Portwell ROBO-8113VG2AR User Manual

Portwell ROBO-8113VG2AR User Manual

Picmg 1.3 single host board

Advertisement

ROBO-8113VG2AR
ROBO-8113VG2AR
PICMG 1.3 Single Host Board
Version 1.1
Copyright © Portwell 2016
ROBO-8113VG2AR User's Guide
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ROBO-8113VG2AR and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Portwell ROBO-8113VG2AR

  • Page 1 ROBO-8113VG2AR ROBO-8113VG2AR PICMG 1.3 Single Host Board Version 1.1 Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 2 ROBO-8113VG2AR Revision History R1.0 Preliminary Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 3: Table Of Contents

    Main Memory ........................................32 Installing the Single Board Computer ................................... 33 5.3.1 Chipset Component Driver ..................................... 33 5.3.2 Intel® HD Graphics 530 ......................................34 5.3.3 Intel LAN I210AT/I219LM Gigabit Ethernet Controller ............................34 Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 4 Save & Exit ..........................................87 Troubleshooting ............................................. 89 Hardware Quick Installation ....................................89 BIOS Setting ......................................... 91 FAQ ............................................92 Portwell Software Service ........................................97 Industry Specifications ........................................... 98 Industry Specifications ......................................98 Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 5 Portwell provides no warranty with regard to this user’s guide or any other information contained herein and hereby expressly disclaims any implied warranties of merchantability or fitness for any particular purpose with regard to any of the foregoing. Portwell assumes no liability for any damages incurred directly or indirectly from any technical or typographical errors or omissions contained herein or for discrepancies between the product and the user’s guide.
  • Page 6 Warranty”). Portwell may in its sole discretion modify its Limited Warranty at any time and from time to time. Beginning on the date of shipment to its direct customer and continuing for the published warranty period, Portwell represents that the products are new and warrants that each product failing to function properly under normal use, due to a defect in materials or workmanship or due to non conformance to the agreed upon specifications, will be repaired or exchanged, at Portwell’s option and expense.
  • Page 7 Caution: Do not just hold any single side of the SBC; hold evenly on both sides!  Heavy processor cooler may bend the SBC when SBC being held just on one side.  The bending may cause soldering or components damaged. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 8 Caution: Suggest your S.I or vendor to use a metal bracket to hold/fix the desktop or server grade SBC to avoid the vibration damage during transportation. Heavy processor cooler may bend the SBC when systems are during transportation without any holder. Example: 4U chassis :   Use L type mental or plastic or rubber bracket to hold SBC. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 9 ROBO-8113VG2AR 2U or 1U chassis: a mental bracket on the bottom of chassis to balance and support SBC from bending.  Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 10: Introduction

    DirectX® 12. It supports triple display function via DVI-I (VGA and DVI-D) and HDMI up to 4Kx2K. Rich I/O functions are also provided by ROBO-8113VG2AR single host board, which is 10x USB 3.0, 2x USB 2.0, 6x SATA III ports (dual ports via backplane), 2x RS232 ports, 2x smart COM ports which select RS232/422/485 mode by bios adjustment, and dual Intel GbE LAN ports.
  • Page 11: Specifications

    Supports dual 10/100/1000 Mbps Ethernet port (s) via PCI Express x1 interface by Intel WGI219LM and ◆ Ethernet WGI210AT controller Dual RJ45 connector on bracket ◆ On-board TPM 2.0 support (TPM IC: Infineon SLB9665TT2.0) ◆ High Drive GPIO One pin-header for GPIO (8bit in &8bit out) ◆ Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 12: Supported Operating Systems

    ◆ Board size: 338.5mm x 126.39mm, 13.33" (L) x 4.98" (W) ◆ Supported Operating Systems The ROBO-8113VG2AR supports the following operating systems.  Windows 7 support  Windows 8.1 / WEI 8.1 support  Windows 10 full support  Kernel.org Distribution Copyright ©...
  • Page 13: Mechanical Dimensions

    ROBO-8113VG2AR Mechanical Dimensions Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 14 ROBO-8113VG2AR Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 15: Power Consumption

