1. Manuals
  2. Brands
  3. Hearth & Home Manuals
  4. Indoor Fireplace
  5. B41L-AU
  6. Installation manual

Hearth & Home B41L-AU Installation Manual

Hide thumbs Also See for B41L-AU:
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
NOTICE: DO NOT discard this manual!
Models:
NOTE: NOT INTENDED FOR
NOTE:
FIREPLACE INSERT.
DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.
DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.
DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.
DO NOT MODIFY THIS APPLIANCE.
Installation Manual
Installation and Appliance Setup
Ref No: GMK10636
AS/NZS 5263.1.8
Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly
could result in serious injury, death, or
property damage.
• DO NOT store or use gasoline or other flam-
mable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Leave the building immediately.
- Immediately call your gas supplier from
a neighbor's phone. Follow the gas sup-
plier's instructions.
- If you cannot reach your gas supplier, call
the fire department.
• Installation and service must be performed
by a qualified installer, service agency, or the
gas supplier.
DANGER
DO NOT TOUCH GLASS
NEVER ALLOW CHILDREN
A barrier designed to reduce the risk of
burns from the hot viewing glass is provided
with this appliance and shall be installed for
the protection of children and other at-risk
individuals.
HOT GLASS WILL
CAUSE BURNS.
UNTIL COOLED.
TO TOUCH GLASS.
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the B41L-AU and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Hearth & Home B41L-AU

Summary of Contents for Hearth & Home B41L-AU

  • Page 1 DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE. DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION. DO NOT MODIFY THIS APPLIANCE. Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 2: Table Of Contents

    C. Securing and Leveling the Appliance ....33 D. Non-Combustible Material Installation ....34  = Contains updated information. Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 3: Installation Standard Work Checklist

    _____________________________________________________________________________________ _________________________________________________________________________________________________ _________________________________________________________________________________________________ Comments Communicated to party responsible ____________________ by ______________________on ___________ (Builder / Gen. Contractor/) (Installer) (Date)  = Contains updated information. 2570-982C 7/20 Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 4: Product Specific And Important Safety Information

    * The allowable Outlet (Manifold) Gas Pressure ranges are: Natural Gas 0.63 - 0.95 kPa (0.76 kPa nominal) and Propane 2.37 - 2.61 kPa (2.40 kPa nominal). Certification testing setpoint values are shown. Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 5: High Altitude Installations

    G. Electrical Codes All electrical safety testing has been done following the EN 60335-2-102 standard. Local codes apply. Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 6: Getting Started

    Use appropriate finishing materials that are able to withstand these conditions. For additional finishing guidelines, see Section 10. Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 7: Tools And Supplies Needed

    • Improper positioning of the logs/media (as applicable) or the glass assembly. • Installation and/or use of any component part not approved by Hearth & Home Technologies. Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 8: Framing And Clearances

    1041 16-3/4 6-5/8 32-1/4 32-3/8 15-1/4 2-3/16 33-11/16 3-1/2 17-1/4 25-7/8 46-1/2 1181 43-1/2 1105 9-13/16 6-1/8 17-3/4 7-1/2 10-3/8 30-3/4 7-3/4 Figure 3.1 Appliance Dimensions Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 9 Note: See Section 10 for hearth, mantel and finishing requirements. 33-3/16 14-1/8 38-1/8 6-7/8 9-13/16 19-7/8 26-7/8 25-3/16 B41L-AU CFTF-36 Figure 3.2 Decorative Barrier Front Dimensions - CFTF Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 10: Clearances To Combustibles

