Rbc-Amt31E, Rbc-Amt32E - Toshiba RBC-EXW21E2 Quick Reference

Part Name
Display section
RBC-AMT21E, RBC-AMT31E, RBC-AMT32E
In the display example, all indicators are displayed for the explanation.
In reality only, the selected contents are indicated.
• When turning on the main power switch and leak breaker at the first time,
remote controller.
• While this display is flashing, the model is being automatically confirmed.Accordingly, wait for a while after
display has disappeared, and then use the remote controller.
1
8
Central control
2
3
SET DATA
4 UNIT No.
5
SETTING TEST R.C. No.
6
7
<RBC-AMT21E>
1
SETTING display
Displayed during setup of the timer etc.
2
Operation mode select display
The selected operation mode is displayed.
3
CHECK display
Displayed while the protective device works or a
trouble occurs.
4
Timer time display
Time of the timer with H mark is displayed.
(When a trouble occurs, the check code is
displayed.)
5
Timer SET IN setup display
When pushing the Timer SET IN button, the display
of the timer is selected in order of [OFF]
[OFF] repeat OFF timer → [ON]
display.
6
Filter display
If "FILTER " is displayed, clean the air filter.
7
TEST run display
Displayed during a test run.
8
Louver position display(4-way Air Discharge
Cassette,2-way Air Discharge Cassette,1-way Air
Discharge Cassette, Under Ceilingand and High
Wall Type only (2H. 3H))
Displays louver position.
9
SWING display
Displayed during up/down movement of the louver.
10
Set up temperature display
The selected set up temp. is displayed.
11
Remote controller sensor display
Displayed while the sensor of the remote controller
is used.
12
PRE-HEAT display (Heat-pump model only)
Displayed when the heating operation starts or
defrost operation is carried out.
While this indication is displayed, the indoor fan
stops or the mode enters in LOW.
2
9
CODE No.
1
10
3
11
4
5
12
6
13
14
<RBC-AMT31E>
→ No
7 8 9
20
10
17
11
16
12
14
13
13
No function display
Displayed if there is no function even if the button
is pushed.
14
Air volume select display
The selected air volume mode is displayed.
(AUTO)
(MED.)
15
Louver Number display(exapmle:01, 02, 03, 04)
(RBC-AMT32E only)
16
Operation ready display
Displayed when cooling or heating operation is
impossible because the outdoor temperature goes
out of the operable range.
17
Mode select control display
→
(RBC-AMT21E on function)
Displayed when pushing "Operation mode select
" button while the operation mode is fixed to
heating or cooling by the system manager of the
air conditioner.
18
Louver lock display(4-way Air Discharge
Cassette Type 2H series only)
(RBC-AMT32E only)
Displayed when there is a louver-locked unit in the
group (including 1 indoor unit by 1 outdoor unit).
19
Unit Number display (RBC-AMT32E only)
Unit number of the indoor unit selected with the
unit select button or abnormal indication of the
indoor/outdoor unit.
20
Central control display
(RBC-AMT21E on function)
Displayed when the air conditioner is used under
the central control in combination with a central
control remote controller.
In case the remote controller is disabled by the
central control system,
operation is not accepted.
Even when you push ON/OFF, MODE, orTEMP.
button, the button operation is not accepted.
(Settings made by the remote controller vary with
the central control mode. For details, referto the
Owner's Manual of the central control remote
controller.)
– 3 –
flashes on the display part of the
SETTING
9 20 19
8
2
1
3
4
5
6
15
7
14
18
<RBC-AMT32E>
(HIGH)
(LOW)
flashes.The button
SETTING
10
17
11
16
12
13