    Power Consumption Test Configuration CPU Type Intel® Core™ i5-6500TE CPU @ 3.2GHz (ES) L3: 6MByte SBC BIOS Portwell, Inc. ROBO-8113VG2AR-Q170-PCIE1 TEST BIOS (60105T00) Memory WARIS UB-DIMM DDR4 2133 8GB*2 (SEC K4A4G085WD) VGA Card Onboard Intel® HD Graphics 530 VGA Driver Intel®...
  • Page 16: Environmental Specifications

    System +5V 1.19A 1.63A 1.63A System+ Device +12V 0.40A 0.94A 0.89A System+ Device +5V 2.39A 2.64A 2.68A Environmental Specifications Storage Temperature : -20~80°C Operation Temperature : 0~60°C Storage Humidity : 5~90% Operation Humidity: 10~90% Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 17 ROBO-8113VG2AR Block Diagram Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 18: Hardware Configuration

    ROBO-8113VG2AR 3 Hardware Configuration Jumpers and Connectors This chapter indicates jumpers’, headers’ and connectors’ locations. Users may find useful information related to hardware settings in this chapter. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 19: Jumpers Settings

    Jumpers Settings For users to customize ROBO-8113VG2AR’s features. In the following sections, Short means covering a jumper cap over jumper pins; Open or N/C (Not Connected) means removing a jumper cap from jumper pins. Users can refer to Figure 1 for the Jumper allocations.
  • Page 20 1x8 , 2x4 3-4, Short 1-2, Open Reserved 3-4, Short 1-2, Short 3-4, Open 1-2, Open 1x16 3-4, Open JP4: Clear CMOS Setup PIN No. Description 1-2, Short Normal 2-3, Short Clear CMOS Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 21 ROBO-8113VG2AR JP5: WDT Enable/Disable Pin PIN No. Description 1-2 Short WDT Enable 1-2 Open WDT Disable JP6: ATX/AT Select Pin PIN No. Description 1-2 Short AT mode 1-2 Open ATX mode Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 22: Connector Settings

    DDR4 Channel A Slot SM Bus Pin Header PH5Px1/2.54mm Front Panel Pin Header Header 8Px2/2.54mm GPIO Pin Header Header 5Px2/2.54mm ATX 8 Pin Connector(For CPU Power) J17/J20 USB2.0/3.0 connector(D-Sub) COM1 Pin Header COM2 Pin Header Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 23 DVI-I Connector Audio Pin Header Header 5Px2/2.54mm System Fan J1: Keyboard/Mouse Connector PIN No. Signal Description PIN No. Signal Description Mouse Data Keyboard Data Ground Ground PS2 Power PS2 Power Mouse Clock Keyboard Clock Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 24 ROBO-8113VG2AR J2/J7/J15/J16:SATA Connector PIN No. DESCRIPTION Ground TX_P TX_N Ground RX_N RX_P Ground Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 25 PIN No. Description 5V_Dual USB3.0_RX_N 5V_Dual USB3.0_RX_P USB3.0_RX_N Ground USB3.0_RX_P USB3.0_TX_N Ground USB3.0_TX_P USB3.0_TX_N Ground USB3.0_TX_P USB2.0_N Ground USB2.0_P USB2.0_N Ground USB2.0_P J9: SM Bus Pin Header PIN No. Description Clock Ground Data Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 26 I210_LAN (+) 12 Power Button Signal HDD_LED (+) 14 Reset Signal HDD_LED (-) 16 Ground J11: GPIO Pin Header PIN No. Description PIN No. Description GPIO_0 GPIO_4 GPIO_1 GPIO_5 GPIO_2 GPIO_6 GPIO_3 GPIO_7 Ground Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 27 J12: ATX 8 Pin Connector(For CPU Power) PIN No. Description PIN No. Description Ground +12V Ground +12V Ground +12V Ground +12V J18/J19/J22/J23: COM1/COM2/COM3/COM4 Pin Header PIN No. Description PIN No. Description DCD# RXD# TXD# DTR# Ground DSR# RTS# CTS# Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 28 ROBO-8113VG2AR J27: Audio Pin Header PIN No. Description PIN No. Description MIC_IN Ground LINE_IN_L Ground LINE_IN_R Ground AUDIO_OUT_L Ground AUDIO_OUT_R Ground Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 29: Signal Descriptions