    Discharge Kit is installed. Inches 47-1/2 15-3/4 17-1/4 See Section 10.C for Alcove Installation B41L-AU (Mantel and Wall Projection). Millimeters 1207 1067 1676 Figure 3.3 Appliance Locations Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 11 ** If appliance is installed off of floor, maintain required clearances to combustibles. Construct platform in accordance with local building codes. Figure 3.4 Clearances to Combustibles Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 12 ** Measurement without Trim Kit = 2 in. (51 mm) + Additional Finishing Material Thickness. If finished discharge opening height is greater than 3 in.(76 mm), wire mesh is required. Figure 3.5 Passive Heat Front Discharge Framing Dimensions With and Without a Trim Kit Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 13 Inside Height Inside Width Outside Height Outside Width Inches 2-9/16 36-1/2 5-5/8 38-3/8 PHTRIM-36LINEAR millimeters  Figure 3.6 Passive Heat Front Discharge - Vent Cover Dimensions Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 14 Bottom of Appliance Combustible Materials Opening Opening Discharge Opening to Ceiling Inches 12-1/4 8-3/4 63-5/8 77-3/8 B41L-AU millimeters 1616 1965 Figure 3.7 Passive Heat Side Discharge Framing Dimensions Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 15 Mesh screen required for front discharge or open top discharge passive heat installations with discharge opening of 3 in. (76 mm) or greater. Figure 3.8 Passive Heat Minimum Framing Dimensions Open Top Discharge Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 16: Constructing The Appliance Chase

    If the appliance is being installed on a cement surface, a layer of plywood may be placed underneath to prevent con- ducting cold up into the room. Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 17: Termination Location And Vent Information

    49.4°-53.1° ............1 830 53.1°-56.3° ............2 130 56.3°-59.0° ............2 290 59.0°-60.3° ............2 440 *910 mm minimum in snow regions Figure 4.1 Minimum Height From Roof To Lowest Discharge Opening Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 18: Chimney Diagram

    500 mm of the opening and discharging in the direction of the opening. 4. Clearance from a flue terminal to a LP cylinder shall be a minimum of 1 meter. MINIMUM CLEARANCES REQUIRED FOR BALANCED FLUE TERMINALS OR THE FLUE TERMINALS OF OUTDOOR APPLIANCES Figure 4.3 Minimum Clearances for Termination Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 19: Approved Pipe

    8-1/2 SLP24 SLP36 25-1/2 SLP48 1219 SLP6A 3 to 6 76 to 152 2-1/8-4-1/4 54-108 SLP12A 3 to 12 76 to 305 2-1/8-8-1/2 54-216 Figure 4.4 Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 20: Measuring Standards

    • Horizontal pipe installed level with no rise. MEASURE TO SHADED SURFACE (OUTSIDE MOUNTING SURFACE) Figure 4.6 Measure to Outside Mounting Surface Figure 4.7 Measure to Top of Last Section of Pipe Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 21: Vent Diagrams

    • Horizontal termination cap should have a 1/4 in. (6 mm) downward slant to allow any moisture in cap to be released. See Figure 4.8. 1/4 in. max. (6 mm) Figure 4.8 Vent Cap Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 22 5 ft. 1.5 m 15 ft. 4.6 m H MAX. =15 ft. (4.6 m) V + H MAX. = 40 ft. (12.2 m) Figure 4.9 Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 23 5 ft. 1.5 m 15 ft. 4.6 m glass breakage. MAX. =15 ft. (4.6 m) MAX. = 40 ft. (12.2 m) INSTALLED HORIZONTALLY Figure 4.10 Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 24 CAUTION: The SLP-HRC-SS termination caps are not approved for use with these models. May lead to elevated glass temperature that may cause tempered glass breakage. Figure 4.11 Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 25 CAUTION: The SLP-HRC-SS termination caps are not approved for use with these models. May lead to elevated glass temperature that may cause tempered glass breakage. INSTALLED HORIZONTALLY INSTALLED HORIZONTALLY Figure 4.12 Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 26 Note: Use SLP Series components only. Note: If installing a vertical vent/termination off the top of the appliance, the optional vertical termination baffle may be needed. Figure 4.13 Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 27 HEAT SHIELD 3. Reinstall shield by securing it with the two wing nuts and two screws previously removed in Step 1. EXHAUST RESTRICTOR INSTALLED SCREWS Figure 4.14 Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 28 + H MAX. = 40 ft. (12.2 m) * No specific restrictions on this value EXCEPT V + H cannot exceed 40 ft. (12.2 m) Figure 4.15 Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 29 H MAX. =14 ft. (4.3 m) MAX. = 40 ft. (12.2 m) * No specific restrictions on this value EXCEPT V cannot exceed 40 ft. (12.2 m) INSTALLED HORIZONTALLY Figure 4.16 Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 30 762 mm 4 ft. 1.2 m 4 ft. 1.2 m 4 ft. 1.2 m 3-1/2 ft. 1.0 m components only. Maximum= 40 ft. (12.2 m) Figure 4.17 Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 31: Vent Clearances And Framing

