschland GmbH PCE Instruments France EURL PCE Ibérica S.L. Im Langel 4 23, rue de Strasbourg Calle Mayor, 53 D-59872 Meschede 67250 Soultz-Sous-Forets 02500 Tobarra (Albacete) Deutschland France España Tel.: +49 (0) 2903 976 99 0 Téléphone: +33 (0) 972 3537 17...
Need help?
Do you have a question about the PCE-EVSE 300 and is the answer not in the manual?
Questions and answers