    #Define WDTMIN 0x07 //WDT Timer Counter Register (Minute) #Define WDTSEC 0x08 //WDT Timer Counter Register (Second) VOID Write_EC_SRAM(UINT8 Offset,UINT8 Value){ IoWrite8(0xE300+Offset,Value); Byte Read_EC_SRAM(UINT8 Offset){ IoRead8(0xE300+offset,Value); return Value; void WDT() // Enable WDT 30sec Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 30 Write_EC_SRAM(WDTCFG,0x01); //Bit0: WDT Enable, BIT1: 0:Second Mode // Enable WDT 5min Write_EC_SRAM(WDTSEC,5); Write_EC_SRAM(WDTCFG,0x03); //Bit0: WDT Enable, BIT1: 1:Minute Mode // Enable WDT 10min, 20sec Write_EC_SRAM(WDTSEC,20); Write_EC_SRAM(WDTSEC,10); Write_EC_SRAM(WDTCFG,0x03); //Bit0: WDT Enable, BIT1: 1:Minute Mode Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 31: Gpio Signal

    IoWrite8(0xE300+Offset,Value); Byte Read_EC_SRAM(UINT8 Offset){ IoRead8(0xE300+offset,Value); return Value; void GPIO() int Temp; // Get GPIO data Temp = Read_EC_SRAM(GPDR); // Set GPIO7 High Temp |= 0x80; Write_EC_SRAM(GPDR,Temp); //Bit7: GPIO7 status, 0: Low 1: High Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 32: System Resources

    Intel® C236 Chipset (Intel® GL82C236 PCH) Main Memory ROBO-8113VG2AR provides 2 x 288-pin Long-DIMM sockets which supports DDR4 ECC/non-ECC memory. The maximum memory can be up to 32GB. Memory clock and related settings can be detected by BIOS via SPD interface.
  • Page 33: Installing The Single Board Computer

    To overcome this compatibility issue, for Windows Operating Systems such as Windows 8, please install its INF before any of other Drivers are installed. You can find very easily this chipset component driver in ROBO-8113VG2AR CD-title Copyright ©...
  • Page 34: Intel® Hd Graphics 530

    Intel® HD Graphics 530 ROBO-8113VG2AR has integrated Intel® HD Graphics 530 which supports DirectX 12、OpenCL 2.0、OpenGL 4.4. It is the most advanced design to gain an outstanding graphic performance. ROBO-8113VG2AR supports VGA+DVI-D by DVI-I connector on bracket, and on board HDMI display output. This combination makes ROBO-8113VG2AR an excellent performance hardware.
  • Page 35: Bios Setup Items

    The BIOS setup program provides a General Help screen. The menu can be easily called up from any menu by pressing <F1>. The Help screen lists all the possible keys to use and the selections for the highlighted item. Press <Esc> to exit the Help Screen. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 36 ROBO-8113VG2AR Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 37: Main

    ROBO-8113VG2AR 6.2.1 Main Use this menu for basic system configurations, such as time, date etc. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 38 The date format is <Day>, <Month> <Date> <Year>. Use [+] or [-] to configure system Date. System Time The time format is <Hour> <Minute> <Second>. Use [+] or [-] to configure system Time. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 39: Configuration