    * Shows center of vent framing hole for top or rear venting. The center of the hole is 1 in. (25 mm) above the center of the horizontal vent pipe. Figure 5.2 Wall Penetration Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 32: Ceiling Firestop/Floor Penetration Framing

    INSTALL ATTIC INSULATION SHIELDS BEFORE OR AFTER INSTALLATION OF VENT SYSTEM CEILING FIRESTOP CEILING FIRESTOP INSTALLED BELOW CEILING INSTALLED ABOVE CEILING Figure 5.4 Installing the Attic Shield Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 33: Appliance Preparation

    REMOVE KNOCKOUTS TOP HEAT SHIELD IN POSITION Figure 6.2 Top Heat Shield in Position and Figure 6.3 Remove Heat Management Knockouts Heat-Zone -240V Gas Locations ® Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 34: Securing And Leveling The Appliance

    This board must be used. Do NOT remove. See Figure 6.4. FACTORY-INSTALLED NON-COMBUSTIBLE BOARD DO NOT REMOVE NAILING TABS BOTH SIDES Figure 6.4 Proper Positioning, Leveling And Securing Of Appliance Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 35: Non-Combustible Material Installation

    Refer to Section THESE PILOT HOLES 10 for more information. NOTE: BOTH LEFT & RIGHT SIDES Figure 6.6 Proper Positioning, Leveling And Securing Of Appliance Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 36: Venting And Chimneys

    • Only outer pipes need to be sealed. All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed in this manner, unless otherwise stated. Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 37: Assemble Slip Sections

    NOTICE: If slip section is too long, the inner and outer flues of the slip section can be cut to the desired length. Figure 7.6 Securing Horizontal Pipe Sections Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 38: Disassemble Vent Sections

    Figure 7.8. • Pull carefully to separate the pieces of pipe. Figure 7.7 Rotate Seams for Disassembly Figure 7.8 Align and Disassemble Vent Sections Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 39: Vertical Termination Requirements

    • Insert a bolt (provided) through the brackets and install (1 OF 3) nut. Do not completely tighten. STORM SCREWS COLLAR SEAL Figure 7.11 Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 40: Horizontal Termination Requirements

    Important Notice: Heat shields may not be field constructed. VENT DEPTH FROM BACK OF APPLIANCE TO OUTSIDE SURFACE OF EXTERIOR WALL (SEE CHART BELOW) Figure 7.12 Venting Through the Wall Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 41: Electrical Information

    Figure 8.2 Gas Valve, Backup Battery & Control Module Wiring for optional Hearth & Home Technologies approved accessories should be done now to avoid reconstruction. Follow instructions that come with those accessories. Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 42: Wiring Requirements

    JUMPER WIRE RED WIRE BLACK BLACK ORANGE WIRE BLACK BLACK WIRE BATTERY PACK BROWN WIRE THERMOSTAT WIRE ASSEMBLY/ WALL SWITCH WIRE Figure 8.3 IntelliFire™ Plus Wiring Diagram Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 43: Gas Information

    • Close the manual shutoff valve BEFORE pressure testing gas line at test pressures Figure 9.1 Base Pan Removal equal to or less than 1/2 psig. Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 44 Remove glass assembly and utilize an appropriate sized screwdriver. See Figure 8.2. REMOVE PILOT AND PILOT SHIELD SCREWS REMOVE BURNER SCREW Figure 9.2 Burner Removal Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 45: Gas Connection

    Traditional or Driftwood Option Log Option B41L-AU (NG) 1/8 in. (3 mm) 3/16 in. (5 mm) B41L-AU (LP) 1/4 in. (6 mm) 5/16 in. (8 mm) Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 46: Finishing

    Figure 10.1 and Figure 10.2. Materials that are reported as passing ASTM E 136, Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 ºC. Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 47: Non-Combustible Board And Drywall Installation