    ROBO-8113VG2AR 6.2.2 Configuration Use this menu to set up the items of special enhanced features Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 40 ROBO-8113VG2AR CPU Configuration CPU Configuration Parameters Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 41 Enable/Disable C1E. When enabled, CPU will switch to minimum speed when all cores enter Enhanced C-states ★Enabled, Disabled C-State. ★C1 and C3, Disabled, C-State Auto Demotion Configure C-State Auto Demotion. C1, C3, ★C1 and C3, Disabled, C-State Un-demotion Configure C-State Un-demotion. C1, C3, Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 42 Disable – Sets bit 30 of POWER_CTL MSR(0x1FC) to 1 to disable the C State Pre-Wake ★Enabled, Disabled ★AUTO, C0/C1, C2, C3, Package C State limit Package C State limit C6, C7, C7s, C8 CFG lock Configure MSR 0xE2 [15], CFG lock bit. ★Enabled, Disabled Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 43 ROBO-8113VG2AR Chipset Configuration Configuration Chipset feature Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 44 HD Audio Disabled = HAD will be unconditionally disabled ★Enabled, Disabled Enabled = HAD will be unconditionally Enabled Port 80h Redirection Control where the port 80h cycles are sent. ★LPC Bus, PCIE Bus Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 45 ROBO-8113VG2AR AMT Configuration Configure Active Management Technology Parameters Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 46 Note: iAMT H/W is always enabled. ★Disabled, Enabled (Enabled) This option just controls the BIOS extension execution. If enabled, this requires additional firmware in the SPI device Un-Configure ME OEMFlag Bit 15: Un-Configure ME without password. ★Disabled, Enabled Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 47 ROBO-8113VG2AR LAN Configuration Configuration on Board LAN device. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 48 Intel I210 LAN Controller. Disabled, ★Enabled Launch Legacy PXE Rom. [Disable] Not launch Rom, [Enable] Force launch Rom, [Auto] Launch Legacy PXE Rom ★Disable, Enable, Auto Auto detect LAN Cable state to Enable/Disable Rom initial. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 49 ROBO-8113VG2AR Graphics Configuration Configuration Graphics Settings Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 50 To use this feature, please disable CSM Support. ★32M,64M,96M,128M, 160M,192M,224M,256M,288M ,320M,352M,384M,416M,448 Select DVMT 5.0 Pre-Allocated (Fixed) Graphics Memory size used by the Internal Graphics M,480M,512M, DVMT Pre-Allocated Device. 1024M,1536M,2048M, 4M, 8M,12M,16M,20M,24M,28M,3 2M,/F7,36M,40M,44M,48M,52 M,56M,60M Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 51 Secondary boot display selection will appear based on your selection. VGA modes will be supported only on primary display. Secondary IGFX Boot Display Select Secondary Display Device. ★Disabled, HDMI, DVI, VGA Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 52 ROBO-8113VG2AR PCI/PCIE Configuration PCI, PCI-X and PCI Express Settings. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 53 Enable or disable PCI Express Clock Gating for each root port. Disabled ★Enabled DMI Link ASPM Control Enable/Disable the control of Active State Power Management on SA side of the DMI Link. Disabled ★Enabled Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 54 ROBO-8113VG2AR PCI Express Root Port7, Port9, Port10, Port11, Port12 PCI Express Root Port7, Port9, Port10, Port11, Port12 Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 55 Force L0s – Force all links to L0s State ★Disabled, L0s, L1, L0sL1, ASPM Support AUTO-BIOS auto configure Auto DISABLE – Disables ASPM PCIe Speed Select PCI Express port speed ★Auto, Gen1, Gen2, Gen3 Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 56 ROBO-8113VG2AR SATA Configuration SATA Device Options Settings Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 57 Designates this port as Hot Pluggable ★Disabled, Enabled External SATA External SATA Support. ★Disabled, Enabled ★hard Disk Drive, Solid State SATA Device Type Indentify the SATA port is connected to Solid State Drive or Hard Disk Drive. Drive Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 58 ROBO-8113VG2AR USB Configuration USB Configuration Parameters. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 59 Mass Storage device emulation type. ‘AUTO’ enumerates devices according to their media ★Auto, Floppy, Forced FDD, Mass Storage Devices format. Optical drives are emulated as ‘CDROM’, drives with no media will be emulated Hard Disk, CD-ROM according to a drive type. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 60 ROBO-8113VG2AR PCH USB Configuration PCH USB Configurtion Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 61 USB Port Disable Override Selectively Enable/Disable the corresponding USB port from reporting a Device ★Disabled, Select Per-Pin (Select Per-Pin) Connection to the controller. USB HS Physical Connector #0 - #13 Enable/Disable USB Port. ★Enabled, Disabled Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 62 ROBO-8113VG2AR Power Control Configuration System Power Control Configuration Parameters Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 63 Wake up day 1-31 like the system to wake up Wake up Time(HH: mm: ss) Use [Enter], [TAB] to select field, HH: 0-23, mm: 0-59, ss: 0-59 HH: 0-23, mm: 0-59, ss: 0-59 Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 64 ROBO-8113VG2AR TPM Configuration Trusted Computing settings Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 65 TPM 1.2 will restrict support to TPM 1.2 devices, TPM 2.0 will restrict support to TPM 2.0 Device Select devices, Auto will support both with the default set to TPM 2.0 devices if not found, TPM ★Auto, TPM 1.2, TPM 2.0 1.2 devices will be enumerated. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 66 ROBO-8113VG2AR Super IO Configuration System Super IO Chip Parameters. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 67 ROBO-8113VG2AR Feature Description Options Watch Dog Timer Enable/Disable Watch Dog Timer ★Disabled, Enabled (Enabled) Timer Unit Select Timer count unit of WDT ★Second, Minute Timer value Set WDT Timer value ★20 Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 68 ROBO-8113VG2AR Serial Port 1 Configuration Set Parameters of Serial Port 1 (COM 1) Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 69 Description Options Serial Port Enable or Disable Serial Port (COM) ★Enabled, Disabled ★IO=3F8h; IRQ=4, Auto, IO=240h; IRQ=3,4,5,6,7,10,11,12 Change Settings Select an optimal settings for Super IO Device IO=248h; IRQ=3,4,5,6,7,10,11,12 IO=250h; IRQ=3,4,5,6,7,10,11,12 IO=258h; IRQ=3,4,5,6,7,10,11,12 Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 70 ROBO-8113VG2AR Serial Port 2 Configuration Set Parameters of Serial Port 2 (COM 2) Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 71 Description Options Serial Port Enable or Disable Serial Port (COM) Disabled, ★Enabled ★IO=2F8h; IRQ=3; Auto, IO=240h; IRQ=3,4,5,6,7,10,11,12 Change Settings Select an optimal settings for Super IO Device. IO=248h; IRQ=3,4,5,6,7,10,11,12 IO=250h; IRQ=3,4,5,6,7,10,11,12 IO=258h; IRQ=3,4,5,6,7,10,11,12 Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 72 ROBO-8113VG2AR Serial Port 3 Configuration Set Parameters of Serial Port 3 (COM 3) Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 73 Serial Port 3 RS-232/422/485 Control Option RS-485 HALF DUPLEX RS-485/422 FULL DUPLEX ★IO=240h; IRQ=11, Auto, IO=240h; IRQ=3,4,5,6,7,10,11,12 Change Settings Select an optimal setting for Super IO Device. IO=248h; IRQ=3,4,5,6,7,10,11,12 IO=250h; IRQ=3,4,5,6,7,10,11,12 IO=258h; IRQ=3,4,5,6,7,10,11,12 Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 74 ROBO-8113VG2AR Serial Port 4 Configuration Set Parameters of Serial Port 4 (COM 4) Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 75 RS-232/422/485 Control Option Serial Port 4 RS-232/422/485 Control Option RS-485 HALF DUPLEX RS-485/422 FULL DUPLEX ★IO=248h; IRQ=11, Auto, IO=240h; IRQ=3,4,5,6,7,10,11,12; Change Settings Select an optimal settings for super IO Device IO=248h; IRQ=3,4,5,6,7,10,11,12; IO=250h; IRQ=3,4,5,6,7,10,11,12; IO=258h; IRQ=3,4,5,6,7,10,11,12; Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 76 ROBO-8113VG2AR H/W Monitor Configuration Monitor hardware status Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 77 CPU Full Fan Target Temperature. Smart System Fan Function Enable or Disable Smart System Fan ★Disabled, Enabled (Enabled) System Start Target Temp System Start Fan Target Temperature. System Full Target Temp System Full Fan Target Temperature. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 78 ROBO-8113VG2AR Serial Port Console Redirection Serial Port Console Redirection Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 79 ROBO-8113VG2AR Feature Description Options Console Redirection (COM 0-5) Console Redirection Enable or Disable. ★Disabled, Enabled (Enabled) Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 80 ROBO-8113VG2AR COM 0 Serial Port Console Redirection COM0 Serial Port Console Redirection Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 81 ‘stop’ signal can be sent to stop the data flow. Once Flow Control ★None, Hardware RTS/CTS the buffers are empty, a ‘start’ signal can be sent to re-start the flow. Hardware flow control uses two wires to send start/stop signal. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 82 The settings specify if BootLoader is selected then Legacy console redirection is Redirection After BIOS POST disabled before booting to legacy OS. Default value is Always Enable with means ★Always Enable, BootLoader Legacy console Redirection is enabled for Legacy OS. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 83: Security