    5. To ensure good adhesion of drywall compounds and tape, thoroughly clean the non-combustible board and surrounding drywall to remove dust. The non-com- bustible board may be primed with a high-quality PVA primer. Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 48 Note: It is acceptable to use a silicone sealant with a minimum of 300 ºF (149 ºC) continuous exposure rating to adhere drywall to lower cover panel. Figure 10.2 Finishing Details Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 49: Mantel And Wall Projections

    Figure 10.4 Minimum Vertical and Maximum Horizontal Figure 10.7 Combustible and Non-Combustible Mantel Leg or Dimensions of Combustibles Wall Projections (Acceptable on both sides of opening) Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 50 (DISCHARGE SLOTS ON BOTH SIDES OF APPLIANCE) 8-3/4 IN. (222 mm) 12-1/4 IN. (311 mm) = COMBUSTIBLE MATERIAL ALLOWED Figure 10.8 Finishing Material installed with Passive Heat Optional Heat Management System Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 51: Decorative Barrier Front Finishing

    FINISHING MATERIAL (TOP EDGE) Finishing materials 1 in. (25 mm) maximum thick. Stop finishing material flush with opening. Figure 10.9 Overlap Fit Decorative Front (CFTF Decorative Front) Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 52 Figure 10.11 Maximum Non-Combustible Finish Material FRONT ASSEMBLY Thickness - CFTF Decorative Barrier Front TOP VANITY PANEL (NOT SHOWN) Figure 10.13 CFTF Front Installation With Outer Decorative Barrier Front Trim Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 53 Figure 10.14 Clearances to Appliance Opening Without Outer Decorative Barrier Front Trim (BOTH SIDES) (BOTH SIDES) Figure 10.15 CFTF Front Without Outer Decorative Barrier Front Trim Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 54 NOTE: The TV installation requirements are the same regardless of whether the Passive Heat kit is installed with a top discharge, side discharge or open top discharge. Figure 10.16 Good Faith Guidelines for TV Installations Above a Fireplace with Passive Heat Option  Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 55: Appliance Setup

    NOTICE: When installing stones, driftwood logs and glass media into the B41L-AU, burner must be replaced with part number 2617-007. See installation manual for burner replacement instructions. Figure 11.3 Place Log #7 Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 56 The other end of the Figure 11.5 Place Log #3 logs rests on the smooth area on Log #7 as noted in Figure 11.7. See Figure 11.8. Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 57 MINERAL WOOL MINERAL WOOL LAVA LAVA ROCK ROCK Figure 11.10 Properly Placed Lava Rock / Location for Mineral Wool Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 58: Fixed Glass Assembly Removal And Replacement

    If the glass frame assembly does not pull back towards the face of the appliance, repeat steps 1-4. Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 59: Install Decorative Barrier Front

    For more information refer to the instructions supplied with your decorative barrier front. Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 60: Reference Materials

    1-1/2 in. 12 in. 5-1/2 in. 220 mm 38 mm 305 mm 146 mm SLP-WS SLP-FS Wall Shield Firestop Ceiling Firestop Figure 12.1 SLP Series Vent Components Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 61 235 mm Horizontal Termination Cap 14-7/16 in. 367 mm 2-5/16 in. 14-7/16 in. 59 mm 367 mm SLP-WT-BK Wall Thimble-Black Figure 12.2 SLP Series Vent Components Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 62 7-3/4 to 10-3/8 in. (197 to 264 mm) 12 IN. DVP-FBHT 305 mm Horizontal SLP-TB1 Termination Cap Basement Vent Cap (SL-2DVP Required) Figure 12.3 SLP Series Vent Components Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...
  • Page 63 Note: A PVLP-HS heat shield is available and sold separately. Use if the PVLP-SLP is installed in a high traffic area. Figure 12.4 PVLP-SLP-AU Vent Components Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

  • Page 64: Accessories

    Please contact your Hearth & Home Technologies dealer with any questions or concerns. For the location of your nearest Hearth & Home Technologies dealer, please visit www.hearthnhome.com. Printed in U.S.A. - Copyright 2020 Hearth & Home Technologies • B41L-AU Installation Manual • 2570-980 Rev. C • 7/20...

Table of Contents