    ROBO-8113VG2AR 6.2.3 Security This section lets you set security passwords to control access to the system at boot time and/or when entering the BIOS setup program. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 84 [Setup] check password when enter setup screen. [Power on] check password on Password Check Mode ★Setup, Power on every time system power on. Administrator Password Set Administrator Password ★No default setting 1st-6th HDD Security HDD Security Configuration for selected drive. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 85: Boot

    ROBO-8113VG2AR 6.2.4 Boot Use this menu to specify the priority of boot devices. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 86 Summary Screen Support Enabled/Disabled ★Disabled, Enabled Boot option filter This option controls Legacy/UEFI ROMs priority ★Legacy only, UEFI only Hard Drive BBS Priorities Set the order of the legacy devices in this group Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 87: Save & Exit

    ROBO-8113VG2AR 6.2.5 Save & Exit Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 88 UEFI: Built-in EFI Shell Reset the system after saving the changes. (Boot option filter: UEFI only) Attempts to Launch EFI Shell application (Shell.efi) from one of the available Launch EFI Shell from filesystem device filesystem devices. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 89: Troubleshooting

    7 Troubleshooting This chapter provides a few useful tips to quickly get ROBO-8113VG2AR running with success. As basic hardware installation has been addressed in Chapter 2, this chapter will focus on system integration issues, in terms of BIOS setting, and OS diagnostics.
  • Page 90 All you need to operate AHCI, RAID (0/1/5/10) application for system, please follow up setting guide in BIOS setup utility. ROBO-8113VG2AR can support six SATA interface (SATAIII, 6.0Gb/s) on board. It has four J2/J7/J15/J16 SATA ports on board; two SATA ports on PICMG Backplane.
  • Page 91: Bios Setting

    BIOS setting back to the initial factory configurations. It is recommended to do this so you can be sure the system is running with the BIOS setting that Portwell has highly endorsed. As a matter of fact, users can load the default BIOS setting at any time when system appears to be unstable in boot up sequence.
  • Page 92: Faq

    Question: I forgot my password of system BIOS, what am I supposed to do? Answer: You can switch off your power supply then find the JP4 on the ROBO-8113VG2AR SBC to set it from 1-2 short to 2-3 short and wait 5 seconds to clean your password then set it back to 1-2 short to switch on your power supply.
  • Page 93 ROBO-8113VG2AR Question: How to update the BIOS file of ROBO-8113VG2AR? Answer: 1. Please visit web site of Portwell download center as below hyperlink http://www.portwell.com.tw/support/download_center.php Registering an account in advance is a must. (The E-Mail box should be an existing Company email address that you check regularly.) http://www.portwell.com.tw/member/newmember.php...
  • Page 94 B. Click the Windows Start button, and click Windows7 USB/DVD Download Tool to execute. C. Choosing the ISO file, type the name and path of your Windows ISO file, or click Browse and select the file from the open dialog box. Click Next. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 95 Please navigate to the USB3_Fix folder in the cmd shell, and type in the following commands in this order to update the boot.wim file: (1) dism /mount-wim /wimfile:boot.wim /index:2 /mountdir:mount (2) dism /image:mount /add-driver:"usb3" /recurse Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 96 7. Please copy both two file back to the \source of the root of your USB bootable device. Then you can install the Win7 O/S which has been included the USB3.0 driver by USB bootable device. Copyright © Portwell 2016 ROBO-8113VG2AR User's Guide...
  • Page 97: Portwell Software Service

    Portwell. Portwell BIOS web Tool (PBT) The Portwell BIOS web Tool (PBT) is a brand new on-line utility which innovated by Portwell. PBT now is available for Portwell's premiere customers who are able to add customized BIOS logo and change BIOS default settings on American Megatrends (AMI) BIOS.
  • Page 98: Industry Specifications

    ROBO-8113VG2AR 9 Industry Specifications Industry Specifications The list below provides links to industry specifications that apply to Portwell modules. Low Pin Count Interface Specification, Revision 1.0 (LPC) http://www.intel.com/design/chipsets/industry/lpc.htm Universal Serial Bus (USB) Specification, Revision 2.0 http://www.usb.org/home PCI Specification, Revision 2.3 https://www.pcisig.com/specifications...

Table of Contents